• 마이크로전자및패키징학회지
• /
• 제26권2호
• /
• pp.31-43
• /
• 2019

본 연구에서는 유연한 접속부를 갖는 유연전자 패키지 플립칩 접속을 위해 폴리머 탄성범프를 제작하였으며, 범프의 온도 및 하중에 따른 폴리머 탄성 범프의 점탄성 및 점소성 거동을 해석 및 실험적으로 분석하고 비교 평가하였다. 폴리머 탄성 범프는 하중에 의한 변형이 용이하여 범프 높이 평탄도 오차의 보정이 용이할 뿐만 아니라 소자가 형성된 칩에 가해지는 응력 집중이 감소하는 것을 확인하였다. 폴리머 탄성 범프의 과도한 변형에 따른 Au Metal Cap Crack 현상을 보완하여 $200{\mu}m$ 직경의 Spiral Cap Type, Spoke Cap type 폴리머 탄성 범프 형성 기술을 개발하였다. 제안된 Spoke Cap, Spiral Cap 폴리머 탄성 범프는 폴리머 범프 전체를 금속 배선이 덮고 있는 Metal Cap 범프에 비해 범프 변형에 의한 응력 발생이 적음을 확인할 수 있으며 이는 폴리머 범프 위의 금속 배선이 부분적으로 패터닝되어 있어 쉽게 변형될 수 있는 구조이므로 응력이 완화되는데 기인하는 것으로 판단된다. Spoke cap type 범프는 패드 접촉부와 전기적 접속을 하는 금속 배선 면적이 Spiral Cap type 범프에 비해 넓어 접촉 저항을 유지하면서 동시에 금속 배선에 응력 집중이 가장 낮은 결과를 확인하였다.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2000년도 2nd Korea-Japan Advanceed Semiconductor Packaging Technology Seminar
• /
• pp.7-38
• /
• 2000

Performance, reliability, form factor drive flip chip use. BGAs and CSPs will provide stepping stone to FC DCA .Growing vendor infrastructure - Low cost, high density organic substrates -New generations of fluxes and underfills .Adhesives flip chip technology as a low cost flip chip alternatives -Low cost Au stud or Electroless Ni bumps -Reliable thermal cycling and electrical performance.

• 마이크로전자및패키징학회지
• /
• 제22권3호
• /
• pp.19-23
• /
• 2015

본 연구에서는 COG (Chip On Glass) 패키지 적용을 위해 Au 범프를 전기도금 공정을 사용하여 Al/Si wafer와 SiN/Si wafer 위에 TiW/Au 구조를 갖는 두 종류의 Au범프 시료를 제작하였다. UBM (Under Bump Metallurgy) 물질로서 TiW 박막을 스퍼터링 방법으로 증착하였으며 스퍼터링 입력 파워(500~5000 Watt)에 따른 박리 현상을 관찰하였다. 안정된 계면 접착을 나타내는 스퍼터링 파워는 1500 Watt임을 확인 할 수 있었다. 또한 SAICAS (Surface And Interfacial Cutting Analysis System) 장비를 사용하여 기판 종류에 따른 Au Bump의 접착력을 조사하였다. TiW 증착 조건은 스퍼터링 파워를 1500 Watt로 고정하였다. TiW/Au 계면의 접착력은 두 종류의 wafer (Al/Si과 SiN/Si wafers)에 관계없이 오차 범위 안에서 비슷한 접착력을 보여주었으나, TiW UBM 스퍼터링 박막 계면에서의 접착력은 하부 박막인 Al 금속과 SiN 비금속 박막에서의 접착력 차이가 약 2.2배 크게 나타났다. 즉, Al/Si wafer와 SiN/Si wafer위에 증착된 TiW의 접착력은 각각 0.475 kN/m와 0.093 kN/m 값을 나타내었다.

• 마이크로전자및패키징학회지
• /
• 제25권4호
• /
• pp.155-161
• /
• 2018

강성도가 서로 다른 polydimethylsiloxane (PDMS) 탄성고분자와 flexible printed circuit board (FPCB)로 이루어진 PDMS/FPCB 구조의 강성도 국부변환 신축기판에 $100{\mu}m$ 직경의 Cu/Au 범프를 갖는 Si 칩을 anisotropic conductive adhesive (ACA)를 사용하여 플립칩 본딩 후, ACA내 전도성 입자에 따른 플립칩 접속저항을 비교하였다. Au 코팅된 폴리머 볼을 함유한 ACA를 사용하여 플립칩 본딩한 시편은 $43.2m{\Omega}$의 접속저항을 나타내었으며, SnBi 솔더입자를 함유한 ACA로 플립칩 본딩한 시편은 $36.2m{\Omega}$의 접속저항을 나타내었다. 반면에 Ni 입자를 함유한 ACA를 사용하여 플립칩 본딩한 시편에서는 전기적 open이 발생하였는데, 이는 ACA내 Ni 입자의 함유량이 부족하여 entrap된 Ni 입자가 하나도 없는 플립칩 접속부가 발생하였기 때문이다.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2000년도 Proceedings of 5th International Joint Symposium on Microeletronics and Packaging
• /
• pp.74-79
• /
• 2000

In an attempt to estimate the wetting properties of wettable metal layers by wetting balance method, an analysis of wetting curves of the coating layer was performed. Based on the analysis, wetting properties of UBM-coated Si-plate were estimated by the new wettability indices. The wetting curves of the one and both sides-coated UBM layers have the similar shape and show the similar tendency to the temperature. So the wetting property estimation of one side coating is possible with wetting balance method. For UBM of Si-chip, Cr/Cu/Au UBM is better than Ti/Ni/Au in the point of wetting time. At general reflow temperature, the wettability of high melting point solders(Sn-Sb, Sn-Ag) is better than that of few melting point ones(Sn-Bi, Sn-In).The contact angle of the one side coated plate to the solder can be calculated from the farce balance equation by measuring the static state force and the tilt angle.

• 한국재료학회지
• /
• 제12권9호
• /
• pp.750-760
• /
• 2002

In this study, three solders, Sn-37Pb, Sn-3.5Ag, and Sn-3.8Ag-0.7Cu were screen printed on both electroless Ni/Au and OSP metal finished micro-via PCBs (Printed Circuit Boards). The interfacial reaction between PCB metal pad finish materials and solder materials, and its effects on the solder bump joint mechanical reliability were investigated. The lead free solders formed a large amount of intermetallic compounds (IMC) than Sn-37Pb on both electroless Ni/Au and OSP (Organic Solderabilty Preservatives) finished PCBs during solder reflows because of the higher Sn content and higher reflow temperature. For OSP finish, scallop-like $Cu_{6}$ /$Sn_{5}$ and planar $Cu_3$Sn intermetallic compounds (IMC) were formed, and fracture occurred 100% within the solder regardless of reflow numbers and solder materials. Bump shear strength of lead free solders showed higher value than that of Sn-37Pb solder, because lead free solders are usually harder than eutectic Sn-37Pb solder. For Ni/Au finish, polygonal shaped $Ni_3$$Sn_4$ IMC and P-rich Ni layer were formed, and a brittle fracture at the Ni-Sn IMC layer or the interface between Ni-Sn intermetallic and P-rich Ni layer was observed after several reflows. Therefore, bump shear strength values of the Ni/Au finish are relatively lower than those of OSP finish. Especially, spalled IMCs at Sn-3.5Ag interface was observed after several reflow times. And, for the Sn-3.8Ag-0.7Cu solder case, the ternary Sn-Ni-Cu IMCs were observed. As a result, it was found that OSP finished PCB was a better choice for solders on PCB in terms of flip chip mechanical reliability.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.456-462
• /
• 2002

In the present work, a low cost and fine pitch bumping process by electroless Ni/immersion Au UBM (under bump metallurgy) and stencil printing for the solder bump on the Al pad is discussed. The Chip used this experimental had an array of pad 14x14 and zincate catalyst treatment is applied as the pretreatment of Al bond pad, it was shown that the second zincating process produced a dense continuous zincating layer compared to first zincating. Ni UBM was analyzed using Scanning electron microscopy, Energy dispersive x-ray, Atomic force microscopy, and X-ray diffractometer. The electroless Ni-P had amorphous structures in as-plated condition. and crystallized at 321 C to Ni and Ni$_3$P. Solder bumps are formed on without bridge or missing bump by stencil print solder bump process.

• Journal of Welding and Joining
• /
• 제21권5호
• /
• pp.534-539
• /
• 2003

An efficient soldering process using the longitudinal ultrasonic vibration is introduced in this work for electronic packaging. The effects of the process parameters such as the ultrasonic frequency, amplitude, dimension of the metal bump and solder are analyzed through a viscoelastic lumped model. The viscoelastic properties of the eutectic solder were measured for calculation and evaluation of heat generation capability of the solder. Experiments were conducted to verify the possibility of the proposed ultrasonic soldering method by inserting the Cu and Au bumps into the solder block. Localized heating due to ultrasonic vibration melts the solder near the metal bump, which demonstrates the applicability of the ultrasonic soldering method to the high-density electronic packaging.

• 마이크로전자및패키징학회지
• /
• 제24권2호
• /
• pp.61-67
• /
• 2017

소자의 트랜지스터 밀도가 급속히 높아짐에 따라 소자 내부에서 발생하는 열 유속(heat flux) 또한 빠르게 증가하고 있다. 소자의 고열 문제는 소자의 성능과 신뢰성 감소에 크게 영향을 미친다. 기존의 냉각방법들은 이러한 고열문제를 해결하기 위해선 한계점에 다다랐고, 그 대안으로 liquid heat pipe, thermoelectric cooler, thermal Si via, 등 여러 냉각방법이 연구되고 있다. 본 실험에서는 직선형 마이크로채널과 TSV(through Si via)를 이용한 액체 냉각시스템을 연구하였다. 두 종류의 냉매(DI water와 ethylene glycol(70 wt%))와 3 종류의 금속 범프(Ag, Cu, Cr/Au/Cu)의 영향을 분석하였으며, 대류, 복사 및 액체 냉각으로 인한 총 열 유속을 계산하여 비교하였다. 냉각 전후의 냉각시스템의 표면온도는 적외선현미경을 통해 측정하였고, 마이크로채널 내 액체 흐름은 형광현미경을 이용하여 측정하였다. 총 열 유속은 ethylene glycol(70 wt%)의 경우 가열 온도 $200^{\circ}C$에서 $2.42W/cm^2$로 나타났으며 대부분 액체 냉각 효과에 의한 결과로 확인되었다.

• 마이크로전자및패키징학회지
• /
• 제6권2호
• /
• pp.13-21
• /
• 1999

Flip chip assembly directly on organic boards offers miniaturization of package size as well as reduction in interconnection distances resulting in a high performance and cost-competitive Packaging method. This paper describes the investigation of alternative low cost flip-chip mounting processes using electroless Ni/Au bump and anisotropic conductive adhesives/films as an interconnection material on organic boards such as FR-4. As bumps for flip chip, electroless Ni/Au plating was performed and characterized in mechanical and metallurgical point of view. Effect of annealing on Ni bump characteristics informed that the formation of crystalline nickel with $Ni_3$P precipitation above $300^{\circ}C$ causes an increase of hardness and an increase of the intrinsic stress resulting in a reliability limitation. As an interconnection material, modified ACFs composed of nickel conductive fillers for electrical conductor and non-conductive inorganic fillers for modification of film properties such as coefficient of thermal expansion(CTE) and tensile strength were formulated for improved electrical and mechanical properties of ACF interconnection. The thermal fatigue life of ACA/F flip chip on organic board limited by the thermal expansion mismatch between the chip and the board could be increased by a modified ACA/F. Three ACF materials with different CTE values were prepared and bonded between Si chip and FR-4 board for the thermal strain measurement using moire interferometry. The thermal strain of ACF interconnection layer induced by temperature excursion of $80^{\circ}C$ was decreased with decreasing CTEs of ACF materials.