• Transactions on Electrical and Electronic Materials
• /
• v.17 no.2
• /
• pp.104-108
• /
• 2016

To research the correlation between oxygen vacancy and the electrical characteristics of ZTO, which is made by using a target mixed ZnO:SnO₂=1:1, the ZnO, SnO₂ and ZTO were analyzed by PL, XPS, XRD patterns and electrical properties. It was compared with the electron orbital spectra of O 1s in accordance with the electrical characteristics of ZnO, SnO₂ and ZTO. The electrical characteristics of ZTO were improved by increasing the annealing temperatures, due to the high degree of crystal structures at a high temperature, and the physical properties of ZTO was similar to that of ZnO. The amorphous structure of SnO₂ was increased with increasing the temperature. The Schottky contact of oxide semiconductors was formed using the depletion region, which is increased by the electron-hole combination due to the annealing processes. ZnO showed the Ohmic contact in spite of a high annealing temperature, but SnO₂ and ZTO had Schottky contact. As such, it was confirmed that the electrical properties of ZTO are affected by the molecules of SnO₂.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1203-1207
• /
• 2008

For a large sized, ultra definition (UD) and high refresh rate for motion blur free AMLCD TVs, amorphous IGZO thin film transistor (TFT) are applied and investigated in terms of threshold voltage ($V_{th}$) shift influenced by active layer thickness uniformity, source drain etching technology, heat treatment and passivation condition. Optimizing above parameters, we fabricated the world's largest 15 inch XGA AMLCD successfully.

• Corrosion Science and Technology
• /
• v.2 no.4
• /
• pp.171-177
• /
• 2003

The electronic properties of the passive film formed on Fe-20Cr ferritic stainless steel in pH 8.5 buffer solution containing 0.05 M EDTA (ethylene diammine tetraacetic acid) were examined by the photocurrent measurements and Mott-Schottky analysis for the film. XPS depth profile for the film demonstrated that Cr content in the outermost layer of the passive film was higher in the solution with EDTA than that in the solution without EDTA, due to selective dissolution of Fe by EDTA. In the solution with EDTA, the passive film showed characteristics of an amorphous or highly disordered n-type semiconductor. The band gap energies of the passive film are estimated to be ~ 3.0 eV, irrespective of film formation potential from 0 to 700 $mV_SCE$ and of presence of EDTA. However, the donor density of the passive film formed in the solution with EDTA is much higher than that formed in the solution without EDTA, due to an increase in oxygen vacancy resulted from the dissolution of Fe-oxide in the outermost layer of the passive film. These results support the proposed model that the passive film formed on Fe-20Cr in pH 8.5 buffer solution mainly consists of Cr-substituted $\gamma$-$Fe_2O_3$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.10
• /
• pp.620-624
• /
• 2015

We have studied structural, optical and electrical properties of In-Ga-doped ZnO (IGZO) thin films. The IGZO thin films were deposited on the corning 1737 glass by RF magnetron sputtering method. The RF power in sputtering process was varied as 30, 50, 70, and 90 W respectively. All of the IGZO thin films transmittance in the visible range (400 nm ~ 800 nm) was above 83%. XRD analysis showed the IGZO thin films amorphous structure of the thin films without any peak. And also IGZO thin film have low resistivity ($1.99{\times}10^{-3}{\Omega}cm$), high carrier concentration ($6.4{\times}10^{20}cm^{-3}$), and mobility ($10.3cm^2V^{-1}s^{-1}$). By the studies we found that IGZO transparent thin film can be used as optoelectronic material and introduced application possibility for future electronic devices.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.254-255
• /
• 2012

Interest in nano-crystalline silicon (nc-Si) thin films has been growing because of their favorable processing conditions for certain electronic devices. In particular, there has been an increase in the use of nc-Si thin films in photovoltaics for large solar cell panels and in thin film transistors for large flat panel displays. One of the most important material properties for these device applications is the macroscopic charge-carrier mobility. Hydrogenated amorphous silicon (a-Si:H) or nc-Si is a basic material in thin film transistors (TFTs). However, a-Si:H based devices have low carrier mobility and bias instability due to their metastable properties. The large number of trap sites and incomplete hydrogen passivation of a-Si:H film produce limited carrier transport. The basic electrical properties, including the carrier mobility and stability, of nc-Si TFTs might be superior to those of a-Si:H thin film. However, typical nc-Si thin films tend to have mobilities similar to a-Si films, although changes in the processing conditions can enhance the mobility. In polycrystalline silicon (poly-Si) thin films, the performance of the devices is strongly influenced by the boundaries between neighboring crystalline grains. These grain boundaries limit the conductance of macroscopic regions comprised of multiple grains. In much of the work on poly-Si thin films, it was shown that the performance of TFTs was largely determined by the number and location of the grain boundaries within the channel. Hence, efforts were made to reduce the total number of grain boundaries by increasing the average grain size. However, even a small number of grain boundaries can significantly reduce the macroscopic charge carrier mobility. The nano-crystalline or polymorphous-Si development for TFT and solar cells have been employed to compensate for disadvantage inherent to a-Si and micro-crystalline silicon (${\mu}$-Si). Recently, a novel process for deposition of nano-crystralline silicon (nc-Si) thin films at room temperature was developed using neutral beam assisted chemical vapor deposition (NBaCVD) with a neutral particle beam (NPB) source, which controls the energy of incident neutral particles in the range of 1~300 eV in order to enhance the atomic activation and crystalline of thin films at room temperature. In previous our experiments, we verified favorable properties of nc-Si thin films for certain electronic devices. During the formation of the nc-Si thin films by the NBaCVD with various process conditions, NPB energy directly controlled by the reflector bias and effectively increased crystal fraction (~80%) by uniformly distributed nc grains with 3~10 nm size. The more resent work on nc-Si thin film transistors (TFT) was done. We identified the performance of nc-Si TFT active channeal layers. The dependence of the performance of nc-Si TFT on the primary process parameters is explored. Raman, FT-IR and transmission electron microscope (TEM) were used to study the microstructures and the crystalline volume fraction of nc-Si films. The electric properties were investigated on Cr/SiO2/nc-Si metal-oxide-semiconductor (MOS) capacitors.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.8
• /
• pp.602-607
• /
• 2013

Concern for the TOS (Transparent Oxide Semiconductor) is increasing with the recent increase in interest for flexible device. Especially MgZnO has attracted a lot of attention. $Mg_xZn_{1-x}O$, which ZnO-based wideband-gap alloys is tuneable the band-gap ranges from 3.36 eV to 7.8 eV. In particular, the flexible substrate, the crystal structure of the amorphous as well as the surface morphology is not good. So research of MgZnO thin films growth on flexible substrate is essential. Therefore, in this study, we studied on the effects of the oxygen partial pressure on the structural and crystalline of $Mg_{0.1}Zn_{0.9}O$ thin films. MgZnO thin films were deposited on PES substrate by using pulsed laser deposition. We used XRD and AFM in order to observe the structural characteristics of MgZnO thin films. UV-visible spectrophotometer was used to get the band gap and transmittance. Crystallization was done at a low oxygen partial pressure. The crystallinity of MgZnO thin films with increasing temperature was improved, Grain size and RMS of the films were increased. MgZnO thin films showed high transmittance over 80% in the visible region.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.11-11
• /
• 2010

Thin-film-transistors (TFTs) that can be deposited at low temperature have recently attracted lots of applications such as sensors, solar cell and displays, because of the great flexible electronics and transparent. Transparent and flexible transistors are being required that high mobility and large-area uniformity at low temperature [1]. But, unfortunately most of TFT structures are used to be $SiO_2$ as gate dielectric layer. The $SiO_2$ has disadvantaged that it is required to high driving voltage to achieve the same operating efficiency compared with other high-k materials and its thickness is thicker than high-k materials [2]. To solve this problem, we find lots of high-k materials as $HfO_2$, $ZrO_2$, $SiN_x$, $TiO_2$, $Al_2O_3$. Among the High-k materials, $Al_2O_3$ is one of the outstanding materials due to its properties are high dielectric constant ( ~9 ), relatively low leakage current, wide bandgap ( 8.7 eV ) and good device stability. For the realization of flexible displays, all processes should be performed at very low temperatures, but low temperature $Al_2O_3$ grown by sputtering showed deteriorated electrical performance. Further decrease in growth temperature induces a high density of charge traps in the gate oxide/channel. This study investigated the effect of growth temperatures of ALD grown $Al_2O_3$ layers on the TFT device performance. The ALD deposition showed high conformal and defect-free dielectric layers at low temperature compared with other deposition equipments [2]. After ITO was wet-chemically etched with HCl : $HNO_3$ = 3:1, $Al_2O_3$ layer was deposited by ALD at various growth temperatures or lift-off process. Amorphous InGaZnO channel layers were deposited by rf magnetron sputtering at a working pressure of 3 mTorr and $O_2$/Ar (1/29 sccm). The electrodes were formed with electron-beam evaporated Ti (30 nm) and Au (70 nm) bilayer. The TFT devices were heat-treated in a furnace at $300^{\circ}C$ and nitrogen atmosphere for 1 hour by rapid thermal treatment. The electrical properties of the oxide TFTs were measured using semiconductor parameter analyzer (4145B), and LCR meter.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.2
• /
• pp.198-203
• /
• 2016

We investigate the effects of magnesium (Mg) suppressor layer on the electrical performances and stabilities of amorphous indium-zinc-tin-oxide (a-ITZO) thin-film transistors (TFTs). Compared to the ITZO TFT without a Mg suppressor layer, the ITZO:Mg TFT exhibits slightly smaller field-effect mobility and much reduced subthreshold slope. The ITZO:Mg TFT shows improved electrical stabilities compared to the ITZO TFT under both positive-bias and negative-bias-illumination stresses. From the X-ray photoelectron spectroscopy O1s spectra with fitted curves for ITZO and ITZO:Mg films, we observe that Mg doping contributes to an enhancement of the oxygen bond without oxygen vacancy and a reduction of the oxygen bonds with oxygen vacancies. This result shows that the Mg can be an effective suppressor in a-ITZO TFTs.

• Korean Journal of Materials Research
• /
• v.23 no.8
• /
• pp.430-434
• /
• 2013

Quantum dots(QDs) with their tunable luminescence properties are uniquely suited for use as lumophores in light emitting device. We investigate the microstructural effect on the electroluminescence(EL). Here we report the use of inorganic semiconductors as robust charge transport layers, and demonstrate devices with light emission. We chose mechanically smooth and compositionally amorphous films to prevent electrical shorts. We grew semiconducting oxide films with low free-carrier concentrations to minimize quenching of the QD EL. The hole transport layer(HTL) and electron transport layer(ETL) were chosen to have carrier concentrations and energy-band offsets similar to the QDs so that electron and hole injection into the QD layer was balanced. For the ETL and the HTL, we selected a 40-nm-thick $ZnSnO_x$ with a resistivity of $10{\Omega}{\cdot}cm$, which show bright and uniform emission at a 10 V applied bias. Light emitting uniformity was improved by reducing the rpm of QD spin coating.At a QD concentration of 15.0 mg/mL, we observed bright and uniform electroluminescence at a 12 V applied bias. The significant decrease in QD luminescence can be attributed to the non-uniform QD layers. This suggests that we should control the interface between QD layers and charge transport layers to improve the electroluminescence.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.348-348
• /
• 2014

차세대 디스플레이 구동 회로 소자를 위한 재료로서, Amorphous Oxide Semiconductor (AOS)가 주목받고 있다. AOS는 기존의 Amorphous Silicon과 비교하여 뛰어난 이동도를 가지고 있으며, 넓은 밴드 갭에 의한 투명한 광학적 특성을 가지고 있다. 이러한 장점을 이용하여, AOS 박막은 thin film transistor (TFT)의 active channel로 이용 되고 있다. 하지만, AOS를 이용한 TFT의 경우, 시간이 경과함에 따라 $O_2$ 및 $H_2O$ 흡착에 의해 전기적 특성이 변하는 현상이 있다. 이러한 현상은 소자의 신뢰성에 있어 중요한 문제가 된다. 이러한 문제를 연구하기 위해 본 논문에서는, AOS 박막을 이용하여 bottom 게이트형 TFT를 제작하였다. 이를 위해 먼저, p-type Si 위에 건식산화방식으로 $SiO_2$(100 nm)를 성장시켜 게이트 산화막으로 이용하였다. 그리고 Zn과 Sn이 1: 2의 조성비를 가진 ZnSnO (ZTO) 용액을 제조한 후, 게이트 산화막 위에 spin coating 하였다. Splin coating된 용액에 남아 있는 솔벤트를 제거하기 위해 10분 동안 $230^{\circ}C$로 열처리를 한 후, 포토리소그래피와 에칭 공정을 이용하여 ZTO active channel을 형성하였다. 그 후, 박막 내에 남아 있는 불순물을 제거하고 ZTO TFT의 전기적인 특성을 향상시키기 위하여, $600^{\circ}C$의 열처리를 30분 동안 진행 하여 junctionless형 TFT 제작을 완료 하였다. 제작된 소자의 시간 경과에 따른 열화를 확인하기 위하여, 대기 중에서 2시간마다 HP-4156B 장비를 이용하여 전기적인 특성을 확인 하였으며, 이러한 열화는 후처리 공정을 통하여 회복시킬 수 있었다. 열화의 회복을 위한 후처리 공정으로, 퍼니스를 이용한 고온에서의 열처리와 microwave를 이용하여 저온 처리를 이용하였다. 결과적으로, TFT는 소자가 제작된 이후, 시간에 경과함에 따라서 on/off ratio가 감소하여 열화되는 경향을 보여 주었다. 이러한 현상은, TFT 소자의 ZTO back-channel에 대기 중에 있는 $O_2$ 및 $H_2O$의 분자의 물리적인 흡착으로 인한 것으로 보인다. 그리고 추가적인 후처리 공정들에 통해서, 다시 on/off ratio가 회복 되는 현상을 확인 하였다. 이러한 추가적인 후처리 공정은, 열화된 소자에 퍼니스에 의한 고온에서의 장시간 열처리, microwave를 이용한 저온에서 장시간 열처리, 그리고 microwave를 이용한 저온에서의 단 시간 처리를 수행 하였으며, 모든 소자에서 성공적으로 열화 되었던 전기적 특성이 회복됨을 확인 할 수 있었다. 이러한 결과는, 저온임에도 불구하고, microwave를 이용함으로 인하여, 물리적으로 흡착된 $O_2$ 및 $H_2O$가 짧은 시간 안에 ZTO TFT의 back-channel로부터 탈착이 가능함과 동시에 소자의 특성을 회복 가능 함 의미한다.