• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.6
• /
• pp.230-237
• /
• 2000

The wheel bearing in vehicles has been improved to unit module by joining a bearing to a hub in order to achieve weight reduction and easy assembly. Currently, the contact force between a raceway and balls of a bearing is applied as the external force in order to analyse the structure of the unit type bearings. In this paper, simplified boundary conditions are discussed for structure analysis of wheel bearing unit. From the procedure, the contact conditions of balls and race in wheel bearing unit are considered as equivalent non-linear spring elements. The end node of a spring element is constrained in displacement. And the external force of boundary conditions is applied at the contact point between tire and road. For the evaluation of this analysis, its results for the force of spring elements are compared with contact forces of calculated results. and also maximum equivalent stresses of analysis are compared with results of test at the flange of inner ring. The analysis results with proposed boundary conditions are more accurate than results from analysis which is generally used.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.5
• /
• pp.65-70
• /
• 2012

Torque fluctuation of engine generate gear rattle noise of transmission and many researches have been studied to decrease rattle noise by adjusting clutch damper system. So design optimization of clutch system is very important to decrease rattle noise and need knowing clutch dynamic torque at real vehicle driving condition. This makes it possible to measure clutch dynamic torque by using a small-size magnetic sensor. We install a small-size magnetic sensor on the input shaft of the transmission and measure the relative angular displacement between clutch hub and disc plate. We can obtain the clutch torque correspond to the angular displacement in the clutch torsional characteristics test. The object of this research is to measure clutch dynamic torque on real vehicle condition. Therefore, Clutch dynamic torque is very useful for investigating operating range of clutch according to engine torque and predicting the damping performance of torsional vibration on the powertrain.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.9
• /
• pp.517-524
• /
• 2019

The overdrive hub clutch is attached to a 6-speed automatic transmission to reduce fuel consumption by using the additional power of the engine. This paper proposes a means to minimize the load and roll-over ratio on the punch during the piercing process for the overdrive hub clutch product. Die clearance, shear angle, and friction coefficient, which can affect the load and roll-over ratio of the punch during processing, were set as the design variables. Sensitivity analysis was also conducted to determine the influence of each design variable on the punch load and roll-over ratio. As a result, shear angle, friction coefficient and die clearance were found to be sensitive to load and roll-over ratio. The punch load and roll-over ratio were set as the objective function and the equation of each design variable and objective function was derives using the Response Surface Method. Finally, the optimal value of the design variables was derived using the Response Surface Method. Application of this model to finite element analysis resulted in 22.14% improvement in the roll-over ratio of the punch load and material.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.256-262
• /
• 2016

This study performed the back-pressure cold forging analysis to minimize the non-forming area of gear teeth for the output hub and reaction hub in automatic transmission. Two important factors of the back-pressure cold forging process, the load of the punch and the backup force applied to the sleeve, were determined through displacement control analysis. The non-forming area of the gear teeth was compared with both cases of the displacement control analysis and load control analysis, and their solution is similar to the measuring result of a real workpiece. The results show that the load of the punch is dependent on the reduction area of the workpiece, and the backup force applied to the sleeve is determined with regard to the cross-section-area of sleeve. This analysis procedure can be useful and effective in determining the manufacturing condition of the back-pressure cold forging process to minimize the non-forming area.

• Journal of the Korea Convergence Society
• /
• v.11 no.6
• /
• pp.209-213
• /
• 2020

In this study, the model A with the existing shape used at racing car and the model B with light weight were designed. The structural analysis with thermal deformation and stress were carried out. Model A shows that the maximum temperature is lower than model B. The cooling performance due to the shape of the disk without any other cooling conditions can be shown to be better for model A. Model A was seen to be superior in durability as the thermal stress reduced by almost twice as much as model B. The part where the greatest stress occurred appeared to be the hole jointed with the hub regardless of its shape. The analysis results at this study are seen to be useful at designing the shape of the actual vehicle brake disc. The analysis results obtained in this study can be applied at grasping the strength of the brake disk for racing car practically. By utilizing the analysis result of the brake disk for racing car, this study is seen as the convergence study that the aesthetic design and analysis are applied.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.2
• /
• pp.1-11
• /
• 2011

The skid-steering method that applied a number of mobile robot currently is extremely effective in narrow area. But it contains several problems such as its natural properties, slip, occurred by different direction between vehicle's driving and wheel's rotary. Through this paper, suitable control algorithm of $6{\times}6$ skid steering wheeled vehicle and its driving methods are proposed by analyzing the behavior $6{\times}6$ skid-steered wheeled vehicle model designed by engineering analysis strategy. To do this, based on a behavior of designed driving system, required torque and other performance of in-wheel type motor system are considered, and finally control algorithm for each wheel is proposed and simulated using this model. To test the proposed vehicle system, driver model is designed using PID closed loop system and included in the total driving control algorithm. The Performance of designed vehicle model is verified by using DYC (Direct Yaw Control) cornering mode and slip mode control to follow the steering input which are essential to evaluate the driving performance of $6{\times}6$ vehicle. Proposed modeling strategy and control method will be implemented to the real $6{\times}6$ in-wheel drive type vehicle.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.22 no.8
• /
• pp.562-566
• /
• 2010

Wind energy is one of the most general natural resources in the world. However, as of today, generating electricity out of wind energy is only available from big wind generator, Furthermore, an axial-flow turbine is the only way to produce electricity in the big wind generator. This paper is for the guidance of drawing impact fact about power turbine using cross-flow type transferring wind energy to electricity energy. It will find the ideal value which enables to make cross-flow power turbine(CPT) using computational fluid dynamics(CFD) code. This study tries to analyze the "Solidity" characteristics. We can find out turbine-blade number through CFD. CFD is using "Fluent_ver 6.3.16", and the data from its result will judge fan-blade performance through specific torque and specific power from each "Solidity" model. Based upon the above, we will make cross-flow power turbine of multi-blade centrifugal fan instead of axial-flow type.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.10
• /
• pp.648-654
• /
• 2018

In order to maintain manholes installed on the road, the manhole should be easy to open and close. Manhole covers under harsh conditions require that they can be lifted when attempting to open the manhole because the frame and cover are stuck and difficult to open and close. In this study, the design of a lifting mechanism was carried out to improve and integrate the locking type manhole. The mechanism of the locking manhole is that when the bolt located at the center is turned, the hub connected with the bolt descends, and the hook connected to the hub is rotated. The end of the hook is hooked to the manhole frame. The auxiliary device was installed on the hook so that the manhole cover can be lifted. The structure was designed to endure about 300kg of lifting force based on 70% of the yield stress of the hook to perform lifting function. The shape design was performed through the structural analysis using the finite element method. First, the basic design was performed with the simplified 2-dimensional model and the attachment position and shape were designed through the 3-dimensional model. In order to find out the structural problems of the designed shape, the scale downed model was fabricated through 3D printing and confirmed that the lifting function worked. Finally, it was confirmed that both the locking and the average lifting of about 6.1 mm can be done by applying the lifting mechanism through the machining and applying it to the existing locking manhole.

• Journal of Distribution Science
• /
• v.13 no.1
• /
• pp.27-33
• /
• 2015

Purpose - The ICT market in the EU is lagging behind that of the US; however, algorithm and software development within the EU have grown steadily, and they involve focusing on the creative cultural convergence conceptualized as part of Horizon 2020 and connecting neighboring markets in the EE and the Mediterranean region. It is essential to study the requirements to market the EU's creative ICT development in emerging industrial countries after examining its applicability in these countries. Research design, data, and methodology - This study deals with data pertaining to the EU's creative industry and competitive edge. The global cultural expansion of the EU facilitates a new concept involving not only low-cost IT products to enhance local cultural artifacts through R&D and the construction of efficient infrastructure services, but also information exchange with a realistic commercialization of the technology that can be applied for creative cultural localization. In the European industry, research on algorithms has been applied for the benefit of consumers. We investigated how the process is conducted in the EU. Results - Europe needs to adjust its economic structure to the local culture as part of IT distribution convergence. The convergence has been converted into a production algorithm with IT in the form of low-cost production. This is because there is an attempt to improve the quality of transport infrastructure, workforce availability, and the distribution of the distance to the local industries and consumers, using IT algorithms. Integrated into the manufacturing industry, based on the ICT infrastructure and solutions, smart localized regional clusters are formed with the help of grafting. Europe has own strategy to increase the number of hub-and-spoke cities. Europe is now becoming integrated, with an EPC system for regional cooperation rather than national competition in ICT technology. Europe has also been recognized in this study as changing the step-by-step paradigm for global competitiveness through new creative culture industries. Conclusions - As a result, there are several ways of converging with others through EU R&D intensity; therefore, the EU can be seen as successfully increasing marginal value, which is useful in developing a special industrial cluster or local cultural cities that create converged development by connecting people and objects with IT. In fact, when compared to the US, Europe has a strong culture and the car industries have a tendency to overshadow the IT industries with integration of services in IT distribution. Considering the rapid environmental changes, the convergence of IT services is likely to take place in Europe, similar to the pharmaceutical industry and the automotive industry. This requires a focus on human resources and automated systems management. The trend is to move away from low-wage industries, switched to key personnel centers of the local university-industry. EU emphasizes the creation of IT market demand in Europe involving local cultural convergence for marketing as the second step to strengthen the economic hub-and-spoke areas.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.8
• /
• pp.905-911
• /
• 2012

To establish a floating offshore wind turbine simulation model, a tension leg platform is added to an onshore wind turbine. The wind load is calculated by using meteorological administration data and a power law that defines the wind velocity according to the height from the sea surface. The wind load is applied to the blade and wind tower at a regular distance. The relative Morison equation is employed to generate the wave load. The rated rotor speed (18 rpm) is applied to the hub as a motion. The dynamic behavior of a 2-MW floating offshore wind turbine subjected to the wave excitation and wind load is analyzed. The flexible effects of the wind tower and the blade are analyzed. The flexible model of the wind tower and blade is established to examine the natural frequency of the TLP-type offshore wind turbine. To study the effect of the flexible tower and blade on the floating offshore wind turbine, we modeled the flexible tower model and flexible tower-blade model and compared it with a rigid model.