• 열처리공학회지
• /
• 제21권1호
• /
• pp.3-9
• /
• 2008

Al-Co-N thin films, Al-Co-N/Al-N and Al-Co-N/Al-Co multilayers containing various amounts of Co content were deposited by using a two-facing targets type dc sputtering (TFTS) system. The films were also annealed successively and isothermally at different annealing temperatures. Irrespective of Co content and preparation methods, all the as-deposited films were observed non-magnetized. It was found that annealing conditions can control the magnetic and electrical properties as well as the microstructure of the films.

• 한국재료학회지
• /
• 제18권10호
• /
• pp.558-563
• /
• 2008

TiAlN films were deposited on WC-5Co substrates with different buffer layers by D.C. magnetron sputtering. The films were evaluated by microstructural observations and measuring of preferred orientation, hardness value, and adhesion force. As a process variable, various buffer layers were used such as TiAlN single layer, TiAlN/TiAl, TiAlN/TiN and TiAlN/CrN. TiAlN coating layer showed columnar structures which grew up at a right angle to the substrates. The thickness of the TiAlN coating layer was about $1.8{\mu}m$, which was formed for 200 minutes at $300^{\circ}$. XRD analysis showed that the preferred orientation of TiAlN layer with TiN buffer layer was (111) and (200), and the specimens of TiAlN/TiAl, TiAlN/CrN, TiAlN single layer have preferred orientation of (111), respectively. TiAlN single layer and TiAlN/TiAl showed good adhesion properties, showing an over 80N adhesion force, while TiAlN/TiN film showed approximately 13N and the TiAlN/CrN was the worst case, in which the layer was destroyed because of high internal residual stress. The value of micro vickers hardness of the TiAlN single layer, TiAlN/TiAl and TiAlN/TiN layers were 2711, 2548 and 2461 Hv, respectively.

• 대한금속재료학회지
• /
• 제50권3호
• /
• pp.248-255
• /
• 2012

AlN thin films containing various amounts of Co, AlN-Co, and Al-Co alloy particles were prepared using a two-facing-target type dc reactive sputtering (TFTS) system. The as-deposited films exhibited the variable nature expected from an AlN-rich phase, and an amorphous-like phase, depending on the Co content in the films. Specific favorable microstructures were prepared by optimizing annealing conditions. Those microstructures and their magnetic properties and resistivity were investigated. As-deposited films showed very small saturation magnetization and an amorphous-like structure. However, when annealed, the as-deposited amorphous-like phase decomposes into phases of AlN, Co and Al-Co. These annealing induced changes in the microstructure improve the magnetization and resistivity of the films. Further improvement of soft magnetic properties could lead to the material being used for high density magnetic recording head material.

• 한국표면공학회지
• /
• 제35권6호
• /
• pp.408-414
• /
• 2002

TiN and TiAlN coating layer were deposited on WC-Co steel substrates by an arc ion plating(AIP) technique. The crystallinity and morphology for the deposited coating layers were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The impact behaviors of the deposited TiN and TiAlN coating layer were investigated with a ball-on-plate impact tester. Beyond $10^2$ impact cycle, TiAlN coating layer showed superior impact wear resistance compared to TiN coating layer. On the other hand, both TiN and TiAlN coating layers started to be partially failed between $10^2$ and $10^3$ impact cycle. Above $10^3$ impact cycle, TiN and TiAlN coating layers showed similar impact behavior because of the substrate effect.

• 한국가스학회지
• /
• 제20권2호
• /
• pp.1-9
• /
• 2016

본 연구는 플라즈마/촉매 공정을 이용하여 n-헵테인과 일산화탄소의 동시제거에 대해 조사하였다. n-헵테인과 일산화탄소의 분해특성을 파악하기 위해 플라즈마/촉매 공정과 촉매공정의 분해효율을 비교하였고, 촉매의 종류, 온도, 전력 등을 변화시켜 실험을 진행하였다. n-헵테인의 분해효율은 반응기 내부의 온도보다는 에너지밀도에 더 영향을 많이 받는 것으로 확인되었으며, 일산화탄소는 에너지밀도와 반응기 내부 온도 모두의 영향을 받는 것으로 나타났다. 촉매의 종류를 달리하며 n-헵테인의 분해효율을 조사한 결과 $Pd/{\gamma}-Al_2O_3$ > $Ru/{\gamma}-Al_2O_3{\approx}Ag/{\gamma}-Al_2O_3$순으로 나타났다. 특히, $Pd/{\gamma}-Al_2O_3$를 사용한 경우 n-헵테인 분해 과정에서 일산화탄소가 거의 발생하지 않았으며, $CO_2$ 선택도가 100%에 가까웠다. 일산화탄소 분해효율은 $Pd/{\gamma}-Al_2O_3$ > $Ru/{\gamma}-Al_2O_3$ > $Ag/{\gamma}-Al_2O_3$ 순으로 나타났으며, $180^{\circ}C$이하의 온도에서는 플라즈마/촉매 공정의 효율이 높고, $180^{\circ}C$이상에서는 촉매 공정의 분해효율이 높았다.

• 한국전기전자재료학회논문지
• /
• 제28권11호
• /
• pp.711-714
• /
• 2015

In this paper, high quality AlN layers were regrown on AlN nanopillar structure with $SiO_2$-dots by HVPE. Surface morphology of AlN layer regrown exhibited flatter than a conventional AlN template. The laterally overgrown AlN regions would consist of a continuous well coalesced layer with lower dislocation density than in the template because of the dislocation blocking and dislocation bending effects. Moreover, result of Raman spectroscopy suggest that the AlN nanopillar structure with $SiO_2$-dots relieves the strain in the AlN layer regrown by HVPE.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2003년도 하계학술연구발표회 및 한.일 공동심포지엄
• /
• pp.21-21
• /
• 2003

Microstructure and magnetic transport phenomina in rf sputtered AlN/Co type ten-layered discontinuous films of nanoscaled [AlN (3 nm)/Co (t nm)]...$\sub$10/ with t$\sub$Co/=1.0∼2.0 nm have been investigated. The microstructure and tunneling magnetic resistance of the samples are strongly dependent on the thickness of Co layer. Negative tunneling magneto-resistance due to the spin-dependent transport has been observed along the current-in-plane configuration in the samples having the Co layers below 1.6 nm thick. When the thickness of Co layer was less than 1,2 nm, randomly oriented granular Co particles were completely isolated and embedded in amorphous AlN matrix, and the films showed the superparamagnetic behavior with a high MR value of Δ$\rho$/$\rho$$\sub$0/=1.8 %. As t$\sub$Co/ increases, a transition from the regime of co-existence of superparamagnetic and ferromagnetic behaviors to ferromagnetic behavior was observed. Tunneling barrier called "decay length for tunneling" for the films having the thickness of Co layer from 1.4 to 1.6 nm was measured to be ranged from 0.004 to 0.021 ${\AA}$$\^$-1/.

• 한국표면공학회지
• /
• 제57권1호
• /
• pp.14-21
• /
• 2024

For this study, CrAlN multilayer coatings were deposited on SKD61 substrates using a multi-arc ion plating technique. The structural characteristics of the CrAlN multilayer coatings were evaluated using X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM). Additionally, the adhesion of the coatings was assessed through scratch testing, and the mechanical strength was evaluated using nanoindentation and tribometric tests for frictional properties. The results show that the CrAlN multilayer coatings possess a uniform and dense structure with excellent mechanical strength. Hardness measurements indicated that the CrAlN coatings have high hardness values, and both the coating adhesion and wear resistance were found to be improved compared to CrN. The addition of aluminum is anticipated to contribute to enhanced durability and wear resistance.

• 열처리공학회지
• /
• 제23권6호
• /
• pp.331-337
• /
• 2010

Aluminum nitride (AlN) thin films containing various amounts of Co content have been deposited by using a two-facing targets type sputtering (TFTS) system. The deposited films were also annealed successively and isothermally at different temperatures. Annealing treatment can control the physical properties as well as the microstructure of AlN films with Co particles. High magnetization and high resistivity are obtainable in AlN films containing dispersed Co particles. The coercivity of the films does not depend on annealing time, but it increases with increasing annealing temperature due to the increase of the grain size. A high saturation magnetization of 46 kG and resistivity of 2200 ${\mu}{\Omega}$-cm was obtained for AlN films containing 25 at% Co.

• 열처리공학회지
• /
• 제24권1호
• /
• pp.16-22
• /
• 2011

Al-Co/AlN-Co multilayer films with different layer thicknesses were prepared by using a two-facing target type D.C sputtering (TFTS) system. The deposited films were annealed isothermally at different temperatures and their microstructure, magnetic properties and resistivity were investigated. The magnetization of as-deposited films is very small irrespective of layer thickness. It was found that annealing conditions and layer thickness ratio (LTR) of Al-Co to AlN-Co can control the microstructure as well as the physical properties of the prepared films. The resistivity and magnetization increase and the coercivity decreases with decreasing LTR. High resistivity and sufficient magnetization were obtained for the films with LTR = 0.35. Films having such considerable magnetization and resistivity will be a potential candidate to be used for a high density recording material.