• 마이크로전자및패키징학회지
• /
• 제22권3호
• /
• pp.19-23
• /
• 2015

본 연구에서는 COG (Chip On Glass) 패키지 적용을 위해 Au 범프를 전기도금 공정을 사용하여 Al/Si wafer와 SiN/Si wafer 위에 TiW/Au 구조를 갖는 두 종류의 Au범프 시료를 제작하였다. UBM (Under Bump Metallurgy) 물질로서 TiW 박막을 스퍼터링 방법으로 증착하였으며 스퍼터링 입력 파워(500~5000 Watt)에 따른 박리 현상을 관찰하였다. 안정된 계면 접착을 나타내는 스퍼터링 파워는 1500 Watt임을 확인 할 수 있었다. 또한 SAICAS (Surface And Interfacial Cutting Analysis System) 장비를 사용하여 기판 종류에 따른 Au Bump의 접착력을 조사하였다. TiW 증착 조건은 스퍼터링 파워를 1500 Watt로 고정하였다. TiW/Au 계면의 접착력은 두 종류의 wafer (Al/Si과 SiN/Si wafers)에 관계없이 오차 범위 안에서 비슷한 접착력을 보여주었으나, TiW UBM 스퍼터링 박막 계면에서의 접착력은 하부 박막인 Al 금속과 SiN 비금속 박막에서의 접착력 차이가 약 2.2배 크게 나타났다. 즉, Al/Si wafer와 SiN/Si wafer위에 증착된 TiW의 접착력은 각각 0.475 kN/m와 0.093 kN/m 값을 나타내었다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.469-474
• /
• 2002

Laser and hot air reflow soldering of PBGA solder ball was investigated. Experimental results showed that surface quality and shear strength of solder bumps reflowed by laser was superior than the solder bumps reflowed by hot air, and the microstructure inside the solder bumps reflowed by laser was much finer. Analysis on interfacial reaction showed that eutectic solder reacted with Au/Ni/Cu pad shortly after the solder was melted. Interface of solder bump reflowed by laser consists of a continuous AuSn$_4$ layer and remnant Au element. Needle-like AuSn$_4$ grew sidewise from interface, and then spread out to the entire interface region. A thin layer of Ni$_3$Sn$_4$ intermetallic compound was found at the interface of solder bump reflowed by hot air, AuSn$_4$ particles distributed inside the whole solder bump randomly. It is the combination effect of the continuous AuSn$_4$ layer and finer eutectic microstructure inside the solder bump reflowed by laser that resulted in higher shear strength.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2003년도 기술심포지움 논문집
• /
• pp.68-71
• /
• 2003

The reaction of ultra-small eutectic 58Bl-42Sn solder bump with Au/Ni/Ti and Au/Cu/Ti UBMs during reflow was studied. The eutectic Bi-Sn solder bumps of $46{\mu}m$ diameter were fabricated by using the evaporation method and were reflowed using the rapid thermal annealing system. The intermetallic compound was characterized using a SEM, an EDS, and an XRD. The $(Cu_xAu_{1-x})_6Sn_5$ compounds formed at the interface between Bi-Sn solder and Au/Cu/Ti UBM. On the other hand, in the Bi-Sn solder bump on Au/Ni/Ti UBM, the faceted and rectangular intermetallic compounds were observed on the solder bump surface and inside the solder bump as well as at the UBM interface. These intermetallic compounds were Identified as $(Au_{l-x-y}Bi_xNi_y)Sn_2$ phase.

• Journal of Welding and Joining
• /
• 제22권1호
• /
• pp.65-70
• /
• 2004

A soldering process with longitudinal ultrasonic is conducted in this work using the Au bump and substrate. Localized heating of the solder is achieved and the stirring action due to the ultrasonic is found to influence the bond strength and microstructure of the eutectic solder The acceptable bonding condition is determined from the tensile strength. Since the multiple bonds can be formed simultaneously with localized heating, the proposed ultrasonic soldering method appears to be applicable to the high-density electronic package.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년 추계학술발표대회 개요집
• /
• pp.181-183
• /
• 2006

This paper studies the mechanical behaviors of Sn-3.5Ag solder joint against substrate(such as Au/Ni/Cu, Au/cu, Ni/Cu and Cu pad) after induction heating, a new soldering method. It was found that the solder bump formation depends on the time and current of the induction heating system. Also the heating value of the solder bump were found to vary with respect to the thermal conductivity of the pads on the substrate. In case of Au/Ni/Cu pad and Au/Cu pad, solder bump's shear strength were high for the heating time of $1.5{\sim}2sec$. For Ni/Cu pad, solder bump's shear strength were found to increase with time increment.

• 마이크로전자및패키징학회지
• /
• 제15권4호
• /
• pp.9-15
• /
• 2008

Au와 Sn을 순차적으로 도금한 Au/Sn 범프를 플립칩 본딩하여 Au-Sn 솔더 접속부를 형성 후, 미세구조와 접속저항을 분석하였다. $285^{\circ}C$에서 30초간 플립칩 본딩한 Au-Sn 솔더 접속부는 $Au_5Sn$+AuSn lamellar 구조로 이루어져 있으며, 이 시편을 $310^{\circ}C$에서 3분간 유지하여 2차 리플로우시 $Au_5Sn$+AuSn interlamellar spacing이 증가하였다. $285^{\circ}C$에서 30초간 플립칩 본딩한 Au-Sn 접속부는 15.6 $m{\Omega}$/bump의 평균 접속저항을 나타내었으며, 이 시편을 다시 $310^{\circ}C$에서 3분간 유지하여 2차 리플로우 한 Au-Sn 접속부는 15.0 $m{\Omega}$/bump의 평균 접속저항을 나타내었다.

• Journal of Welding and Joining
• /
• 제22권3호
• /
• pp.62-68
• /
• 2004

The strip Au bumps are bonded using longitudinal ultrasonic far the electronic package. Au bumps on the chip and substrate are aligned in a crossed shape, and the ultrasonic is imposed on the chip to form the solid-state bond between the Au bumps. Deformed bump shapes are calculated using the finite element method, and the bond strength is measured experimentally. The crossed strip Au bumps are deformed similar to the saddle, which provides larger contact surface area and higher friction force. Compared with the previous bonding method between the Au bump and planar pad, higher bond strength is obtained using the crossed strip bumps.

• Journal of Welding and Joining
• /
• 제29권6호
• /
• pp.65-70
• /
• 2011

The effect of flip chip bonding parameters on formation of intermetallic compounds (IMCs) between Au stud bumps and Sn-3.5Ag solder was investigated. In this study, flip chip bonding temperature was performed at $260^{\circ}C$ and $300^{\circ}C$ with various bonding times of 5, 10, and 20 sec. AuSn, $AuSn_2$ and $AuSn_4$ IMCs were formed at the interface of joints and (Au, Cu)$_6Sn_5$ IMC was observed near Cu pad side in the joint. At bonding temperature of $260^{\circ}C$, $AuSn_4$ IMC was dominant in the joint compared to other Au-Sn IMCs as bonding time increased. At bonding temperature of $300^{\circ}C$, $AuSn_2$ IMC clusters, which were surrounded by $AuSn_4$ IMC, were observed in the solder joint due to fast diffusivity of Au to molten solder with increased bonding temperature. Bond strength of Au stud bump joined with Sn-3.5Ag solder was about 23 gf/bump and fracture mode of the joint was intergranular fracture between $AuSn_2$ and $AuSn_4$ IMCs regardless bonding conditions.

• 마이크로전자및패키징학회지
• /
• 제17권2호
• /
• pp.55-61
• /
• 2010

탄탈륨실리사이드 히터가 내장된 소자를 Ag 페이스트와 Au SBB(Stud Bump Bonding)를 이용하여 Au가 코팅 된 기판에 각각 접합 하였다. 전단 테스트와 전류를 흐르면서 열 성능을 측정하였다. Au 스터드 범프 본딩의 최적 플립칩 접합조건은 전단 후 파괴면 관찰하여 설정하였으며, 기판 온도를 $350^{\circ}C$, 소자 온도를 $250^{\circ}C$에서 하중을 300 g/bump 로 하여 접합하는 경우가 최적 조건이였다. 히터에 5 W 인가시 소자의 온도는 Ag 페이스트를 이용한 접합의 경우 최대 온도는 약 $50^{\circ}C$이었으며, Au 금속층을 갖고 있는 실리콘 기판에 Au 스터드 본딩으로 접합된 인 경우 약 $64^{\circ}C$를 나타내었다. 기판과의 접촉면적이 와이어본딩과 Au 스터드 범프 본딩 가 약 300배가 차이가 나는 경우 약 $14^{\circ}C$ 차이를 나타내었고, 전사모사를 통하여 접합면의 접촉저항이 중요한 이유임을 알 수 있었다.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1995년도 추계 학술발표 강연 및 논문개요집
• /
• pp.82-82
• /
• 1995