• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.1
• /
• pp.153-161
• /
• 1993

Heat transfer processes in the combustion chamber of a pebble bed regenerative heat exchanger for MHD power generation has been analyzed numerically for heating, evacuation argon heating periods individually. The calculated result well explain the measured temperature change at the top of the pebble bed. The analytical result point out that the length of evacution period and the geometry optimization both for the combustion chamber and the heat storage bed are very important factors for the improvement of thermal performance in MHD power generation.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.197-200
• /
• 2008

The existing computer code to solve the air flow in a segmented constrictor-type arc-heated wind tunnel named ARCFLO4 is improved to accept an air-argon mixture as the working gas and to consider the separated injection of air and argon. The new version of the code is used to calculate the flows in the Aerodynamic Heating Facility of NASA Ames Research Center where argon concentration is relatively high. The calculation shows that argon tends to increase the diameter of the arc-column, increase ionization fraction, decrease thermal efficiency of the arc-heater, and push the ratio of the centerline-to-average enthalpy toward unity. The calculated operating characteristics of the arc-heater agree well with the experimental data.

• The Journal of Korean Academy of Prosthodontics
• /
• v.35 no.3
• /
• pp.566-576
• /
• 1997

This study was performed to evaluate the tensile strength of solder joint in titanium and the wettability of 14K gold solder on titanium. Two pieces of titanium rod 30 mm in length and 3mm in diameter were butt-soldered with a 14K gold solder using the electric resistance heating under flux-argon atmosphere, the infrared heating under argon atmosphere, and the infrared heating under vacuum-argon atmosphere. A tensile test was performed at a crosshead speed of 0.5 mm/min, and fracture surfaces were examined by SEM. To evaluate the wettability of 14K gold solder on titanium, titanum plates of a $17{\times}17{\times}1mm$ were polished with #80-#2000 emery papers, and the spreading areas of solder 10 mg were measured by heating at 840 * for 60 seconds. The solder-matrix interface regions were etched by the solution of 10% KCN-10% (NH4)2S2O8, and analyzed by EPMA. The results obtained were summarized as follows ; 1. The maximum tensile strength was obtained when the titanium surface was polished with #2000 emery paper and soldered using the electric resistance heating under flux-argon atmosphere. Soldering strengths showed the significant difference between the electric resistance heating and the infrared heating(p<0.05). 3. The fracture surfaces showed the aspect of brittle fracture, and the failure developed along the interfaces of solder-matrix reaction zone. 4. The EPMA data for the solder-matrix interface region revealed that the diffusion of Au and Cu occurred to the titanium matrix, and the reaction zone showed the higher contents of Au, Cu and Ti than others.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.746-751
• /
• 2002

In order to make clear the physical relation among the arc plasma, the anode heat transfer and the weld penetration, the results of experimental measurements of temperatures of arc plasma, the distributions of heat input and current on the anode and the weld penetration were presented The experimental results showed that the electron temperature above the anode and current and heat input density on the anode was dominated by the position of the cathode. Furthermore, it was showed that electron temperature of arc plasma was dominated by the cathode shape. These results were related with the results of the welded penetration measurements. As a result, it was showed that the electron temperature above the anode and current density distribution on the anode decided the heat input density distribution on the anode and that the heat input density on the anode remarkably dominated the size of the weld penetration in argon GTA welding process. Furthermore, it was suggested that the cathode played the important role in the determination of the weld penetration in argon GTA welding process.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.1
• /
• pp.73-77
• /
• 2021

In this study, we report on the effects of argon plasma treatment on Ag nanowires by varying the power and duration. Sheet resistance was found to be significantly reduced to 10 ohm/sq. relative to the value of 21 ohm/sq. for the pristine sample. Such a reduction was found to be associated with welded junctions between Ag nanowires, which results in enhanced current flow. With the optimized plasma treatment conditions, the maximum and average transmittance were 76.8% and 71%, respectively. Finally, we fabricated transparent heating devices based on the methodology, which exhibited superior heating capability.

• Journal of Surface Science and Engineering
• /
• v.29 no.5
• /
• pp.593-598
• /
• 1996

Previously, in trying to prepare perovskite type oxide powders by microwave heating, we found out a non-equilibrium argon plasma is generated around the powders and discharge continues stable at atmospheric pressure. In this study, we tried the plasma decomposition of heat-stable higher organic compound such as palmitic acid which is the principal constituent of the fimger fats. It was proved that suitable amount of coexistence of oxygen radicals into the argon flow accelerates the decomposition of palmitic acid. The argon-oxygen mixed gas plasma was able to perform a complete elimination of higher organic compound.

• Journal of Sensor Science and Technology
• /
• v.17 no.3
• /
• pp.188-194
• /
• 2008

For the accurate calibrations of thermometers at low temperatures, triple points of oxygen and argon have been realized using sealed-type triple point cells. The triple points were realized with both adiabatic and continuous heating methods. The resistance of three capsule-type standard platinum resistance thermometers were measured at the triple points of oxygen, argon, mercury and water for the calibrations of these thermometers in the range from $-220^{\circ}C$ to $0.01^{\circ}C$. The extended uncertainty, with the coverage factor of 2, of the calibration in this range is smaller than 1 mK.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.9 s.252
• /
• pp.1148-1153
• /
• 2006

This paper deals with the effect of the direct heating method(DHM) for straightening the micro wire. Straightened micro wires have been widely used in the fields of the medicine and the semi-conductor. We have developed a micro wire straightening system by using the direct wire heating method. To controling the tension of the micro wire during the heating and straightening process, a precision tension sensor was set up. In order to avoid the surface oxidation during the heating process, the argon inert gas was supplied to the vicinity of the wire. And, this paper shows the correlation between the tension and the current when arson gas supplied to the tungsten wire. Through several experiments, the optimal tension and current were found. Also, higher straightness $({\approx}1{\mu}m/1000{\mu}m)$ and roundness$(<{\Phi}{\pm}2{\mu}m/100{\mu}m)$ founded when $500{\mu}600gf$ tension and 1.5 ampere.

• YAKHAK HOEJI
• /
• v.37 no.1
• /
• pp.76-83
• /
• 1993

The changes in discharge current, emission and/or oscillation frequency of the electric oscillation of a glow discharge are the potential sensitive measure of the concentration of an impurity in the argon plasma supporting gas. A single jet enhanced glow discharge has been interfaced with the gas chromatograph via 1/8" O.D. tube with a heating pad to study the changes in discharge current. To investigate the optimum operating conditions of the glow discharge system as detector for gas chromatography, pressure, gas flow rate, discharge current, distance between the anode and the cathode have been studied.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.12
• /
• pp.883-888
• /
• 2007

As a starting point of investigating what molecular dynamic simulations can reveal about the nature of atomic level of heating and cooling process, argon described by the LJ potential is considered. Stepwise heating and cooling of constant rates are simulated in the NPT (constant number, pressure and temperature) ensemble. Hysteresis is found due to the superheating and supercooling. Drastic change of volume and energy is involved with phase change, but the melting point can not be obtained by simply observing the changes of these quantities. Since liquid and solid phases can co-exist at the same temperature, Gibbs free energy should be calculated to find the temperature where the Gibbs free energy of liquid is equal to that of the solid since the equilibrium state is the state of minimum Gibbs free energy. The obtained melting temperature, $T^*=0.685$, is close to that of the experiment with only 2% error.