Journal of the Korean institute of surface engineering
/
v.42
no.6
/
pp.287-293
/
2009
The passivation films with epoxy layer on LiF, $SiN_x$ and LiF/$SiN_x$ inorganic layer were fabricated on OLED to protect device from the direct damage of $O_2$ and $H_2O$ and to apply for a buffer layer between OLED device and passivation multi-layer with organic/inorganic hybrid structure as to diminish the thermal stress and expansion. Red OLED doped with 1 vol.% Rubrene in $Alq_3$ was used as a basic device. The device structure was multi-layer of ITO(150 nm) / ELM200_HIL(50 nm) / ELM002_HTL(30 nm) / $Alq_3$: 1 vol.% Rubrene(30 nm) / $Alq_3$(30 nm) / LiF(0.7 nm) / Al(100 nm). LiF/epoxy applied as a protective layer didn't contribute to the improvement of life time. While in case of $SiN_x$/epoxy, damage was done in the passivation process because of difference in heat expansion between films which could occur during the formation of epoxy film. Using LiF/$SiN_x$/epoxy improved lifetime significantly without suffering damage in the process of forming films, therefore, the best structure of passivation film with inorganic/epoxy layers was LiF/$SiN_x$/E1.
Seung Woong Lee;Hoon Young Cho;Eun Kyu Kim;Suk-Ki Min;Jung Ho Park
Journal of the Korean Crystal Growth and Crystal Technology
/
v.4
no.1
/
pp.11-20
/
1994
GaAs and AlGaAs epi-layers were grown on semi-insulating (100) GaAs substrate by molecular beam epitaxy (MBE) and their electrical and optical properties have been investigated by several measurements. In undoped GaAs, the p-type GaAs layers with the good surface morphology were obtained under the growth conditions of the substrate temperatures ranging from 570 to $585^{\circ}C$ and the $As_4$/Ga ratios from 17 to 22. In the samples with the growth rates of the ranges of $0.9~1.1 {\mu}m/h$, the impurity concentrations were in the ranges of $1.5{\times}10^{14}~5.6{\times}10^{14}cm^{-3}$ with the Hall mobilities of $590~410cm^2/V-s$. In the Si-doped GaAs, the n-type GaAs layers with low electro trap, only two hole deep levels were observed with uniform doping profiles (<1%). AlGaAs layers with good surface morphology and crystallinity were grown under an optimum condition of the substrate temperature, $600^{\circ}C $. 8 deep level defects were observed between 0.17~0.85eV in undoped AlGaAs layers.
High-efficiency phosphorescent organic light emitting diodes using TCTA-TAZ as a double host and $Ir(ppy)_3$ as a dopant were fabricated and their electro-luminescence properties were evaluated. The fabricated devices have the multi-layered organic structure of 2-TNATA/NPB/(TCTA-TAZ) : $Ir(ppy)_3$/BCP/SFC137 between an anode of ITO and a cathode of LiF/AL. In the device structure, 2-TNATA[4,4',4"-tris(2-naphthylphenyl-phenylamino)-triphenylamine] and NPB[N,N'-bis(1-naphthyl)-N,N'-diphenyl-1,1'-biphenyl-4,4'-diamine] were used as a hole injection layer and a hole transport layer, respectively. BCP [2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline] was introduced as a hole blocking layer and an electron transport layer, respectively. TCTA [4,4',4"-tris(N-carbazolyl)-triphenylamine] and TAZ [3-phenyl-4-(1-naphthyl)-5-phenyl-1,2,4-triazole] were sequentially deposited, forming a double host doped with $Ir(ppy)_3$ in the [TCTA-TAZ] : $Ir(ppy)_3$ region. Among devices with different thickness combinations of TCTA ($50\;{\AA}-200\;{\AA}$) and TAZ ($100\;{\AA}-250\;{\AA}$) within the confines of the total host thickness of $300\;{\AA}$ and an $Ir(ppy)_3$-doping concentration of 7%, the best electroluminescence characteristics were obtained in a device with $100\;{\AA}$-think TCTA and $200\;{\AA}$-thick TAZ. The $Ir(ppy)_3$ concentration in the doping range of 4%-10% in devices with an emissive layer of [TCTA ($100\;{\AA}$)-TAZ ($200\;{\AA}$)] : $Ir(ppy)_3$ gave rise to little difference in the luminance and current efficiency.
Proceedings of the Materials Research Society of Korea Conference
/
2010.05a
/
pp.59-59
/
2010
ZnO는 II-VI 족 화합물 반도체로써 상온에서 큰 엑시톤 결합에너지 (~60 meV) 를 가지며 밴드갭이 3.37 eV인 직접 천이형 반도체로 잘 알려진 물질이다. 이러한 ZnO의 물리적 특성은 광학소자로 상용화된 GaN와 유사하기 때문에 LED나 LD등의 광 소자 재료로 주목 받고 있다. 또한 ZnO는 3족 원소 (In, Ga, Al)를 도핑 함으로써 전기적 특성 제어가 가능한 장점을 가지고 있다. 본 연구는 펄스레이저 증착법 (Pulsed Laser Deposition)을 이용하여 Si (111) 기판 위에 ZnO:In 박막을 성장 시켰으며, 도핑된 indium 양에 따른 ZnO 박막의 배향성 변화를 관찰 하였다. X-선 회절 분석법 (X-ray diffraction), 탐침형 원자현미경 (Atomic Force Microscope) 그리고 투과전자 현미경 (Transmission Electron Microscope)을 측정하였다. XRD 측정 결과 un-doped ZnO 박막은 (002) 방향으로 c-축 우선성장 하였다. 그러나 ZnO 박막내의 Indium 양이 증가 할수록 (002) 방향에서 (101), (102), (103) 등의 (101) 방향으로 성장이 변화 하였으며 5 at.% 이상에서는 (100) 방향의 성장이 관찰 되었다. TEM 측정 결과 un-doped ZnO 박막은 columnar 구조로 성장 되었으나, Indium 양이 증가할수록 column의 size가 감소하며, 5 at.% 이상에서 columnar 구조 성장이 거의 관찰되지 않는다. AFM 결과에서는 Indium 양이 증가 할수록 박막의 표면거칠기와 결정립 크기가 감소하였다.
Blue light-emitting phosphors having the excitation spectrum range of the medium-long ultraviolet ($280nm{\sim}400nm$) have been prepared by solid state reaction method. As a starting material the natural alkaline feldspar powder produced from the domestic mine field in Buyeo, Chungnam-do. The photoluminescence characteristics and crystal structures have been analyzed for the phosphor samples. The powder mixture of the natural alkaline feldspar and the rare-earth oxide was calcined at $800{\sim}1000^{\circ}C\;for\;3{\sim}4h$ in air. The calcined samples we fully ground at room temperature and then heat-treated in the mild reducing gas atmosphere of $5%H_2-95%N_2$ mixture at $1100{\sim}1150^{\circ}C\;for\;3{\sim}4h$. The natural alkaline feldspar material consists of the monoclinic orthoclase ($KAlSi_3O_8$) and the triclinic albite ($NaAlSi_3O_8$) phases. At the $0.5wt%Eu_2O_3$ addition the PL spectrum showed the maximum intensity and with further increase of $Eu_2O_3$ the PL intensity decreased. The albite phase disappeared in the $Eu_2O_3$ doped phosphors. The effect of the co-doped activator on the PL characteristics have been also discussed.
Proceedings of the Korean Vacuum Society Conference
/
2010.02a
/
pp.449-449
/
2010
유기발광소자(organic light-emitting diodes, OLEDs)는 저공정비용, 경량화, 가용성 및 대면적화 등의 장점으로 조명 분야와 디스플레이 분야로의 응용 가능성으로 인해 크게 주목을 받아 왔다. 이러한 OLED 소자의 고효율, 고휘도 및 저소비전력 등을 구현하기 위해서는 전극으로부터 전하 주입 층으로 효율적인 전하 주입이 요구된다. 즉, 각 전극의 폐르미 준위로부터 전하 전도준위대로의 전하주입 장벽이 없어야 한다. 본 연구에서는 홀 주입장벽이 없는 정공주입 층으로 $MoO_x$(molybdenum oxide)가 도핑된 NPB(N, N'-diphenyl-N, N'-bis(1-naphthyl)-1,1'-biphenyl-4,4'-diamine) 층을 사용하여 hole-only 소자를 제작하고 전류-전압 특성을 통해 양극으로부터 홀주입 층으로의 hole-ohmic 특성을 고찰했다. 또한, 전자 주입장벽이 없는 전자주입 층으로 $C_{60}$(fullerene)/LiF(lithum fluoride)의 이종 층을 사용하여 electron-only 소자를 제작하고 음극으로부터 전자주입 층으로의 전자 ohmic 특성을 조사했다. 또한, 전극으로부터 전하주입 층으로 ohmic 특성을 더 자세히 이해하기 위하여 전하주입 층의 자외선 광방출 스펙트럼(ultraviolet photoemission spectra)을 조사했다. 한편, glass/ITO/$MoO_x$-doped NPB (x%: x=0,25, 50 및 75; 5nm)/NPB (63nm)/$Alq_3$ (37nm)/$C_{60}$ (5nm)/LiF (1nm)/Al (100nm)로 구성된 all-ohmic OLED 소자의 발광특성은 $MoO_x$의 도핑 농도가 25%이상일 때 최적의 특성을 보여줬다. 이러한 현상은 정공주입 층에서 p형 도핑 농도의 증가에 따른 정공 농도의 증가에 기인한다. 또한 $MoO_x$의 도핑 농도의 증가에 따라 정공주입 층의 new gap state와 전극의 페르미 준위의 pinning에 기인한다. 25%의 $MoO_x$을 가진 OLED소자는 7.2V의 낮은 전압에서 $58300 cd/m^2$의 높은 휘도를 보여줬다.
Lee, S. J.;H. F. Luan;A. Mao;T. S. Jeon;Lee, C. h.;Y. Senzaki;D. Roberts;D. L. Kwong
JSTS:Journal of Semiconductor Technology and Science
/
v.1
no.4
/
pp.202-208
/
2001
In Recent results suggested that doping $Ta_2O_5$ with a small amount of $TiO_2$ using standard ceramic processing techniques can increase the dielectric constant of $Ta_2O_5$ significantly. In this paper, this concept is studied using RTCVD (Rapid Thermal Chemical Vapor Deposition). Ti-doped $Ta_2O_5$ films are deposited using $TaC_{12}H_{30}O_5N$, $C_8H_{24}N_4Ti$, and $O_2$ on both Si and $NH_3$-nitrided Si substrates. An $NH_3$-based interface layer at the Si surface is used to prevent interfacial oxidation during the CVD process and post deposition annealing is performed in $H_2/O_2$ ambient to improve film quality and reduce leakage current. A sputtered TiN layer is used as a diffusion barrier between the Al gate electrode and the $TaTi_xO_y$ dielectric. XPS analyses confirm the formation of a ($Ta_2O_5)_{1-x}(TiO_2)_x$ composite oxide. A high quality $TaTi_xO_y$ gate stack with EOT (Equivalent Oxide Thickness) of $7{\AA}$ and leakage current $Jg=O.5A/textrm{cm}^2$ @ Vg=-1.0V has been achieved. We have also succeeded in forming a $TaTi_x/O_y$ composite oxide by rapid thermal oxidation of the as-deposited CVD TaTi films. The electrical properties and Jg-EOT characteristics of these composite oxides are remarkably similar to that of RTCVD $Ta_2O_5, suggesting that the dielectric constant of $Ta_2O_5$ is not affected by the addition of $TiO_2$.
Most TCOs such as ITO, AZO(Al-doped ZnO), FTO(F-doped $SnO_2$) etc., which have been widely used in LCD, touch panel, solar cell, and organic LEDs etc. as transparent electrode material reveal n-type conductivity. But in order to realize transparent circuit, transparent p-n junction, and introduction of transparent p-type materials are prerequisite. Additional prerequisite condition is optical transparency in visible spectral region. Oxide based materials usually have a wide optical bandgap more than ~3.0 eV. In this study, single-phase transparent semiconductor of $SrCu_2O_2$, which shows p-type conductivity, have been synthesized by 2-step solid state reaction at $950^{\circ}C$ under $N_2$ atmosphere, and single-phase $SrCu_2O_2$ thin films of p-type TCOs have been deposited by RF magnetron sputtering on alkali-free glass substrate from single-phase target at $500^{\circ}C$, 1% $H_2$/(Ar + $H_2$) atmosphere. 3% $H_2$/(Ar + $H_2$) resulted in formation of second phases. Hall measurements confirmed the p-type nature of the fabricated $SrCu_2O_2$ thin films. The electrical conductivity, mobility of carrier and carrier density $5.27{\times}10^{-2}S/cm$, $2.2cm^2$/Vs, $1.53{\times}10^{17}/cm^3$ a room temperature, respectively. Transmittance and optical band-gap of the $SrCu_2O_2$ thin films revealed 62% at 550 nm and 3.28 eV. The electrical and optical properties of the obtained $SrCu_2O_2$ thin films deposited by RF magnetron sputtering were compared with those deposited by PLD and e-beam.
Proceedings of the Korean Vacuum Society Conference
/
2012.08a
/
pp.194-195
/
2012
박막 실리콘 태양전지에 입사한 빛 중 흡수층인 진성 비정질 실리콘층(i-a-Si)에 흡수된 빛은 출력으로 변환되나, 기타의 층에서 흡수된 빛은 손실 성분이 된다. 이 중 흡수 손실이 큰 층은 도핑 층(p-a-SiC 및 n-a-Si)들인데, 이 들의 흡수 손실을 측정된 광학함수를 이용해 계산해 보면 Fig. 1과 같이 나타난다. p-a-SiC은 광 입사부에 위치하여 단파장 영역의 흡수 손실을 일으키고, n-a-Si 은 태양전지의 후면에 위치하여 장파장 영역의 흡수손실을 일으킨다. 이러한 도핑층에서의 흡수 손실을 제거 또는 개선하기 위해 도핑층의 재료를 기존 재료보다 광학적 밴드갭이 큰 재료로 대체하여 개선하는 방안에 대해 논하고자 한다. 금속 산화물의 밴드갭은 실리콘 화합물에 비하여 대체로 큰 값을 가지기 때문에 이를 기존의 실리콘 화합물 대신으로 사용한다면 광학적 흡수 손실을 효과적으로 줄일 수 있다. 단, 이때 태양전지의 광 전압을 결정하는 인자가 p층과 n층 사이의 일함수 차이에 해당하므로, p층의 대체층으로 사용 가능한 금속 산화물은 일함수가 큰(>5 eV) 재료 중에서 선택하는 것이 적합하며, n층의 대체층으로 사용 가능한 금속 산화물은 일함수가 작은(< 4.2 eV) 재료 중에서 선택하는 것이 적합하다. Table 1에서 p층과 n층 대체용 금속산화물의 후보들을 정리하였다. 먼저 도핑층에서의 광 흡수가 광손실이 될 수 밖에 없는 물리적 근거에 대해서 논하고, 그 실험적인 증명을 제시한다. 이러한 개념을 바탕으로 도핑층의 내부 전기장의 방향을 제어하여 전자-정공쌍을 분리 수집하는 방법을 실험적으로 구현하였다. 이어서 금속 산화물을 부분적으로 대체하여 흡수 손실을 개선하는 방안을 제시한다. WOx, NiOx, N doped ZnO 등을 적용하여 그 효과를 비교 검토하였다. 끝으로 금속산화믈 대체 또는 쇼트키 접합을 적용하여 도핑층의 광 흡수를 줄이고 효율을 향상하는 방안을 제시한다. 그 사례로서 WOx, MoOx, LiF/Al의 적용결과를 살펴보고 추가 개선방안에 대해 토의할 것이다. 결론적으로 광학적 밴드갭이 큰 재료를 도핑층 대신 사용하여 흡수 손실을 줄이는 것이 가능하다는 것을 알 수 있고, 이 때 일함수 조건이 만족이 되면 광 전압의 손실도 최소화할 수 있다는 점을 확인할 수 있었다. 현재까지 연구의 한계와 문제점을 정리하고, 추가 연구에 의한 개선 가능성 및 실용화 개발과의 연관관계 등을 제시할 것이다.
In this paper, HBT's with lower phase noise and passive elements, such as resistors, capacitors and inductors, for resonance and impedance matching networks are designed, fabricated, tested, and carefully analysed, respectively, and then, they are integrated for the design and fabrication of functional X-band oscillators with lower phase noise. Epi-wafers for HBT's with the structure of graded $Al_{x}$G $a_{1-x}$ As emitter and C-doped base layer of 700.angs. thick were used to specially emphasize the improvement of $f_{T}$ and $f_{max}$, and the lowering of phase noise, in design aspects. At the test frequencies of 12GHz, capacitances of MIM capacitors, spiral inductor, and resistances are 0.5~10pF, 0.4~11.06nH, and 20~1,380.ohm., respectively. The emitter size of HBY's for the X-band MMIC oscillators is 3*10u $m^{2}$, and find chip size is 0.9*0.9m $m^{2}$..EX>.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.