• Korean Journal of Materials Research
• /
• v.5 no.2
• /
• pp.169-177
• /
• 1995

The diffusion barrier property of 100-nm-thick titanium nitride (TiN) film between Cu and Si was investigated using sheet resistance measurements, etch-pit observation, x-ray diffractometry, Auger electron spectroscopy, and transmission electron microscopy. The TiN barrier fails due to the formation of crystalline defects (dislocations) and precipitates (presumably Cu-silicides) in the Si substrate which result from the predominant in-diffusion of Cu through the TiN layer. In contrast with the case of Al, it is identified that the TiN barrier fails only the in-diffusion of Cu because there is no indication of Si pits in the Si substrate. In addition, it appears that the stuffing of TiN does not improve the diffusion barrier property in the Cu/TiN/Si structure. This indicates that in the case of Al, the chemical effect that impedes the diffusion of Al by the reaction of Al with $TiO_{2}$ which is present in the grain boundaries of TIN is very improtant. On the while, in the case of Cu, there is no chemical effect because Cu oxides, such as $Cu_{2}O$ or CuO, is thermodynamically unstable in comparison with $TiO_{2}$. For this reason, it is considered that the effect of stuffing of TiN on the diffusion barrier property is not significant in the Cu/ TiN/Si structure.

• Transactions of Materials Processing
• /
• v.28 no.1
• /
• pp.43-48
• /
• 2019

Aluminum nitride (AlN) is used by the semiconductor industry, and is a compound that is required when manufacturing high thermal conductivity. The AlN films with c-axis orientation and thermal conductivity characteristic were deposited by using the Pulsed Laser Deposition (PLD). The AlN thin films were characterized by changing the deposition conditions. In particular, we have researched the AlN thin film deposited under optimal conditions for growth atmosphere. The epitaxial AlN films were grown on sapphire ($c-Al_2O_3$) single crystals by PLD with AlN target. The AlN films were deposited at a fixed temperature of $650^{\circ}C$, while conditions of nitrogen ($N_2$) pressure were varied between 0.1 mTorr and 10 mTorr. The quality of the AlN films was found to depend strongly on the $N_2$ partial pressure that was exerted during deposition. The X-ray diffraction studies revealed that the integrated intensity of the AlN (002) peak increases as a function the corresponding Full width at half maximum (FWHM) values decreases with lowering of the nitrogen partial pressure. We found that highly c-axis orientated AlN films can be deposited at a substrate temperature of $650^{\circ}C$ and a base pressure of $2{\times}10^{-7}Torr$ in the $N_2$ partial pressure of 0.1 mTorr. Also, it is noted that as the $N_2$ partial pressure decreased, the thermal conductivity increased.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.28 no.4
• /
• pp.170-174
• /
• 2018

AlN crystal is been developing in global site for many years and 1 inch diameter wafer was already developed but it is demanding the efforts for the better quality. On the other hand, also the 2-inch size is developing recently to reduce the unit cost for manufacturing and to use to fabrication of the UV LED chips. In this study, we tried to evaluate the possibility of bulk AlN crystals on his thin films by PVT method. The AlN thin film was grown on SiC single crystal 2" wafer by HVPE method. We successfully grew AlN bulk crystal of a thickness of 7 mm using its thin film of a thickness of $10{\mu}m$ as a seed crystal. The resultants of AlN crystals were identified by metallurgical microscope, optical stereographic microscope and DCXRD measurement.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.235-235
• /
• 2009

This paper describes the influence of a polycrystalline (poly) 3C-SiC buffer layer on the surface acoustic wave (SAW) properties of poly aluminum nitride (AlN) thin films by comparing the center frequency, insertion loss, the electromechanical coupling coefficient ($k^2$), andthetemperaturecoefficientoffrequency(TCF) of an IDT/AlN/3C-SiC structure with those of an IDT/AlN/Si structure, The poly-AlN thin films with an (0002)-preferred orientation were deposited on a silicon (Si) substrate using a pulsed reactive magnetron sputtering system. Results show that the insertion loss (21.92 dB) and TCF (-18 ppm/$^{\circ}C$) of the IDT/AlN/3C-SiC structure were improved by a closely matched coefficient of thermal expansion (CTE) and small lattice mismatch (1 %) between the AlN and 3C-SiC. However, a drawback is that the $k^2(0.79%)$ and SAW velocity(5020m/s) of the AlN/3C-SiC SAW device were reduced by appearing in some non-(0002)AlN planes such as the (10 $\bar{1}$ 2) and (10 $\bar{1}$ 3) AlN planes in the AlN/SiC film. Although disadvantages were shown to exist, the use of the AlN/3C-SiC structure for SAW applications at high temperatures is possible. The characteristics of the AlN thin films were also evaluated using FT-IR spectra, XRD, and AFM images.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.5
• /
• pp.525-531
• /
• 1996

(Ti1-xAlx)N films were deposited on high speed steel and silicon substrates by reactive sputtering in mixed $Ar-N_2$ discharges. Crystalline phases and microhardness of ($Ti_1_xAl_x$)N films were investigated with variation of the film composition and substrate RF bias voltage. With Al content x of about 0.6, crystalline phase of ( $Ti_1_xAl_x$N films was changed from single-phase NaCl structure to two phase mixture of NaCl and wurtzite structures: Microhardness of ($Ti_1_xAl_x$)N films was largely improved by applying RF bias voltage above 50 V during deposition. Hardness of ($Ti_1_xAl_x$)N films reached a maximum value for Al content x of about 0.4, and 1900 kg/$mm^2$ was obtained for 1$\mu m$-thick ($Ti_{0.6}Al_{0.4}$)N films.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.5
• /
• pp.458-462
• /
• 2008

In this paper, we investigated the (002) preferred orientation and morphology characteristics of AlN thin film by using reactive rf sputtering. Additionally, AlN thin films grown in the range from 150 to 300 W were studied under room temperature without substrate heating and post annealing. Sputtered AlN thin films were well grown on Si substrates and the (002) main peak in XRD patterns showed the highest intensity at 300 W with $0.25^{\circ}$ degree of full width at half-maximum (FWHM). As increased RF power, the surface roughness was increased from 1.0 to 3.4 nm. In Fourier transformation infrared spectroscopy (FTIR), $A_1$ (TO) and $E_1$ (TO) mode closed to AlN thin film confirmed the changes with increasing the intensity rate. From these results, we could confirm a chance of the growth of AlN thin film by only low temperature.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.2
• /
• pp.97-104
• /
• 2001

($Ti_{ 1-x}$$Al_{ x}$)N has been deposited on high speed steel (HSS) substrate using PECVD from the gas mixture of $TiC1_4$, $AlC1_4$, $NH_3$, $H_2$, and Ar. The correlation between the microstructure and the mechanical properties was investigated. ($Ti_{1-x}$$Al_{ x}$)N showed single phase NaCl-structure up to X=0.87, while a mixed phase of NaCl Type (Ti, Al) N and wurtzite structure AlN was observed for 0.87$Ti_{1-x}$ $Al_{x}$ )N became by degrees as increasing X, which made the hardness of the coating higher by Al addition. When the coating was composed of a mixed phase, however, the hardness decreased abruptly due to the effect of soft AlN phase. The wear volume of the coatings could be obtained as the concentration of the coating was varied, and the relation between the wear volume and hardness or the adhesion strength was discussed.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.7
• /
• pp.17-25
• /
• 1999

Tungsten nitride($WN_x$) films were deposited by PECVD method on silicon nitride($WSi_3N_4$) substrate. The characteristics of $WN_x$ film were investigated with changing various processing parameters ; substrate temperature, gas flow rate, rf power, and different nitrogen sources. The nitrogen composition in $WN_x$ film varied from 0 to 45% according to the $NH_3$ and $N_2$ flow rate. The highest deposition rate of 160 nm/min was obtained for the $NH_3$ gas and relatively low deposition rate of $WN_x$ films were formed by $N_2$ gas. $WN_x$ films deposited on $WSi_3N_4$ substrate had higher deposition rate than that of TiN and Si substrates. The purity of $WN_x$ film were analyzed by AES and higher purity $WN_x$ films were deposited using $NH_3$ gas. The XRD analysis indicates a phase transition from polycrystalline tungsten(W) to amorphous tungsten nitride($WN_x$), showing improved etching profile of $WN_x$ films Thick $WN_x$ films were deposited on various substrates such as Tin, NiCr and Al and maximum thickness of $1.6 {\mu}m$ was obtained on the Al adhesion layer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.509-512
• /
• 2001

Aluminum nitride(AlN) thin films were deposited on silicon substrates using RF magnetron sputtering at various deposition conditions and investigated the characteristics. It was used XRD, AES, SEM, and HP-4145B semiconductor parameter analyzer to analysis deposited AlN thin films. The deposition conditions for the good c-axis orientation were 100 W of RF power, $200^{\circ}C$ of substrate temperature and 15 mTorr of working pressure. The leakage current density was less then $1.3{\times}10^{-7}A/cm^{2}$. And it was also investigated the etching properties of deposited AlN thin films for application.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.391-392
• /
• 2012

In these days, the desire for the precise and tiny displays in mobile application has been increased strongly. Currently, laser displays ranging from large-size laser TV to mobile projectors, are commercially available or due to appear on the market [1]. In order to achieve a mobile projectors, the semiconductor laser diodes should be used as a laser source due to their size and weight. In this presentation, the continuous etch characteristics of Pd and AlGaN/GaN superlattice for the fabrication of blue laser diodes were investigated by using inductively coupled $CHF_3$ and $Cl_2$ -based plasma. The GaN laser diode samples were grown on the sapphire (0001) substrate using a metal organic chemical vapor deposition system. A Si-doped GaN layer was grown on the substrate, followed by growth of LD structures, including the active layers of InGaN/GaN quantum well and barriers layer, as shown in other literature [2], and the palladium was used as a p-type ohmic contact metal. The etch rate of AlGaN/GaN superlattice (2.5/2.5 nm for 100 periods) and n-GaN by using $Cl_2$ (90%)/Ar (10%) and $Cl_2$ (50%)/$CHF_3$ (50%) plasma chemistry, respectively. While when the $Cl_2$/Ar plasma were used, the etch rate of AlGaN/GaN superlattice shows a similar etch rate as that of n-GaN, the $Cl_2/CHF_3$ plasma shows decreased etch rate, compared with that of $Cl_2$/Ar plasma, especially for AlGaN/GaN superlattice. Furthermore, it was also found that the Pd which is deposited on top of the superlattice couldn't be etched with $Cl_2$/Ar plasma. It was indicating that the etching step should be separated into 2 steps for the Pd etching and the superlattice etching, respectively. The etched surface of stacked Pd/superlattice as a result of 2-step etching process including Pd etching ($Cl_2/CHF_3$) and SLs ($Cl_2$/Ar) etching, respectively. EDX results shows that the etched surface is a GaN waveguide free from the Al, indicating the SLs were fully removed by etching. Furthermore, the optical and electrical properties will be also investigated in this presentation. In summary, Pd/AlGaN/GaN SLs were successfully etched exploiting noble 2-step etching processes.