• Advances in aircraft and spacecraft science
• /
• v.9 no.3
• /
• pp.169-193
• /
• 2022

By the present paper, both experimental and analytical models have been proposed to study the vibration behavior of partially bio-sourced sandwich panel with orthogonally stiffened core. For a variable mass fraction of Alfa fibers from 5% to 15%, impregnated in a Medapoxy STR resin, this panel were manufactured by molding the orthogonally stiffened core then attached it with both skins. Using simply supported boundary conditions, a free vibration test was carried out using an impact hammer for predicting the natural frequencies, the mode shapes and the damping coefficient versus the fibers content. In addition, an analytical model based on the Higher order Shear Deformation Theory (HSDT) was developed to predict natural frequencies and the mode shapes according to Navier's solution. From the experimental test, we have found that the frequency increases with the increase in the mass fraction of the fibers until 10%. Beyond this fraction, the frequencies give relatively lower values. For the analytical model, variation of the natural frequencies increased considerably with side-to-thickness ratio (a/H) and equivalent thickness of the core to thickness of the face (h_s/h). We concluded that, the vibration behavior was significantly influenced by geometrical and mechanical properties of the partially bio-sourced sandwich panel.

• Advances in aircraft and spacecraft science
• /
• v.3 no.3
• /
• pp.243-257
• /
• 2016

The increase of air traffic volume has brought an increasing amount of issues related to carbon and NOx emissions and noise pollution. Aircraft manufacturers are concentrating their efforts to develop technologies to increase aircraft efficiency and consequently to reduce pollutant discharge and noise emission. Ultra High By-Pass Ratio engine concepts provide reduction of fuel consumption and noise emission thanks to a decrease of the jet velocity exhausting from the engine nozzles. In order to keep same thrust, mass flow and therefore section of fan/nacelle diameter should be increased to compensate velocity reduction. Such feature will lead to close-coupled architectures for engine installation under the wing. A strong jet-wing interaction resulting in a change of turbulent mixing in the aeroacoustic field as well as noise enhancement due to reflection phenomena are therefore expected. On the other hand, pressure fluctuations on the wing as well as on the fuselage represent the forcing loads, which stress panels causing vibrations. Some of these vibrations are re-emitted in the aeroacoustic field as vibration noise, some of them are transmitted in the cockpit as interior noise. In the present work, the interaction between a jet and wing or fuselage is reproduced by a flat surface tangential to an incompressible jet at different radial distances from the nozzle axis. The change in the aerodynamic field due to the presence of the rigid plate was studied by hot wire anemometric measurements, which provided a characterization of mean and fluctuating velocity fields in the jet plume. Pressure fluctuations acting on the flat plate were studied by cavity-mounted microphones which provided point-wise measurements in stream-wise and spanwise directions. Statistical description of velocity and wall pressure fields are determined in terms of Fourier-domain quantities. Scaling laws for pressure auto-spectra and coherence functions are also presented.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.3
• /
• pp.253-260
• /
• 2016

This paper proposes a planar Log-Periodic Dipole Array(LPDA) antenna with light-weight supporting structure for installing on an aircraft. The proposed antenna is designed by applying a planar skeleton supporting structure that has light-weight for an aircraft and is capable of withstanding structural vibration. The material of the planar skeleton supporting structure is a Polyether ether ketone(Peek) which has excellent characteristics on strength and temperature. The proposed antenna is fabricated by attaching the radiating elements of the LPDA on both sides of the supporting structure. The changed input impedance due to the dielectric material of the supporting structure was compensated for by controlling the distance and length of several radiating elements. The 10-dB return loss bandwidths of the designed planar LPDA antenna with light-weight supporting structure are obtained as 0.4~3.1 GHz(7.3:1) in the simulation and 0.41~3.5 GHz(8.2:1) in the measurement. The average gains in 0.5~3 GHz band are 6.77 dBi in the simulation and 6.55 dBi in the measurement. Therefore, we confirm that the designed antenna is appropriate to be installed on an aircraft due to its light-weight structure and wideband directional radiation characteristics.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.4
• /
• pp.91-99
• /
• 2005

Flight compatibility certification is performed to substantiate the compatibility between ALQ-X ECM pod and KF-16D/RF-4C aircraft. A certification plan for the ALQ-X flight compatibility is established. Similarity analysis, mass/inertia analysis, structural analysis/test, and ground vibration test/flutter analysis are made to support the safety of MIL-HDBK-1763 Test 250 (Captive compatibility flight profile). Aircraft flew along flight envelope boundary with representative ALQ-X configurations. Handling qualities are evaluated by comparing flight characteristics of the aircraft with and without ALQ-X. Structural integrity and endurance is evaluated using measured flight test data. Results of these flight tests showed that ALQ-X is compatible with KF-16D/RF-4C without altering the flight envelope which has originally been certified for ALQ-88 and ALQ-119 ECM pods. ALQ-X certification program made following technical achievements: Type III certification for foreign designed fighter, flutter analysis program development using GVT results, and utilization of MIL-STD-1553B data bus in flight test.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.4
• /
• pp.415-422
• /
• 2016

When shock acceleration is applied to a mechanical system, it may cause malfunctioning and damage to the system. Hence, to prevent these problems when developing a gimbal structure system for observation reconnaissance, the MIL-STD-810G shock standard must be satisfied as a design specification. Rubber vibration isolators are generally assembled on the base of the system in order to reduce the shock transferred from the aircraft. It is difficult to analyze the transient behavior of the system accurately, because rubber has a nonlinear load-deformation curve. To treat the nonlinear characteristic of the rubber, bilinear approximation was introduced. Using this assumption, transient responses of the system under base shock acceleration were calculated by the finite element method. In addition, experiments with a true prototype were performed using the same conditions as the analytical model. Compared with experimental data, the proposed numerical method is useful for the transient analysis of gimbal structure systems, including rubber vibration isolators with nonlinear stiffness and damping.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.4
• /
• pp.409-415
• /
• 2011

A gimbal system in observation reconnaissance aircraft was fabricated by assembling many parts and bearings. This system consists of a camera module and a stabilization gimbal that supports the camera module. During the flight for recording images, the gimbal system experiences various accelerations with wide frequencies. Although base excitation of stabilization gimbal results in vibration of the camera module, the camera module must be able to capture the correct and clear image even while vibrating. Hence, it is important to know the natural frequencies and vibration modes of the gimbal system with the camera module. Considering bearings as spring elements, the vibration characteristic of the gimbal system was analyzed by finite element method. In addition, harmonic response analysis was performed to determine the correct transmissibility of acceleration for the camera module in the frequency range of 0-500 Hz.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.27 no.1
• /
• pp.1-7
• /
• 2024

Weather is one of the main causes of aircraft accidents, and among the phenomena caused by weather, icing is a phenomenon in which an ice layer is formed when an object exposed to an atmosphere below a freezing temperature collides with supercooled water droplets. If this phenomenon occurs in the rotor blades, it causes defects such as severe vibration in the airframe and eventually leads to loss of control and an accident. Therefore, it is necessary to foresee the icing situation so that it can ascend and descend at an altitude without a freezing point. In this study, vibration data in normal and faulty conditions was acquired, data features were extracted, and vibration was predicted through deep learning-based algorithms such as CNN, LSTM, CNN-LSTM, Transformer, and TCN, and performance was compared to evaluate blade icing. A method for minimizing operating loss is suggested.

• The Korean Journal of Air & Space Law and Policy
• /
• v.33 no.1
• /
• pp.45-79
• /
• 2018

An increase of airplanes and military aircraft operation lead to significant demanding of residential claims by people who live in nearby airports and military bases due to noise, vibration and residential damages caused by aircraft operations. In recent years, a plaintiff has filed a lawsuit against the defendant, claiming the prohibition of using claimant's possessed land as a helicopter landing route, and the Daejeon High Court was in favour of the plaintiff. Although the Supreme Court later dismissed the Appeal Court decision, it is necessary to discuss the case of setting flight prohibited zone. In Japan, the airport noise lawsuits have been filed for a long time, mainly by environmental groups. Unlike the case that admitted residential damages caused by noise, the Yokohama District Court for the first time sentenced a judgment of the prohibition of the flight. This ruling was partially changed in the appellate court and some of the plaintiffs' claims were adopted. However, the Supreme Court of Japan finally rejected such decision from appeal and district courts. Atsugi Base is an army camp jointly used by the United States and Japan, and residents, live nearby, claim that they are suffering from mental damage such as physical abnormal, insomnia, and life disturbance because of the noise from airplane taking off and landing in the base. An administrative lawsuit was therefore preceded in the Yokohama District Court. The plaintiff requested the Japan Self-Defense Forces(hereinafter 'JSDF') and US military aircraft to be prohibited operating. The court firstly held the limitation of the flight operation from 10pm to 6am, except unavoidable circumstance. The case was appealed. The Supreme Court of Japan dismissed the original judgment on the flight claim of the JSDF aircraft, canceled the first judgment, and rejected the claims of the plaintiffs. The Supreme Court ruled that the exercise of the authority of the Minister of Defense is reasonable since the JSDF aircraft is operating public flight high zone. The court agreed that noise pollution is such an issue for the residents but there are countermeasures which can be taken by concerned parties. In Korea, the residents can sue against the United States or the Republic of Korea or the Ministry of National Defense for the prohibition of the aircraft operation. However, if they claim against US government regarding to the US military flight operation, the Korean court must issue a dismissal order as its jurisdiction exemption. According to the current case law, the Korean courts do not allow a claimant to appeal for the performance of obligation or an anonymous appeal against the Minister of National Defense for prohibiting flight of military aircraft. However, if the Administrative Appeals Act is amended and obligatory performance litigation is introduced, the claim to the Minister of National Defense can be permitted. In order to judge administrative case of the military aircraft operation, trade-off between interests of the residents and difficulties of the third parties should be measured in the court, if the Act is changed and such claims are granted. In this connection, the Minister of National Defense ought to prove and illuminate the profit from the military aircraft operation and it should be significantly greater than the benefits which neighboring residents will get from the prohibiting flight of military aircraft.

• Advances in aircraft and spacecraft science
• /
• v.1 no.3
• /
• pp.291-310
• /
• 2014

An advanced model for the linear flutter analysis is introduced in this paper. Higher-order beam structural models are developed by using the Carrera Unified Formulation, which allows for the straightforward implementation of arbitrarily rich displacement fields without the need of a-priori kinematic assumptions. The strong form of the principle of virtual displacements is used to obtain the equations of motion and the natural boundary conditions for beams in free vibration. An exact dynamic stiffness matrix is then developed by relating the amplitudes of harmonically varying loads to those of the responses. The resulting dynamic stiffness matrix is used with particular reference to the Wittrick-Williams algorithm to carry out free vibration analyses. According to the doublet lattice method, the natural mode shapes are subsequently used as generalized motions for the generation of the unsteady aerodynamic generalized forces. Finally, the g-method is used to conduct flutter analyses of both isotropic and laminated composite lifting surfaces. The obtained results perfectly match those from 1D and 2D finite elements and those from experimental analyses. It can be stated that refined beam models are compulsory to deal with the flutter analysis of wing models whereas classical and lower-order models (up to the second-order) are not able to detect those flutter conditions that are characterized by bending-torsion couplings.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1996.04a
• /
• pp.361-369
• /
• 1996

The accurate prediction of modal parameters of a rotating blade is an important requirement in the assessment of the dynamics of a helicopter rotor. Indeed, predictions of flight loads and stability are normally dependent on initially predicting the undamped mode shapes. A measuring technique, known as Strain Pattern Analysis (SPA), appears to be the most successful technique for measuring the mode shapes of rotating blades. This method was developed to be used on actual aircraft so no attempt was made to measure rotating mode shapes directly in order to validate the SPA method. This report summarizes results from experimental investigations which were carried out to validate the SPA method for the prediction of aerodynamically damped modes of a rotating blade. A series of modal tests were carried out on two rotor models in which the non-rotating, undamped and aerodynamically damped rotating modes were measured directly (strain and displacement patterns). It is shown that the SPA method to be very successful in itself but there are a number of limitations in validating this technique. To provide data which could be used to confidently validate theoretical prediction codes, existing limitations should be addressed.