• Journal of Electrochemical Science and Technology
• /
• v.10 no.1
• /
• pp.14-21
• /
• 2019

Supported liquid membrane process usually is used for recovering or enrichment of valuable metals in the industrial wastewater. But, even if the metals in the wastewater was separated with high chemical selectivity, it cannot be enough concentrated since separation performance of supported liquid membrane (SLM) process is limited by concentration gradient between feed solution and stripping solution. If metal concentration in the stripping solution to be enough low, transport of metal through membrane can be accomplishment constantly. Therefore, Electrodialysis (ED) has been placed after SLM process and the stripping solution of SLM was used as the feed solution for the ED process. Transport of ions in the solutions is successfully performed by ED process. Thus, the metal concentration in the stripping solution does not rise as to stop ion transport. Besides, valuable metals easily are concentrated by ED process for re-use. In this study, effects of operation parameters like initial Cd(II) concentration, HCl concentration in the feed solution of SLM and applied voltage are investigated on separation efficiency, flux and permeability of the both processes. As the feed solution concentration increased, all performance values has increased. When initial concentration of 100 mg/L is used, separation performances (SP) are 55% and 70%, for SLM and consecutive process, respectively. The best HCl concentration in the feed solution of SLM has determined as 2 M, in this conditions SP are 64% and 72%, for SLM and consecutive process, respectively. With increased of applied voltage on ED process, SP of the consecutive process has been raised from 72% to 83%. According to the obtained experimental data, consecutive process has better separation performance than SLM. When the separation performances of both processes were compared for the same operating conditions, it was determined higher the separation efficiency, permeability and flux values of the consecutive process, 8%, 9% and %10.6, respectively. Consequently, the use of the consecutive process increases the performance efficiency of both processes. The consecutive process studied has quite a good chemical separation efficiency, and enrichment capability. Moreover, this process requires few water and energy.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.500-503
• /
• 1999

In this paper, we analyze weight distributions of neural networks. If we construct a vector containing all weights of a neural network, then training process can be viewed as finding a solution point in the weight space. In order to obtain insight into the training process of neural networks, we investigate the distribution of the solution points in the weight space Experiments provide some interesting results, showing that solution points tend to form clusters in the weight space and the information may be used to speed up the training process.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.16 no.2
• /
• pp.21-27
• /
• 2008

An inverse method is introduced to construct the problem for the error analysis of the numerical solution of initial value problem. These problems constructed through this method have a known exact solution, even though analytical solutions are generally not obtainable. The process leading to the exact solution makes use of an initially available approximate numerical solution. A smooth interpolation of the approximate solution is forced to exactly satisfy the differential equation by analytically deriving a small forcing function to absorb all of the errors in the interpolated approximate solution. Using this special case exact solution, it is possible to investigate the relationship between global errors of a candidate numerical solution process and the associated tuning parameters for a given problem. Under the assumption that the original differential equation is well-posed with respect to the small perturbations, we thereby obtain valuable information about the optimal choice of the tuning parameters and the achievable accuracy of the numerical solution.

• Advances in Computational Design
• /
• v.5 no.3
• /
• pp.305-321
• /
• 2020

In this paper is presented the solution method for three-dimensional problem of transversely isotropic body's elastoplastic deformation by the finite element method (FEM). The process of problem solution consists of: determining the effective parameters of a transversely isotropic medium; construction of the finite element mesh of the body configuration, including the determination of the local minimum value of the tape width of non-zero coefficients of equation systems by using of front method; constructing of the stiffness matrix coefficients and load vector node components of the equation for an individual finite element's state according to the theory of small elastoplastic deformations for a transversely isotropic medium; the formation of a resolving symmetric-tape system of equations by summing of all state equations coefficients summing of all finite elements; solution of the system of symmetric-tape equations systems by means of the square root method; calculation of the body's elastoplastic stress-strain state by performing the iterative process of the initial stress method. For each problem solution stage, effective computational algorithms have been developed that reduce computational operations number by modifying existing solution methods and taking into account the matrix coefficients structure. As an example it is given, the problem solution of fibrous composite straining in the form of a rectangle with a system of circular holes.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.641-641
• /
• 2013

We report the transparentsilver nanowire electrode fabricated by a direct printing process, liquid-bridge-mediated nanotransfer molding. We fabricated silver nanowire arrays by liquidbridge- mediated nanotransfer molding using the silver nanoparticle ink and PEDOT:PSS polymer. Weinvestigated the formation of silver nanowire arrays by SEM and transmittance of the transparent silver nanowire electrode. We also measured the conductivity to confirm the potential of our approach.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.11
• /
• pp.130-139
• /
• 2004

The Casing Oscillator is a bore file Equipment for the all-casing process. All-casing process is a method of foundation work in construction yard to oscillate steel Casing in the ground. The existing Casing Oscillator has some problem like not boring horizontally with disturbance and not driving Casing othor angle except horizon. To solve problem, the new structure Casing Oscillator is presented and studied. The performance of Casing Oscillator is improved by kinematics analysis. The Casing Oscillator is similar to the parallel manipulator in structure. So we obtain Inverse kinematics solution of Casing Oscillator easily. But it is difficult to solve forward kinematics of Casing Oscillator. T his paper presents a novel pose description corresponding to the structure characteristics of parallel manipulators. Through analysis on geometry theory, we obtain a new method of the closed-form solution to the forward kinematics using Kinematic Inversion. The closed-form solution contains two different meanings -analytical and real-time. So we reach the goal of practical application and control. Closed-form forward kinematics solution is verified by an inverse kinematics analysis. It shows that the method has a practical value for real -time control and inverse kinematics servo control.

• International Journal of Aeronautical and Space Sciences
• /
• v.3 no.2
• /
• pp.46-58
• /
• 2002

An inverse method is introduced to construct benchmark problems for the numerical solution of initial value problems. Benchmark problems constructed through this method have a known exact solution, even though analytical solutions are generally not obtainable. The solution is constructed such that it lies near a given approximate numerical solution, and therefore the special case solution can be generated in a versatile and physically meaningful fashion and can serve as a benchmark problem to validate approximate solution methods. A smooth interpolation of the approximate solution is forced to exactly satisfy the differential equation by analytically deriving a small forcing function to absorb all of the errors in the interpolated approximate solution. A multi-variable orthogonal function expansion method and computer symbol manipulation are successfully used for this process. Using this special case exact solution, it is possible to directly investigate the relationship between global errors of a candidate numerical solution process and the associated tuning parameters for a given code and a given problem. Under the assumption that the original differential equation is well-posed with respect to the small perturbations, we thereby obtain valuable information about the optimal choice of the tuning parameters and the achievable accuracy of the numerical solution. Illustrative examples show the utility of this method not only for the ordinary differential equations (ODEs) but for the partial differential equations (PDEs).

• Journal of Surface Science and Engineering
• /
• v.25 no.3
• /
• pp.117-125
• /
• 1992

In the electrolysis process of zinc plating impurity ions must be removed from zinc chloride plating solution because it's harmful to the current efficiency and the purity of zinc plating. In this study using zinc ball as a prcipitant instead of zinc dust, the fundamental data for continuous cementation process was studied. Based upon two series of experiments that consist of batch experiment with cylindrical zinc specimen and continuous experiment with zinc balls, following results have been obtained. In the continuous experiment all impurity ions have been removed within 1 hour regardless of various experimental conditions.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.12
• /
• pp.1710-1719
• /
• 1997

An approximate analytical solution for the initial transient process of close-contact melting occurring between a phase change material kept at its melting temperature and an isothermally heated flat surface is derived. The model is so developed that it can cover both rectangular and circular cross-sectional solid blocks. Normalization of simplified model equations in reference to the steady solution enables the solution to be expressed in a generalized form depending on the liquid-to-solid density ratio only. A selected result shows an excellent agreement with the previously reported numerical data, which justifies the present approach. The solution appears to be capable of describing all the fundamental characteristics of the transient process. In particular, dependence of the solid descending velocity oft the density ratio at the early stage of melting is successfully resolved. The effects of other parameters except the density ratio on the transient behaviors are efficiently represented via the steady solution implied in the normalized result. A simple approximate method for estimating the effect of convection on heat transfer across the liquid film is also proposed.

• Journal of Korean Institute of Industrial Engineers
• /
• v.23 no.2
• /
• pp.307-321
• /
• 1997

In this paper, we consider the expert's ambiguity and the decision maker's fuzzy goals which are incorporated into multiobjective nonlinear programming problems in order to find a compensatory solution. The proposed method can be applied to all cases of multiobjective problems with fuzzy parameters since the interactive process with a decision maker is simple, various uncertainties involved in decision making are eliminated and all the objectives are well balanced. An illustrative numerical example for nonlinear programming problems with fuzzy parameters is demonstrated along with the corresponding computer output.