• Journal of the Korean Vacuum Society
• /
• v.19 no.3
• /
• pp.206-210
• /
• 2010

Al-doped ZnO thin films were deposited with various Ar flow rate by RF magnetron sputtering, and theire properties were studied. A high-quality thin film was obtained by controlling the Ar flow rate, and the influence of the Ar flow rate on the Al-doped ZnO thin film was confirmed. In all Al-doped ZnO thin films, light transmittance had above 80%. Through Hall measurement and X-ray photoelectron spectrometer, the sample of 60 sccm, which had the lowest resistivity, showed the lower Al concentration. This result was attributed to oxygen vacancy rather than Al concentration.

• Korean Chemical Engineering Research
• /
• v.51 no.6
• /
• pp.755-759
• /
• 2013

The etch rate and etch profile of Si was investigated when Ar was added to an $SF_6$ plasma in the etch step of the Bosch process. A Si substrate was etched with the Bosch process using $SF_6$ and $SF_6$/Ar plasmas, respectively, in the etch step to analyze the effects of Ar addition on the etch characteristics of Si. When the Ar flow rate in the $SF_6$ plasma was increased, the etch rate of the Si substrate increased, had a maximum at 20% of the Ar flow rate, and then decreased. This was because the addition of Ar to the $SF_6$ plasma in the etch step of the Bosch process resulted in the bombardment of Ar ions on the Si substrate. This enhanced the chemical reactions (thus etch rates) between F radicals and Si as well as led to sputtering of Si particles. Consequently, the etch rate was higher more than 10% and the etch profile was more anisotropic when the Si substrate was etched with the Bosch process using a $SF_6$/Ar (20% of Ar flow rate) plasma during the etch step. This work revealed a feasibility to improve the etch rate and anisotropic etch profile of Si performed with the Bosch process.

• Applied Science and Convergence Technology
• /
• v.25 no.6
• /
• pp.145-148
• /
• 2016

This paper, Al-doped ZnO(AZO) thin films for application as transparent conducting oxide films were deposited on the Corning glass substrate by using RF magnetron sputtering system. The effects of various Argon gas flow rates on optical and electrical characteristics of AZO films were investigate sputtering method. The Carrier Concentration is enhanced as Ar gas rate increases, and also the oxygen vacancy concentration. The figure of merit obtained in this study means that AZO films which deposited Ar gas rate of 75 sccm have the highest Carrier concentration and Hall mobility, which have the highest photoelectrical performance that it could be used as transparent electrodes.

• Journal of the Korean institute of surface engineering
• /
• v.39 no.3
• /
• pp.137-141
• /
• 2006

Process window for infinite etch selectivity of silicon nitride $(Si_3N_4)$ layers to ArF photoresist (PR) was investigated in dual frequency superimposed capacitive coupled plasma (DFS-CCP) by varying the process parameters such as low frequency power $(P_{LF})$, $CH_2F_2$ and $H_2$ flow rate in $CH_2F_2/H_2/Ar$ plasma. It was found that infinite etch selectivities of $Si_3N_4$ layers to the ArF PR on both blanket and patterned wafers can be obtained for certain gas flow conditions. The etch selectivity was increased to the infinite values as the $CH_2F_2$ flow rate increases, while it was decreased from the infinite etch selectivity as the $H_2$ flow rate increased. The preferential chemical reaction of the hydrogen with the carbon in the polymer film and the nitrogen on the $Si_3N_4$ surface leading to the formation of HCN etch by-products results in a thinner steady-state polymer and, in turn, to continuous $Si_3N_4$ etching, due to enhanced $SiF_4$ formation, while the polymer was deposited on the ArF photoresist surface.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.139.2-139.2
• /
• 2013

6" Multi-crystal Silicon wafer has etched suing a remote - type RF Dielectric barrier discharge (RF DBD) at atmospheric pressure. DBD source is composed of Al electrode and coated Al2O3 dielectric as function of Ar/NF3 gas combination and input power used 13.56 MHz power supply. Ar gas flow rate is changed from 2 to 10 Slm, and NF3 flow rate is changed from 0.2~1 slm. At the result, NF3 flow rate Si etching rate also increase whit the increasing of NF3 flow rate But at 2 slm etching rate was decrease. In this experience, Max etching rate is 2.3 ${\mu}m/min$ when the scan time is 45 sec.

• Journal of the Korean institute of surface engineering
• /
• v.35 no.2
• /
• pp.113-121
• /
• 2002

We have investigated insulating properties of $SiO_2$ interlayer for the thin film strain gauge, which were prepared by RF magnetron sputtering method in various deposition conditions, such as Ar pressure, gas flow rates and sputtering gases. SEM, AFM and FT-IR techniques were used to analyze its structures and composition. As the Ar pressure and the flow rate increased, the insulating interlayer showed low insulating resistance due to its porous structure and defects. Oxygen deficiency in $SiO_2$ was decreased as fabricated by hydrogen reactive sputtering. We could enhance the surface mobility of sputtered adatoms by using Ar/$H_2$ sputtering gas and obtain a good surface roughness and insulating property. The optimum insulating resistance of 9.22 G$\Omega$ was obtained in Ar/30% $H_2$ mixed gas, flow rate 10sccm, and 1mTorr.

• Transactions on Electrical and Electronic Materials
• /
• v.10 no.6
• /
• pp.203-207
• /
• 2009

We have investigated the effect of ambient gases on the structural, electrical, and optical characteristics of ITO thin films intended for use as anode contacts in OLED (organic light emitting diodes) devices. These ITO thin films are deposited by radio frequency (RF) magnetron sputtering under different ambient gases (Ar, Ar+$O_2$, and Ar+$H_2$) at $300{^{\circ}C}$. In order to investigate the influences of the oxygen and hydrogen, the flow rate of oxygen and hydrogen in argon mixing gas has been changed from 0.5 sccm to 5 sccm and from 0.01 sccm to 0.25 sccm, respectively. The intensity of the (400) peak in the ITO thin films increased with increasing $O_2$, flow rate whilst the (400) peak was nearly invisible in an atmosphere of Ar+$H_2$. The electrical resistivity of the ITO thin films increased with increasing $O_2$ flow rate, whereas the electrical resistivity decreased sharply under an Ar+$H_2$ atmosphere and was nearly similar regardless of the $H_2$ flow rate. The change of electrical resistivity with changes in the ambient gas composition was mainly interpreted in terms of the charge carrier mobility rather than the charge carrier concentration. All the films showed an average transmittance of over 80% in the visible range. The OLED device was fabricated with different ITO substrates made with the configuration of ITO/$\alpha$-NPD/DPVB/$Alq_3$/LiF/Al in order to elucidate the performance of the ITO substrate. Current density and luminance of OLED devices with ITO thin films deposited in Ar+$H_2$ ambient gas is the highest among all the ITO thin films.

• Journal of the Korean Ceramic Society
• /
• v.40 no.12
• /
• pp.1165-1169
• /
• 2003

The Ta$_2$O$_{5}$ thin film was deposited on Si-(III) and glass substrate with the change of Ar:O$_2$ gas flow rate in the assist ion gun by the Dual ion-Beam Sputtering (DIBS). As the $O_2$ gas flow of the assist ion gun was decreased, the deposition rate of the thin films decreased. The refractive index was fixed (2.11, at 1550 nm) without regarding to $O_2$ gas flow of the range 3∼12 sccm in assist ion gun. The condition of Ar:O$_2$=3:12 was formatted stoichiometry composition of Ta$_2$O$_{5}$ and the ms roughness was small (0.183 nm).

• Journal of Korea Foundry Society
• /
• v.32 no.6
• /
• pp.276-283
• /
• 2012

This study presents the results on the changes of crucible thermal conductivity and inflow of Ar, and constructed the mathematical model about heat transfer into furnace. As process variables, simulation model was designated thermal conductivity of crucible to $0.5W{\cdot}m^{-1}{\cdot}K^{-1}$, $1W{\cdot}m^{-1}{\cdot}K^{-1}$, $2W{\cdot}m^{-1}{\cdot}K^{-1}$, $4W{\cdot}m^{-1}{\cdot}K^{-1}$, and inflow rate of Ar to 15 L/min, 30 L/min, 60 L/min. Initial condition and boundary condition were set respectively in two terms of process. Each initial conditions were set up by the preceding simulation of heat and fluid flow. The primary goal is the application of unidirectional growth of Si ingot using the result. In the result of the change of heat conductivity of crucible, the higher thermal conductivity of crucible shows the shorter solidification time and the bigger temperature difference. And the flow patterns are changed with the inflow rate of Ar. Finally, we found that the lower crucible's thermal conductivity, the better crucible is at polycrystalline Si ingot growth. But in case of Ar inflow, it is hard to say about good condition. This data will be evaluated as useful reference used in allied study or process variable control of production facilities.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2011.04a
• /
• pp.717-720
• /
• 2011

고속 네트워크 환경에서 AR UDT(Adaptive Rate control UDT)는 표준 전송 프로토콜인 TCP에 비해 뛰어난 성능을 보인다. UDT(UDP-based Data Transfer)를 기반으로 하는 AR UDT의 혼잡제어는 네트워크 상태를 예측하여 패킷 간 전송시간을 변화시킴으로써 기존 UDT보다 향상된 성능을 보인다. 그러나 AR UDT는 네트워크 상태 예측의 오차가 클 뿐만 아니라 rate control만을 공격적으로 조절하기 때문에 수신 버퍼의 초과로 인해 안정적인 성능을 기대하기 어렵다. 본 논문에서는 AR UDT환경에서 네트워크 상태에 따라 적응적으로 혼잡제어를 하는 기법을 제안한다. RTT(Round Trip Time)의 변화량에 따라 네트워크 상태를 예측하여 flow control과 rate control을 적응적으로 조절한다. 네트워크 시뮬레이션 결과를 통하여 AR UDT에 비해 전송속도와 안정성이 향상되었음을 보였다.