• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.9
• /
• pp.155-163
• /
• 2012

The geometrical and electrical errors of array sensors can severely degrade the performance of array sensor system. Various calibration techniques are developed to alleviate this problem. In this paper, two different calibration methods with respect to location, gain and phase of array sensors are presented. One method applies the first-order Taylor series expansion to approximate the true steering vector from the nominal values of array sensors. Then a set of equations is formed by using the null characteristics of the MUSIC spectrum to estimate errors of location, gain and phase of array sensors. Another method estimates these errors based on the data covariance matrix of pilot sources. From the simulations, it is demonstrated that two calibration algorithms calibrated an array system successfully. In addition to that, Fistas and Manikas's algorithm is more robust against noise than Ng and Lie's one when SNR is from 10dB to 50dB.

• Journal of Positioning, Navigation, and Timing
• /
• v.6 no.2
• /
• pp.43-51
• /
• 2017

In this study, the effect of the steering vector model mismatch due to array uncertainties on the performance of array processing was analyzed through simulation, along with the alleviation of the model mismatch effect depending on array calibration. To increase the reliability of the simulation results, the actual steering vector of the array antenna obtained by electromagnetic simulation was used along with the Jahn's channel model, which is an experimental channel model. Based on the analysis of the power spectrum for each direction, beam pattern, and the signal-to-interference-plus-noise ratio of the beamformer output, the performance deterioration of array processing due to array uncertainties was examined, and the performance improvement of array processing through array calibration was also examined.

• Proceedings of the KSRS Conference
• /
• 2004.10a
• /
• pp.577-580
• /
• 2004

To overcome with large size noise source distribution network design difficulty in interferometric radiometer system, especially for sub-Y-type array, a new on-board calibration technique using noise re-radiation is proposed in this paper. The suggested calibration technique is using noise re-radiation effect of center antenna after noise source injection from matched load. This approach is especially proper to sub-Y-type array interferometric synthetic aperture radiometer in mm-wave frequency band. Compared with noise injection network of a conventional synthetic aperture radiometer, the system mass, volume, and hardware complexity is reduced and cost-effective. Only one internal noise source, matched load, is used for injection using noise re-radiation technique a small set of sub-Y receiver channels is calibrated. Detailed calibration scenario is discussed and simulation results about noise re­radiation effect are presented.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.5
• /
• pp.162-170
• /
• 2022

In this paper, the phased-array transceiver (TRX) channel amplitude and phase calibration method for a radar wind profiler (RWP) based on the 256 active phased array is discussed. Without the additional module, the TX and RX calibration paths were secured using couplers and switches in the TRX front ends and the TRX switching duplexers, and the amplitude and phase of the 256 TRX were calibrated using a gain and phase detector. The beam widths and side lobes of five beams (vertical, east, west, south, and north) of the calibrated 256 active phased array antenna were confirmed by a near-field which agreed well with the simulation results. The proposed calibration method can be easily applied to a system based on an active phased array operated in an outdoor environment.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.2A
• /
• pp.139-146
• /
• 2009

This paper presents an average internal loop-back antenna calibration method for array antenna in TDD(Time Division Duplex) systems. The proposed method calibrates the amplitude and the phase of RF systems using into mal coupler and switches without aids of external calibration systems. The average calibration scheme of the proposed method also increases reliability of calibration performance. Computer simulation demonstrates that the proposed method corrects beamforming angles of DOA estimation algorithm and BER performance in transmit power allocation scheme.

• Journal of Satellite, Information and Communications
• /
• v.10 no.4
• /
• pp.46-51
• /
• 2015

In this paper, I design a linear array antenna simulator for anti-jamming GPS systems and perform various performance analysis by simulation. First, I generate simulated transmission signals through the analysis of GPS satellite signal structure, and analyze SNR(Signal to Noise power Ratio) performance of linear array antenna according to number of arrays under noise environments. In addition, I analyze the performance of the anti-jamming beam pattern using MMSE(Minimum Mean Square Error) signal processing method, and also analyze the anti-jamming performance considering antenna calibration problem when there are different delays between arrays.

• The Journal of the Acoustical Society of Korea
• /
• v.23 no.5
• /
• pp.370-375
• /
• 2004

This paper proposes an algorithm that estimates three dimensional array shape calibration about the bottom-mounted sensor array. under the assumption that the active sources are in the far-field with unknown positions. Under some assumptions. we calculate the sensor positions via an algebraic solutions of a least squares problem that the linear equations are related to the sensor positions and directions or arrival. We give examples of algorithm performance from both computer simulations and sea test. We also illustrate the performance of sensor positions estimation as a function of time delay estimation variance and the distribution of the localizing sources.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.579-580
• /
• 2008

DRAM설계시 DDR2에서부터 고속 동작으로 인해 반송파에 의한 신호외곡으로 impedance matching의 필요성이 대두되었다. 이로 인해 제안된 방법은 외부 Termination 저항(RZQ)을 기준으로 impedance matching을 위한 Rtt 저항의 생성이다.[1] 제안된 ZQ Calibration 회로는 기존의conventional ZQ Calibration 회로에 After ZQ calibration block을 추가하여 한 번 더 교정함으로써 마지막 PMOS Array와 NMOS Array 저항 값이 Termination 저항 값에 가깝도록 설계하였다. 따라 전력효율은 그대로 유지하면서 ${\Delta}VM$의 오차범위를 기존의 ${\pm}5%$이내에서 skew 조건에 따라 ${\pm}1.33%$까지 향상시키는 것을 볼 수 있다. (JEDEC spec. ${\pm}5%$이내).

• Analytical Science and Technology
• /
• v.16 no.2
• /
• pp.95-101
• /
• 2003

In this study, water content in the mixture of methanol and ethanol was nondestructively measured by near infrared (NIR) spectroscopy. Two types of NIR instruments, portable NIR system with a photo-diode array and scanning type NIR spectrometer were used and the calibration results were compared. Partial least squares regression (PLSR) was applied for the calibration and validation for the quantitative analysis. The calibration results from both instruments showed good correlation with actual values. The calibration with the use of PLS model predicted water concentration with a standard error of prediction (SEP) of 0.10% and 0.12% for photo diode array and scanning type, respectively. During 6 days, routine analyses for 3%, 5% and 7% water in ethanol solution with 2% methanol were performed to validate the robustness of the developed calibration model. The routine analyses showed good results with coefficient of variation (CV) of within 3% for both types of NIR spectrometers. This study showed that the rapid determination of water in the mixture of methanol and ethanol was successfully performed by NIR spectroscopy and the performance of the portable NIR system with a photo diode array detector was comparable to that of the scanning type NIR spectrometer.

• Proceedings of the IEEK Conference
• /
• 2002.07a
• /
• pp.519-522
• /
• 2002

An active phased array antenna consists of many channels. Each channel has a different initial phase shift and gain because of the inequality in the active circuits themselves, interface between radiators and active circuits, and beam-forming circuits and other antenna system configurations. This raises an inherent problem in active phased array antennas. To compensate for this problem the initial phase and gain of each channel should be calibrated. This paper presents an efficient calibration method for an initial phase variation of each channel in active phased array antennas. We tested our method in an active phased array antenna, and obtained good results in the radiation pattern and beam direction of antenna.