• Journal of Advanced Navigation Technology
• /
• v.24 no.1
• /
• pp.1-8
• /
• 2020

In this research, we develop an airborne equipment radiating S/C-band signal to a target located at a long distance. RF interface of the equipment comprises band-specific transmitters and an broadband antenna to satisfy EIRP(effective isotropic radiated power) requirements. The equipment is in a shape of a POD like an aircraft fuel tank. The measured weight of the equipment is 119.8 kg, the CG(center of gravity) is 1391.35 mm and the MOI(moment of inertia) are 46.07 ± 0.05(I_yy) kg·㎡, 45.36 ± 0.09(I_zz) kg·㎡. All results are found to meet the requirements for aircraft installation. To verify flight safety, EMI(electromagnetic interference) tests (RE102, CE102), environmental tests (high/low temperature operation, altitude), intra-system EMC(electromagnetic compatibility) and HERP(hazards electromagnetic radiation personnel) tests have been conducted and all the test results met the requirements. It is confirmed that the equipment could be mounted on the aircraft by meeting all electrical and mechanical requirements.

• Journal of Advanced Navigation Technology
• /
• v.25 no.5
• /
• pp.377-383
• /
• 2021

In this paper, we describe the case of automatic test equipment development for hardware verification of stores management computer mounted on aircraft. Recently, the required functions of aircraft have been diversified and the related technologies of avionics equipment have developed, and the types and quantity of interfaces required for avionics equipment have increased. In addition to the existing old stores, the stores management computer also needs to control the interface in large quantities as the requirements for the new stores are added. For this reason, the time and manpower required for the inspection of avionic equipment are also increasing, and if the test process of avionic equipment can be automated and unmanned, more efficient inspection system operation will be possible. Therefore, this paper introduces the case of designing test software and test scenario to automate the structural design contents and verification process of test equipment required for the verification of hardware function of stores management computer.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.1
• /
• pp.108-114
• /
• 2021

AVTE(Air Vehicle Test Equipment) is a device to check status of on-board aircraft equipment before and after flight for performing successful UAV(Unmanned Aerial Vehicle) missions. This paper describes software design and test sequence of the AVTE for enabling easy-manual check by the operator and convenient automatic check of on-board electric equipment respectively. The proposed AVTE inspects BIT(Built-In Test) results of on-board LRUs(Line Replacement Units) including avionics and sensor sub-system devices. Also, it monitors all the LRU status and check the normality of aircraft equipment by means of setting specific values of the LRUs and confirming the expected test results. The AVTE prints the test results as a form of report to easily check the normal conditions of the aircraft equipment and operates automatically without operator interaction, thus being thought to effectively reduce workload of the operator.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.26 no.2
• /
• pp.76-82
• /
• 2018

A test simulator is needed to develop a fuel quantity measurement system that takes into account the roll and pitch motion of the aircraft. In this paper, we develop a test simulator that consists of attitude simulation equipment, fueling equipment, and data storage equipment. The attitude simulation equipment simulates the aircraft attitude. It is manufactured to operate pitch angle and roll angle movement. The fueling equipment supplies fuel to the supplementary fuel tank. The data storage equipment collects and stores the measured data. We also develop an automation software that operates the test simulator and collects data automatically. The test simulator has been automated to prevent testers from being exposed to toxic fuel. Through automation software, the collection period is reduced by one quarter compared to manual collection. The developed fuel quantity measurement system is verified through the test simulator.

• Journal of Internet Computing and Services
• /
• v.23 no.1
• /
• pp.113-124
• /
• 2022

In wartime conditions, the communication system of military aircraft is exposed to jamming, and it is necessary to mount communication equipment with high anti-jamming performance in order to perform air operations smoothly even in an environment where jamming attempts are made. In this paper, we check in detail the jamming and anti-jamming technology that can be applied to wireless communication, and the data disclosed on the difference in specifications of the next-generation anti-jamming radio with frequency hopping method and the improvement of anti-jamming performance according to these changes. It was briefly analyzed within the scope. In addition, the points to be considered when designing a new domestic aircraft and the possibility of installing the next-generation anti-jamming communication equipment on the currently operating aircraft were confirmed, and the tactical usefulness of improving the anti-jamming capability of the next-generation anti-jamming communication equipment was confirmed.

• Journal of Advanced Navigation Technology
• /
• v.22 no.2
• /
• pp.64-69
• /
• 2018

Automatic test equipment for field maintenance of aircraft mounted equipment is effective for integrated design when operating a small number of aircraft for special purposes. The integrated automatic test equipment identifies commonly used interfaces and is used for branching or generating routes for each unit under test specific inspection. High-precision signals such as RTD, TC, and analog voltage can cause measurement errors due to conduction resistance during signal branching and connection when generating branches and paths. The measurement error caused by the resistance of the wire leads to a lot of restrictions in designing the equipment to be inspected. In this paper, we propose a method of calibrating highly accurate signals of an integrated automatic inspection equipment that minimizes measurement errors of analog voltage and high - precision signals.

• Smart Structures and Systems
• /
• v.1 no.2
• /
• pp.159-184
• /
• 2005

The paper intends to summarize some guidelines for future smart structure system application in military aircraft. This preview of system integration is based upon a review on approximately one and a half decades of application oriented aerospace related smart structures research. Achievements in the area of structural health monitoring, adaptive shape, adaptive load bearing devices and active vibration control have been reached, potentials have been identified, several feasibility studies have been performed and some smart technologies have been already implemented. However the realization of anticipated visions and previously initial timescales announced have been rather too optimistic. The current development shall be based on a more realistic basis including more emphasis on fundamental aircraft strength, stiffness, static and dynamic load and stability requirements of aircraft and interdisciplinary integration requirements and improvements of integrated actors, actuator systems and control systems including micro controllers.

• Proceedings of the Korean Reliability Society Conference
• /
• 2004.04a
• /
• pp.83-94
• /
• 2004

Businesses use a variety of equipment to produce output and services. Equipment unreliable - failure due to failure of one or more components. Most equipment are complex systems (a truck has more than 15,000 components, an aircraft has 4.5 million components)(omitted).

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.28 no.1
• /
• pp.115-121
• /
• 2020

Recently avionics equipment and its integration are most important part for implementing high performance aircraft system. This trends are emphasized in the military or special purpose aircraft development program. Flight Test Bed Aircraft (hereafter FTB A/C) - by modified commercial aircraft - was key solution to verify function and performance of avionics system for complex aircraft development program for a while, but there are no experience to use it in domestic airspace of ROK. This paper would like to address what act and regulation is necessary to perform flight operation of FTB A/C with keeping a airworthiness and airspace control policy. and then willing to propose what do we do for improving aviation industry.

• Nuclear Engineering and Technology
• /
• v.53 no.6
• /
• pp.1858-1868
• /
• 2021

Resisting an accidental impact of large commercial aircrafts is an important aspect of advanced nuclear power plant (NPP) design. Especially after the 9·11 event, some regulations were enacted, which required the design of NPPs should consider the accidental impact of large commercial aircrafts. Normal working of equipment is important for stopping reactor under an impact when an NPP is in operation. However, there is a lack of reliable analysis and research on the impact test of nuclear prototype equipment. Therefore, in order to study the response of the equipment under high acceleration impact, a centrifugal pump is selected as the research object to perform the impact test. A horizontal half-sinusoidal pulse wave was applied to the working pump. The test results show that the horizontal response of the motor and flange is greater compared to other parts, as well as the vertical response of the coupling. The stress response of the pump body support and motor support is high, hence these parts should be considered in the design of the pump. Finally, combined with the damage and stress evaluation results of the pump under different amplitudes, the ultimate impact acceleration that the pump can withstand is given.