• Journal of Advanced Marine Engineering and Technology
• /
• 제37권7호
• /
• pp.737-742
• /
• 2013

Recently, unmanned aircrafts for safe measurement in hazardous locations have been developed. In a method of operation of unmanned aircraft vehicles (UAV), there are two methods of manual control and automatic control. Small UAVs are used for low altitude surveillance flights where unknown obstacles can be encountered. Obstacle avoidance is one of the most challenging tasks which the UAV has to perform with high level of accuracy. In this study, we used a laser range finder as an obstacle detector in automatic navigation of unmanned aircraft to patrol the destination automatically. We proposed a system to avoid obstacles automatically by measuring the angle and distance of the obstacle using the laser range finder.

• 한국항공운항학회지
• /
• 제18권4호
• /
• pp.21-29
• /
• 2010

The main purpose of this study is to obtain linear models for the design of automatic flight controller in order to operate the Light Sport Aircraft as unmanned air vehicle. Flight test equipments installed on the aircraft to acquire flight test data are described and maneuvers for practical speed calibration are introduced. Parameters for the linear models of lateral and longitudinal motion are estimated by the Output error method as well as trim data analysis using the flight test data. Simulated data using the estimated parameters is shown to agree well with the measurement data. Estimated parameters obtained for several flight conditions can be used to improve the aerodynamic database of the simulation program.

• International Journal of Aeronautical and Space Sciences
• /
• 제7권1호
• /
• pp.73-83
• /
• 2006

In this paper, a redundancy management system for aircraft is studied, and fault detection and isolation algorithms of inertial sensor system are proposed. Contrary to the conventional aircraft systems, UAV system cannot allow triple or quadruple hardware redundancy due to the limitations on space and weight. In the UAV system with dual sensors, it is very difficult to identify the faulty sensor. Also, conventional fault detection and isolation (FDI) method cannot isolate multiple faults in a triple redundancy system. In this paper, two FDI techniques are proposed. First, hardware based FDI technique is proposed, which combines a parity equation approach with a wavelet based technique. Second, analytic FDI technique based on the Kalman filter is proposed, which is a model-based FDI method utilizing the threshold value and the confirmation time. To provide the reference value for detecting the fault, residuals are calculated using the extended Kalman filter. To verify the effectiveness of the proposed FDI methods, numerical simulations are performed.

• International Journal of Aerospace System Engineering
• /
• 제5권1호
• /
• pp.9-18
• /
• 2018

The longitudinal flight parameters of a light airplane are estimated from flight test data by use of the output error method. The reliability of the flight test measurement is examined in engineering judgment, scatter and Cramer-Rao bound, which turns out to be satisfactory with minor defects. Estimated parameter values are validated by comparing the simulated responses with the ones from actual flight tests. The FTD(Flight Training Device) of a light airplane turns out to satisfy the qualification of FAA Level 5 FTD in longitudinal motion. All the necessary practices for generation of high-fidelity data in longitudinal motion of a light aircraft are successfully performed in this study.

• International Journal of Aeronautical and Space Sciences
• /
• 제18권3호
• /
• pp.535-544
• /
• 2017

In-flight aircraft engine performance estimation is one of the key techniques for advanced intelligent engine control and in-flight fault detection, isolation and accommodation. This paper detailed the current performance degradation estimation methods, and an improved hybrid Kalman filter via velocity-based LPV (VLPV) framework for these needs is proposed in this paper. Composed of a nonlinear on-board model (NOBM) and VLPV, the filter shows a hybrid architecture. The outputs of NOBM are used for the baseline of the VLPV Kalman filter, while the system performance degradation factors on-line estimated by the measured real system output deviations are fed back to the NOBM for its updating. In addition, the setting of the process and measurement noise covariance matrices' values are also discussed. By applying it to a commercial turbofan engine, simulation results show the efficiency.

• 한국항공운항학회지
• /
• 제26권2호
• /
• pp.76-82
• /
• 2018

A test simulator is needed to develop a fuel quantity measurement system that takes into account the roll and pitch motion of the aircraft. In this paper, we develop a test simulator that consists of attitude simulation equipment, fueling equipment, and data storage equipment. The attitude simulation equipment simulates the aircraft attitude. It is manufactured to operate pitch angle and roll angle movement. The fueling equipment supplies fuel to the supplementary fuel tank. The data storage equipment collects and stores the measured data. We also develop an automation software that operates the test simulator and collects data automatically. The test simulator has been automated to prevent testers from being exposed to toxic fuel. Through automation software, the collection period is reduced by one quarter compared to manual collection. The developed fuel quantity measurement system is verified through the test simulator.

• 한국대기환경학회지
• /
• 제13권5호
• /
• pp.361-369
• /
• 1997

In order to investigate the abundance and transboundary fluxes of air pollutants over the Yellow Sea, airborne measurements were made aboard the SF-600 aircraft (Pan-Asia Engineering) in March, 1996. The data presented in this paper are preliminary results and airborne experiment will be carried out until 1999. The vertical profile of relevant meteorological parameters such as temperature, water vapor, wind direction and wind speed were also observed at Taean. Mixing layer height was about 1000~1100m during the flights. The SO$_2$ and NO$_{x}$ concentrations were 3~6 ppb and 5~7 ppb below 1000 m, within 1 ppb and 3~5 ppb at 1000~2000m, respectively. Backward trajectory analyses were also carried out. A mathematical method by Lelieveld et al.(1989) was used to estimate the flux of air pollutants through the planetary boundary layer of Yellow Sea area. Transboundary fluxes were calculated using the measurement results with respect to the pollutants concentration, depth of the planetary boundary layer, wind speed and wind direction. The estimated transboundary flux of SO$_2$through the western boundary of Korea was about 39~42 tons/hour.r.

• 한국산업보건학회지
• /
• 제30권2호
• /
• pp.174-184
• /
• 2020

Objectives: The purpose of this study was to improve the working environment by identifying the work satisfaction of the cleaning workers of the aircraft and measuring and assessing the harmful factors of the cleaning process. Methods: We asked 23 cleaning companies for questionnaires and got 100 answers from 5 companies. The A-E Airline health manager has been contacted to establish a site survey schedule. The in-flight and lounge were measured using direct reading equipment. The harmful factor to be measured are noise, dust, temperature, volatile organic compound, total airborne bacteria, and total airborne bacteria. Results: Uncomfortable positions when replacing blanket, cleaning the table, and cleaning the floor have been identified as factor that reduce work satisfaction. Noise when replacing newspapers and cleaning toilets has been identified as a factor that lowers work satisfaction. Temperature and humidity were found to reduce work satisfaction during in-flight disinfection. Measurements of aircraft cabin and lounge with direct read equipment have shown that none of the items exceed the exposure criteria. Conclusions: As a result of measuring direct-reading equipment, no items exceeded the exposure criteria for each harmful factor. A clear survey of the working environment is required based on the results, and additional research is needed using personal sample measurement.

• International Journal of Aeronautical and Space Sciences
• /
• 제16권4호
• /
• pp.581-589
• /
• 2015

This paper describes a monocular vision-based formation flight technology using two fixed wing unmanned aerial vehicles. To measuring relative position and attitude of a leader aircraft, a monocular camera installed in the front of the follower aircraft captures an image of the leader, and position and attitude are measured from the image using the KLT feature point tracker and POSIT algorithm. To verify the feasibility of this vision processing algorithm, a field test was performed using two light sports aircraft, and our experimental results show that the proposed monocular vision-based measurement algorithm is feasible. Performance verification for the proposed formation flight technology was carried out using the X-Plane flight simulator. The formation flight simulation system consists of two PCs playing the role of leader and follower. When the leader flies by the command of user, the follower aircraft tracks the leader by designed guidance and a PI control law, and all the information about leader was measured using monocular vision. This simulation shows that guidance using relative attitude information tracks the leader aircraft better than not using attitude information. This simulation shows absolute average errors for the relative position as follows: X-axis: 2.88 m, Y-axis: 2.09 m, and Z-axis: 0.44 m.

• 한국측량학회지
• /
• 제23권2호
• /
• pp.205-210
• /
• 2005

산업이 발달됨에 따라 산업 제품들은 대형화되고 더욱 정밀화 되고 있다. 생산자들은 제품이 요구에 맞게 정밀하게 제작되었는가를 확인할 수 있는 방법이 필요하게 되었고 이러한 이유로 대상물에 접촉을 하지 않으면서 신속하고 정밀한 데이터를 취득할 수 있는 산업사진측량기법이 관심을 끌게 되었다. 따라서 본 연구에서는 산업제품들의 정밀도를 검사하기 위한 방법으로 산업사진측량의 적용성을 알아보기 위하여 O-2A 항공기를 대상으로 실험을 실시하였다. 항공기의 정렬상태를 확인하기 위한 검사점사이의 거리 측정과 변형이 발생하였을 것으로 추정되는 부분의 변형량을 프로젝트 타겟을 이용하여 변형량을 정량적으로 해석함으로써 항공기 정비 및 사고분석 등에 필요한 데이터를 신속히 제공할 수 있었다.