• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.4
• /
• pp.428-435
• /
• 2015

This paper presents the experimental study of cabin thermal comfort using a cold storage heat exchanger in a vehicle air-conditioning system. Recent vehicle-applied ISG functions for fuel economy and emission, but when vehicles stop, compressors in the air-conditioning system stop, and the cabin temperature sharply increases, making passengers feel thermal discomfort. This study conducts thermal comfort evaluation in the vehicle, which is applied to a cold storage system for the climate control wind tunnel test and the vehicle fleet road test with various airflow volume rates and ambient temperatures blowing to the cold storage heat exchanger. The experimental results, in the cold storage system, air discharge temperature is $3.1-4.2^{\circ}C$ lower than current air-conditioning system when the compressor stops and provides cold air for at least 38 extra seconds. In addition, the blowing airflow volume to the cold storage heat exchanger with various ambient temperature was examined for the control logic of the cold storage system, and in the results, the airflow volume rate is dominant over the outside temperature. For this study, a cold storage system is economically useful to keep the cabin at a thermally comfortable level during the short period when the engine stops in ISG vehicles.

• Journal of Biosystems Engineering
• /
• v.36 no.3
• /
• pp.204-210
• /
• 2011

This study developed the cyclone conveying system using roughage cutter for the round bale reported in the previous papers. Performance tests were conducted whether it can easily separate dust from roughage such as rice straws and it can transport roughages from cutter to TMR mixer. In addition, the airflow patterns in the cyclone conveying system were investigated using CFD code (FLUENT 6.2) for various velocities of dust collection fan. The cyclone conveying system was designed based on dried rice straws with a diameter of 1,340 mm, a cylinder length of 1,220 mm, a cone length of 850 mm and the current velocity of the dust collection fan was 15~20 m/s. It was found that transporting of roughage from cutter to TMR mixer and the separation of dust were satisfactory, and the dust removal rate of rice straws was around 31.9%. CFD analysis showed that, at the blowing fan velocity of 11.6 m/s, the airflow velocity inside the dust collector increased as velocity of the dust collection fan increased, but the airflow patterns inside the dust collector were all much the same.

• Tunnel and Underground Space
• /
• v.28 no.6
• /
• pp.609-619
• /
• 2018

This study was carried out at a local limestone mine to analyze the ventilation efficiency of the shaft equipped with a main fan. The results show that its ventilation efficiency is clearly verified for the natural as well as the mechanical ventilation. The airflow rate of $11.7m^3/s$ was induced by the natural ventilation force and the maximum quantity is almost same as the airflow rate estimated by monitoring the average temperatures in the upcast and downcast air columns. Meanwhile, the airflow rate exhausted by the main fan through the shaft was $20.3{\sim}24.8m^3/s$; variation of the quantity was caused by the upward shift of the mine ventilation characteristic curve due to the frequent movement of the equipment. This indicates efforts are required to reduce the ventilation resistance and raise the quantity supplied by the main fan. The turbulent diffusion coefficients along the 1912 m long airway from the portal to the shaft bottom was estimated to be $15m^2/s$ and $18m^2/s$. Since these higher coefficients imply that contaminants will be dispersed at a faster velocity than the airflow, prompt exhaust method should be planned for the effective air quality control. The ventilation shaft and main fan are definitely what local limestone mines inevitably need for better working environment and sustainable development.

• Fibers and Polymers
• /
• v.7 no.3
• /
• pp.317-322
• /
• 2006

Reduction of yam hairiness by nozzles in ring spinning and winding is a new approach. Simulation of the airflow pattern inside the nozzles provides useful information about actual mechanism of hairiness reduction. The swirling air current inside the nozzles is capable of wrapping the protruding hairs around the yam body, thereby reducing yam hairiness. Since production rate of winding is very high and the process itself increases yarn hairiness any method to reduce the hairiness of yarns at this stage is a novel approach. A CFD (computational fluid dynamics) model has been developed to simulate the airflow pattern inside the nozzles using Fluent 6.1 software. In this study, both S- and Z-type nozzles having an axial angle of 500 and diameter of 2.2 mm were used for simulation studies. To create a swirling effect, four air holes of 0.4 mm diameter are made tangential to the inner walls of the nozzles. S- and Z-twisted yams of 30 tex were spun with and without nozzles and were tested for hairiness, tensile and evenness properties. The total number of hairs equal to or exceeding 3 mm (i.e. the S3 values) for yam spun with nozzle is nearly 49-51 % less than that of ring yams in case of nozzle-ring spinning, and 15 % less in case of nozzle-winding, while both the yarn types show little difference in evenness and tensile properties. Upward airflow gives best results in terms of hairiness reduction for nozzle-ring and nozzle wound yams compared to ring yarns. Yarn passing through the centre of the nozzle shows maximum reduction in S3 values.

• Fire Science and Engineering
• /
• v.31 no.1
• /
• pp.1-9
• /
• 2017

This study conducted Testing, Adjusting, and Balancing (TAB), which is a type of field performance evaluation experiment of a zone smoke-control system, at a railway underground transit passage installed with a zone smoke- control system to find problems and improvements for ensuring performance. TAB for the smoke control system was classified into several procedures, such as design data review, duct leakage test, field measurement of the airflow rate, velocity of the fan and duct, and a smoke test. Through the duct leakage test, the system leakage ratio was examined to prove the duct sealing. The iImprovement of the smoke control airflow problems due to the lack of fan static pressure loss was the secured performance. The performance of the smoke control fan was secured by improvements of the smoke control airflow rate problems caused by the loss of static pressure in the intake duct. The smoke test in the smoke control zone confirmed that the damper operating schedule subject was influenced by natural wind or train wind.

• Journal of computational fluids engineering
• /
• v.3 no.1
• /
• pp.82-88
• /
• 1998

As a par of a project related to the development of the design algorithm of a compact heat exchanger for the application of the electronic home appliances, the effect of the discreteness of the airflow boundary generated on the cooling fin surface on the heat transfer and pressure drop characteristics of the heat exchanger was studied numerically. In general, there are two critical design parameters seriously considered in the design of the heat exchanger; heat transfer rate(Q) and pressure drop coefficient(C/sub p/). Even though the higher heat transfer rate with lower pressure drop characteristics is required in a design of the heat exchanger, it is not an easy job to satisfy both conditions at the same time because these two parameters are phenomenally inversely proportional. To control the boundary layer thickness and its length along the streamline, the surface of the flat fin was modified to accelerate the heat transfer rate on the fin surface. To understand the effect of the discreted fin size(S/sub w/) and its location(S/sub h/) on the performance of the heat exchanger in the airflow field, the flat fin was modified as shown in Fig. 1. From this study, it was found that the smaller and more number of slits on the fin surface showed the higher energy diffusion rate. It means that the discreteness of the boundary layer is quite important on the heat transfer rate of the heat exchanger. On the other hand, if the fin surface configuration is very complex than needed, higher static pressure drop occurs than required in a system and it may be a reason of the induced aerodynamic noise in the heat exchanger.

• Journal of Animal Environmental Science
• /
• v.11 no.1
• /
• pp.55-60
• /
• 2005

This study was conducted to determine the odor reduction efficiency of a biofilter desist using different filter materials. The summary of results are as follows; 1. The airflow penetration rate of the different filter materials namely; rice straw, woodchips, rice hulls and sawdust were 0.72 m/s, 0.64 m/s, 0.48 m/s and 0.17 m/s, respectively. 2. The elimination of $NH_3$ gas was fastest in the rice hull at a rate of 4 mg/${\iota}$ followed by sawdust, woodchips and rice straw at 3 mg/${\iota}$, 3 mg/${\iota}$ and 7 mg/${\iota}$, respectively. 3. The filter material made of wood chips was able to eliminate the offensive gas known as $H_2S$ at a rate of 2.2 mg/${\iota}$ on the 7th day, 17.6 mg/${\iota}$ on the 21st day but decreased to 10.7 mg/${\iota}$ on the 36th day. In contrast, the filter material composed of sawdust had a continuous increase in the reduction of $H_2S$ at a rate of 12.3 mg/${\iota}$ on the 7th day, 18.3 mg/${\iota}$ on the 21st day and 20.1 mg/${\iota}$ on the 36th day. The above findings indicated that among the filter materials, sawdust was the most effective in absorbing $H_2S$. Airflow penetration rate can be related to $H_2S$ odor elimination efficiency as shown by the slowest airflow rate of sawdust which is only 0.17 m/s.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.5
• /
• pp.14-20
• /
• 2020

In this study, the overall states of the airflow when a truck with or without side pairing is driven at a maximum speed of 90 km/h, regulated by domestic law, were investigated through computational fluid dynamics numerical analysis. All the tested models showed that the airflow went under the truck body; specifically, the air did not flow along the underside to the rear of the truck but through the sides of its underside. The drag with the drag coefficient at model 3 was clearly higher than those for the other two models. The results of this study could help to improve the truck performance by reducing its resistance against the air flown from it in driving itself.

• Phonetics and Speech Sciences
• /
• v.6 no.3
• /
• pp.57-62
• /
• 2014

The present study was performed to investigate and discuss the aerodynamic characteristics of whispered and normal speech during reading paragraph tasks. 39 normal females(18-23 yrs.) read 'Autumn' paragraph with whispered and normal phonation. Their readings were recorded and analyzed by 'Running Speech' in Phonatory Aerodynamic System(PAS) instrument. As results, during whispered speech, the total duration was longer and the numbers of inspiration were more frequently shown than normal speech. The Peak expiratory and inspiratory rate were higher in normal speech, but the expiratory and inspiratory volume were higher in whispered speech. By correlation analysis, both whispered and normal speech showed significantly high correlation between total duration and expiratory/inspiratory airflow duration; numbers of inspiration and inspiratory airflow duration; expiratory and inspiratory volume. These results show that whispered speech needs more respiratory effort but shows poorer aerodynamic efficacy during phonation than normal speech.

• Journal of the Semiconductor & Display Technology
• /
• v.9 no.4
• /
• pp.71-76
• /
• 2010

According to recent changes in industry for semiconductor devices, a low-temperature treatment has become a necessity. These changes relate to size refinement and the development of new materials. While variation in cooling efficiency does not affect the yield when using a high-temperature treatment, uniform cooling efficiency is necessary avoid "inconsistencies/bends" in low temperature treatments. However it is difficult to increase temperature stabilization in low temperature treatments. In this paper, using CFD (Computer Fluid Dynamics), we analyze and manipulate the design and input of the low-temperature system to attempt to control for temperature variations within the quartz tube, of which airflow appears to be a predominant factor. This simulation includes variable inputs such as airflow rate, head pressure, and design manipulations in the S.C.U. (Super Cooling Unit).