• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.309-309
• /
• 2009

In-Ga-Zn-O (IGZO) has drawn much attention as a compatible material for transparent thin film transistors (TTFT) channel layer due to its high mobility and optical transparency at low processing temperatures. In this work, we investigated the effect of oxygen ambient on structural, electrical and optical properties of amorphous In-Ga-Zn-O (IGZO) thin films by using pulsed laser deposition (PLD). The films were deposited at various oxygen pressures and the structural, electrical and optical properties were investigated. X-ray diffraction (XRD) analysis showed that amorphous IGZO films were grown at all oxygen pressures. The surface morphology and optical properties with various oxygen pressures were studied by field emission scanning electron microscopy (FE-SEM) and UV-VIS spectroscopy, respectively. The grain boundary was observed more apparently and the calculated optical band gap became larger as oxygen pressure increased. To examine the electrical properties, Hall-effect measurements were carried out. The films showed high mobility.

• Current Photovoltaic Research
• /
• v.3 no.2
• /
• pp.54-60
• /
• 2015

ZnSnO thin films were deposited by atomic layer deposition (ALD) process using diethyl zinc ($Zn(C_2H_5)_2$) and tetrakis (dimethylamino) tin ($Sn(C_2H_6N)_4$) as metal precursors and water vapor as a reactant. ALD process has several advantages over other deposition methods such as precise thickness control, good conformality, and good uniformity for large area. The composition of ZnSnO thin films was controlled by varying the ratio of ZnO and $SnO_2$ ALD cycles. The ALD ZnSnO film was an amorphous state. The band gap of ZnSnO thin films increased as the Sn content increased. The CIGS solar cell using ZnSnO buffer layer showed about 18% energy conversion efficiency. With such a high efficiency with the ALD ZnSnO buffer and no light soaking effect, AlD ZnSnO buffer mighty be a good candidate to replace Zn(S,O) buffer in CIGSsolar cells.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.3
• /
• pp.155-158
• /
• 2017

In this paper, ZnO Thin Film Transistors (TFTs) were fabricated by a sol-gel method using a low-temperature process, and their physical and electrical characteristics were analyzed. To lower the process temperature to $200^{\circ}C$, we used a zinc nitrate hydrate ($Zn(NO_3)_2{\cdot}xH_2O$) precursor. Thermo Gravimetric Analyzer (TGA) analysis showed that the zinc nitrate hydrate precursor solution had 1.5% residual organics, much less than the 6.5% of zinc acetate dihydrate at $200^{\circ}C$. In the sol-gel method, organic materials in the precursor disrupt formation of a high-quality film, and high-temperature annealing is needed to remove the organic residuals, which implies that, by using zinc nitrate hydrate, ZnO devices can be fabricated at a much lower temperature. Using an X-Ray Diffractometer (XRD) and an X-ray Photoelectron Spectrometer (XPS), $200^{\circ}C$ annealed ZnO film with zinc nitrate hydrate (ZnO (N)) was found to have an amorphous phase and much more oxygen vacancy ($V_o$) than Zn-O bonds. Despite no crystallinity, the ZnO (N) had conductance comparable to that of ZnO with zinc acetate dihydrate (ZnO (A)) annealed at $500^{\circ}C$ as in TFTs. These results show that sol-gel could be made a potent process for low-cost and flexible device applications by optimizing the precursors.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.134-134
• /
• 2010

Ga-In-Zn-O 물질은 비정질상태에서 높은 전하 운동성을 가지고 있으며 차세대 투명전극 thin film transistor 대안 소재로 각광받고 있다. 그런데 이 물질은 ion sputtering에 따라 전기적인 특성에 큰 변화가 관찰되고 있으며, 이는 표면에서의 화학적 상태가 전기적 특성을 좌우할 것이라는 것을 의미한다. 또한 보다 안정적이고 신뢰적인 소자를 구현하기 위해서는 ion sputtering에 의한 표면에서의 화학적 특성 변화를 이해하는 것이 매우 중요하다는 것을 의미한다. 본 연구에서는 $Ga_2O_3:In_2O_3$:ZnO의 비율이 각각 1:1:1, 2:2:1, 3:2:1 그리고 4:2:1인 시료를 $Ne^+$이온을 이용하여 sputtering하면서 표면에 민감한 분광분석 기법인 x-ray photoelectron spectroscopy와 x-ray absorption spectroscopy를 이용하여 분광정보의 변화들을 연구하였다. 실험에 의하면, Ga 3d의 양에 비해서 In 4d, Zn 3d의 양은 sputtering 시간에 따라서 각 각 양이 줄어들었으며, 전체적으로 보다 산화가가 높은 경향을 보였으며, valence band maximum 근처에 subgap state를 형성하는 것을 관찰하였다. 또한 sputtering을 계속하는 경우 In 3d, In 4d, 및 Fermi energy 근처에 metallic state가 형성되는 것을 관찰하였다. 이러한 subgap state와 metallic state의 관측은 각기 sputtering에 따라서, 아직 명확하지는 않지만, surface state의 형성 및/혹은 oxygen interstitial의 형성 그리고 metallic In의 형성 및/혹은 oxygen defect의 형성이 이루어지는 것을 의미한다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.640-643
• /
• 2007

The effect of plasma damage was investigated on amorphous gallium-indium-zinc oxide (a-GIZO) films and transistors. Ion-bombardment by plasma process affects to turn semiconductor to conductor materials and plasma radiation may degrade to transistor electrical properties. All damages are easily recovered with a $350^{\circ}C$ thermal annealing.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.1
• /
• pp.82-89
• /
• 2017

In this work, InGaZnO thin film transistors with Ni, Al and ITO source and drain electrode materials were fabricated to analyze a hot carrier induced device degradation according to the electrode materials. From the electrical measurement results with electrode materials, Ni device shows the best electrical performances in terms of mobility, subthreshold swing, and $I_{ON}/I_{OFF}$. From the measurement results on the device degradation with source and drain electrode materials, Al device shows the worst device degradation. The threshold voltage shifts with different channel widths and stress drain voltages were measured to analyze a hot carrier induced device degradation mechanism. Hot carrier induced device degradation became more significant with increase of channel widths and stress drain voltages. From the results, we found that a hot carrier induced device degradation in InGaZnO thin film transistors was occurred with a combination of large channel electric field and Joule heating effects.

• Journal of Information Display
• /
• v.9 no.4
• /
• pp.21-29
• /
• 2008

We studied both the wavelength and intensity dependent photo-responses (photofield-effect) in amorphous In-Ga-Zn-O (a-IGZO) thin-film transistors (TFTs). During the a-IGZO TFT illumination with the wavelength range from $460\sim660$ nm (visible range), the off-state drain current $(I_{DS_off})$ only slightly increased while a large increase was observed for the wavelength below 400 nm. The observed results are consistent with the optical gap of $\sim$3.05eV extracted from the absorption measurement. The a-IGZO TFT properties under monochromatic illumination ($\lambda$=420nm) with different intensity was also investigated and $I_{DS_off}$ was found to increase with the light intensity. Throughout the study, the field-effect mobility $(\mu_{eff})$ is almost unchanged. But due to photo-generated charge trapping, a negative threshold voltage $(V_{th})$ shift is observed. The mathematical analysis of the photofield-effect suggests that a highly efficient UV photocurrent conversion process in TFT off-region takes place. Finally, a-IGZO mid-gap density-of-states (DOS) was extracted and is more than an order of magnitude lower than reported value for hydrogenated amorphous silicon (a-Si:H), which can explain a good switching properties observed for a-IGZO TFTs.

• Korean Journal of Materials Research
• /
• v.30 no.4
• /
• pp.211-216
• /
• 2020

Amorphous In-Ga-Zn-O (a-IGZO) thin film transistors, because of their relatively low mobility, have limits in attempts to fulfill high-end specifications for display backplanes. In-Zn-O (IZO) is a promising semiconductor material for high mobility device applications with excellent transparency to visible light region and low temperature process capability. In this paper, the effects of working pressure on the physical and electrical properties of IZO films and thin film transistors are investigated. The working pressure is modulated from 2 mTorr to 5 mTorr, whereas the other process conditions are fixed. As the working pressure increases, the extracted optical band gap of IZO films gradually decreases. Absorption coefficient spectra indicate that subgap states increase at high working pressure. Furthermore, IZO film fabricated at low working pressure shows smoother surface morphology. As a result, IZO thin film transistors with optimum conditions exhibit excellent switching characteristics with high mobility (≥ 30㎠/Vs) and large on/off ratio.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.89-89
• /
• 2011

a-GIZO(비정질 Ga-In-Zn-O)박막은 유연하며 광학적으로 투명하고 높은 전자의 이동도를 갖는 반도체적 특성을 갖기 때문에 차세대 display분야에서 TFT(Thin-Film-Transistor)의 high speed active-matrix layer로써 각광을 받고 있다. 이 물질의 표면은 환경 및 표면처리에 매우 민감하며 [1,2], 이 표면에 metal이 증착되는 경우에도, 선행 연구에 의하면, 다양한 chemical state가 나타남을 알 수 있었다. 이것은 metal의 증착에 따라 metal과 a-GIZO 사이의 contact 저항이 달라짐을 의미한다. 우리는 a-GIZO 박막 위에 Au를 단계적으로 증착시키면서, Au coverage 증가에 따른 core-level과 valence에서의 x-ray photoelectron spectra의 변화를 살펴봄으로써 a-GIZO박막과 Au의 계면에서 일어나는 chemical state의 변화를 알 수 있었다. 특히, Au deposition의 전 처리과정으로써 Ne ion sputtering을 두 단계로 다르게 하여 a-GIZO의 표면환경에 따른 Au 증착의 영향을 살펴보았다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.74-74
• /
• 2011

최근 새로운 형태의 디스플레이에 관한 관심이 집중되고 있다. 이들 중 특히 투명 산화물 반도체는 기존의 실리콘 기반의 반도체에 비해 가시광 영역에서 높은 투과도를 보이며, 또한 기존의 비정질 실리콘 소자에 비해서 10 cm2/Vs이상의 높은 전하 이동도 값을 가진다. 본 연구에서는 투명 산화물 반도체 소재 중 InGaZnO4를 사용하여 펄스 레이저 방법으로 Al2O3 (0001)기판 위에 비정질 상태인 a-InGaZnO4 박막을 성장 시켰다. 박막의 증착 온도를 변화(RT, $50^{\circ}C$, $150^{\circ}C$, $250^{\circ}C$, $450^{\circ}C$, $550^{\circ}C$)시켜 성장된 박막의 구조적, 화학적, 전기적 그리고 광학적 특성을 조사하였다. 증착 온도가 $450{\sim}550^{\circ}C$ 사이에서 박막의 상태가 비정질(amorphous)에서 polycrystalline으로 성장되는 것을 X-Ray Diffraction과 Field Emission-Scanning Electron Microscope를 이용하여 확인하였고 이는 InGaZnO4 박막의 결정화 온도가 $450^{\circ}C$ 이상임을 알 수 있었다. X-ray Photoelectron Spectroscopy를 통해서 target 물질과 성장된 박막의 조성 및 화학적 상태를 고찰한 결과, 박막의 결정성 변화가 화학적 상태 변화와는 무관하다는 사실을 알 수 있었다. 온도 의존 비저항 측정을 통해 박막이 반도체 성향을 가지는 것을 확인 하였다. 또한 Hall 측정 결과 증착 온도가 올라 갈수록 전하 밀도는 증가 하지만, 전하 이동도는 다결정 박막($550^{\circ}C$)에서 급격히 감소하고, 이로 인해 비저항 값이 크게 증가함을 알 수 있었다. 이는 다결정 박막 내 존재하는 grain boundary들이 이동도 값에 영향을 준다는 것으로 추측할 수 있다. Ultra violet-Visible-Near Infrared 측정을 통해 가시광 영역에서 80%이상의 투과율을 나타내며 증착 온도가 증가함에 따라 에너지 밴드갭(Eg)이 커지는 것을 확인 할 수 있는데 이는 Hall 측정 결과에서 확인한 전하 밀도의 증가로 인해 에너지 밴드갭이 커지는 Burstein-Moss 효과로 설명할 수 있다.