• Journal of the Korean Ceramic Society
• /
• v.50 no.5
• /
• pp.348-352
• /
• 2013

The evaluation of plasma resistance and the characteristics of yttria ceramics fabricated by calcination yttria as a starting material without dopants under an oxidation atmosphere was investigated. Regardless of the starting materials, as-received, and calcined yttria powder, XRD patterns showed that all samples have $Y_2O_3$ phase. The three cycling process inhibited a large grain, which occurs frequently during the yttria sintering, and a high density ceramic with a homogeneous grain size was obtained. The grain size of the sintered ceramic was affected by the starting powders. The smaller the grain size, the larger were the Young's modulus and KIC. Compared to $Al_2O_3$ and $ZrO_2$ ceramics, yttria ceramics showed a 3 times larger plasma resistance and a 1.4~2.2 times lower weight loss during the plasma etching test, respectively.

• Journal of the Korean Ceramic Society
• /
• v.53 no.3
• /
• pp.332-337
• /
• 2016

As a case study on yttria stabilized zirconia ceramics, the sintering characteristics of submicron powders and the granulation prepared by two-fluid spray drying of submicron particles were investigated. As-received powders of yttria stabilized zirconia particles were reduced to a uniform size of less than about 200 nm by repeated milling. Granulation size obtained by the two-fluid spray drying was affected by the organic matter and the primary particle size. Sintering behavior such as porosity, water absorption ratio, density, and transparency was influenced by processing conditions of the powder, and the discontinuous interfaces in a green body were reduced.

• Journal of the Korean Vacuum Society
• /
• v.6 no.S1
• /
• pp.160-165
• /
• 1997

Yttria stabilized zirconia coating is an attractive material for several engineering applications. In order to produce coatings with consistent and reliable performance it is important to understand the influence of spraying parameters on the coating properties and optimize the spraying parameters. In this paper the low pressure plasma spray(LPPS) deposition of as-received zirconia powder has been investigated using simple one-factor-at-a-time approach. The deposition efficiency was chosen to evaluate the melting characteristics of the as-received zirconia powder. The results obtained indicated that the deposition efficiency of zirconia powder is very sensitive to the spraying parameters such as plasma gas flow rate and ranges from 24% to 57% The microstructure and the phase composition of zirconia coating deposited with the different plasma spraying parameters were also examined by SEM and XRD respectively. The relationship between deposition efficiency and the microstructure of zirconia coating was discussed.

• Journal of the Korean Ceramic Society
• /
• v.38 no.11
• /
• pp.987-992
• /
• 2001

A refractory grade low-cost silicon nitride powder was chemically analyzed, purified, and gas pressure sintered with the sintering additives. As-received powder contained a significant amount of free-Si, 0.72 wt% of Fe, 0.5 wt% of al and 0.31 wt% of Ca. Oxygen and carbon contents of the powder were 3.3 wt% and 0.4 wt%, respectively, and it consisted of 96% of $\beta$-phase and 4% of $\alpha$-phase. After lowering the Fe content and nitriding treatment, the powder was sintered with 6 wt% yttria and 2 wt% alumina for 1 h between 1823 K and 2123 K in order to examine the sintering behavior. Fully dense samples were obtained by sintering at 2123k for 2h. For comparison, a commercially available high-grade powder was also sintered at the same time. The low-cost powder showed much slower densification rate than the high-grade powder. Fully dense sample prepared from the low-cost powder contained a number of coarse grains with a low aspect ratio, and its hardness, fracture toughness, flexural strength and thermal shock resistance were not as good as those of the sample prepared with the high-grade powder.

• Journal of Applied Reliability
• /
• v.15 no.3
• /
• pp.216-221
• /
• 2015

Sintering behavior of 3%yttria-stabilized zirconia was comparatively studied using a spray-dried powder produced by a domestic and global company. Quality of the sintered block was analysed in terms of relative density, shrinkage rate, grain growth, hardness, and fracture toughness. Relative density, shrinkage rate, and hardness value of the finally sintered block was similar between domestic and global zirconia powder, respectively. But, flexural strength of the domestic powder specimen was about 70% of the sintered block produced by using a global powder. The poor sintering quality of the domestic powder was discussed in relation with compressibility of the spray-dried granule-type powder and the amount of monoclinic phase in the as-received powder.

• Journal of Ceramic Processing Research
• /
• v.19 no.6
• /
• pp.450-454
• /
• 2018

In recent years, thermal insulation coating technology for automotive engine parts has received significant attention as a means of improving the thermal efficiency of automotive engines. One of the characteristics of thermal insulation coatings is their low thermal conductivity, and, materials such as YSZ (Yttria-stabilized zirconia), which have low thermal conductivity, are used for this purpose. This research presents a study of the changes in the microstructure and thermal conductivity of $8YSZ/SiO_2$ multi compositional thermal insulation coating for different compositions, and particle size distributions of suspension, when it is subjected to suspension plasma spraying. To obtain a porous coating structure, the mixing ratio of 8YSZ and $SiO_2$ particles and the particle sizes of the $SiO_2$ were changed. The microstructure, phase formation behavior, porosity and thermal conductivity of the coatings were analyzed. The porosities were found to be 1.2-32.1%, and the thermal conductivities of the coatings were 0.797-0.369 W/mK. The results of the study showed that the microstructures of the coatings were strongly influenced by the particle size distributions, and that the thermal conductivities of the coatings were greatly impacted by the microstructures of the coatings.