• Journal of Aerospace System Engineering
• /
• v.14 no.spc
• /
• pp.31-38
• /
• 2020

The aircraft system safety assessment, which is emphasized in the development and certification of aircraft, is a systematic and comprehensive evaluation process to determine that all relevant failure conditions have been identified and that all significant combinations of failures cannot result in unacceptable hazards. As the aircraft systems become more complex and require integrated function and performance, proper safety objectives must be established and appropriate assessments are need to be accompanied. This paper has prepared to propose the efficient probabilistic analysis of failure data to evaluate the risk level over the entire aircraft lifecycle through the safety assessment and to review the considerations for aircraft certification and safety improvement.

• Journal of Aerospace System Engineering
• /
• v.16 no.4
• /
• pp.60-67
• /
• 2022

An Electro-Optical Tracking System (EOTS) is an electric optical system with EO/IR cameras, laser sensors, and an IMU. The EOTS calculates coordinates of targets, using attitude and acceleration measured by the IMU. In particular for an armed aircraft, the performance of the weapon system depends on how quickly and accurately it acquires the target coordinates. The IMU should be operated after alignment is complete, to meet the coordinate accuracy required by the weapon system so the initial stabilization time of the IMU should be reduced, by quickly measuring the attitude and acceleration. Alignment is the process of determining the initial attitude by resolving the attitude error of the IMU, and the IMU of mission equipment such as an airborne EOTS, uses velocity matching based on the velocity from GPS/INS for aircraft navigation. In this paper, a method is presented to improve the transfer alignment performance of the airborne EOTS, by maneuvering aircraft and the mission equipment. First, the performance factor of the alignment was identified, as a heading error through the velocity matching model and simulation results. Then acceleration maneuvers and attitude changes were necessary, to correct the error. As a result of flight tests applied to an EOTS on a OOO aircraft system, the transfer alignment performance was improved as the duration time was decreased, by more than five times when the aircraft accelerated by more than 0.2g and the EOTS was moving until 6.7deg/s.

• Journal of Advanced Navigation Technology
• /
• v.27 no.5
• /
• pp.495-501
• /
• 2023

P-3C/K aircraft for maritime patrols that Republic of Korea Navy is using, is equipped with a variety of sensors and communication devices. Collected data from the aircraft is managed as tactical information by flight operators and stored. When the flight mission is completed, this information is transferred to tactical support center on the ground and played back or used for follow-up work through a analysis tool. During a flight mission, there are tens of thousands of detection objects within an hour in KADIZ (Korea air defense identification zone). In contrast, in TSD (tactical situation display), which displays a map when using the analysis tool, all detected objects are expressed as symbols. The increase in display symbols has a significant impact on the TSD image updating and consequently interferes with the smooth operation of operators. In this paper, we propose applying multiple threads and multiple layers to improve the performance of existing TSD. And the performance improvement is proven through the execution results.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.25 no.3
• /
• pp.135-142
• /
• 2017

As PED(Personal Electronic Device) market has been rapidly grown, the demand on Lithium battery, which is most commonly used power source of PED, also has been increased. Dew to this trend, the amount of Lithium battery air transportation is also increasing. However, it should be treated very carefully because Lithium is one of very explosive metal. So ICAO, IATA and civil aviation agencies try to enhance the safety of Lithium battery air transportation by aircraft certification and operating regulations. To enhance in-flight safety, the aircraft for transporting Lithium battery should equip certified fire extinguishing system. But recent studies find that Halon, currently used extinguishing agent, is not effective on extinguishing Lithium battery fire. Besides, there is no certified Halon replacement for air use and no acceptable specific minimum performance standard(MPS) for Lithium battery fire. For this issue, a study on characteristics and establishing MPS of Lithium battery fire is needed for safe air transportation of Lithium battery.

• Aerospace Engineering and Technology
• /
• v.6 no.2
• /
• pp.8-13
• /
• 2007

Improvement of the maintenance of firefly is another important part of the electrical system design with the performance. Usually, the maintenance of electrical system for small aircraft is more difficult than the maintenance of engine. The firefly electrical system imports the concept of module for design. In concept of module, sub-module can re easily isolated each other. Therefore, the maintenance of sub-module is possible. In this paper, the design and production of firefly electrical system is described.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.686-690
• /
• 2004

This paper describes the performance improvement of transient response and the modeling of small aircraft onboard generator. As the characteristics of the stator coil which are a major parameters of transient response were improved, the characteristics of transient response could be increased, therefore, the improved generator can be satisfied with large and fast load changes. Established the control model of the generator, it could be possible to do the analysis of generator performance, and improve the operational stability of the generator system using the control model.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.16 no.3
• /
• pp.277-284
• /
• 2013

In this paper, the ventilating and heating system of T-103 trainer aircraft were investigated and redesigned to improve its poor performance. The ventilation system of the trainer was designed to increase the mass flow rate of fresh air by using air intake valves. The flow-in air through the air intake valve is supplied to the cabin by the ram effect of aircraft and the propeller. And the additional heating system was installed to improve the temperature of the cabin inside. The wasted heat from the exhaust gas of the engines was used as heat source of the additional heating system by installing an heat exchanger around the exhaust nozzle. The additional fresh air and the heated air enter the cabin via two ducts mounted under the instrument panel and behind the pedal in the cabin. The additional ventilating and heating system can be controlled by the first pilot and the secondary pilot individually using the control knob equipped separately. After mounting the additional ventilating and heating system, evaluations such as inspection of parts and component, ground run-up test, in-flight test, user test, etc. were conducted. The result of the tests was sufficient to meet the requirements of the manuals, and the pilots were satisfied with the additionally mounted systems.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.6
• /
• pp.611-615
• /
• 2015

Anti-aircraft gun system is used for low-level air defense system and has more than twin guns with high firing rate in order to maximize the capability of defense. Gun's vibration and bullet's variance has a critical effect on accuracy and hit probability of weapon system such as anti-aircraft gun system with high firing rate. Typical mechanism to reduce the amount of vibration and shock during gun-fire process is very important design factor. In this paper, the suspension characteristics of the vehicle are studied for the improvement of isolating performance of gun firing system with high firing rate. Gun fire test for the vehicle is conducted and computational models using Recurdyn and Adams are created based on test results. Through this study, results of computational analysis are compared with the real test results, which includes type, location and quantity of suspension and gun mechanism are selected for anti-aircraft gun. From the result of this study, we could make basic design and consider the proper component of the system such as suspension and gun spring.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.332-337
• /
• 2018

Aircraft searchlights are used in search or rescue missions when performing night missions, and provide infrared light to keep operations in concealment. During aircraft operation, the infrared ray transmission filter glass for generating infrared rays can break, resulting in problems such as loss of concealment ability and maintenance. In this paper, we describe the procedure for testing the operating conditions of the searchlight when the defect occurs and finding the cause of the defect. We also summarize various methods to improve the cause and process of making the improved filter prototype. In addition, we also describe the results of verifying the performance requirements of the searchlight. As a result of the test and verification, the damage of the filter was improved and the improved filter was applied to the aircraft.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.13 no.1
• /
• pp.1-11
• /
• 2021

Performance of a NACA 63₄-021 hydrofoil in motion under and in close proximity of a free surface for a large range of angles of attack is studied. Lift and drag coefficients of the hydrofoil at different submergence depths are investigated both numerically and experimentally, for 0° ≤ AoA ≤ 30° at a Reynolds number of 10⁵. The results of the numerical study are in good agreement with the experimental results. The agreement confirms the new finding that for a submerged hydrofoil operating at high angles of attack close to a free surface, the interaction between the hydrofoil-motion induced waves on the free surface and the hydrofoil results in mitigation of the flow separation characteristics on the suction side of the foil and delay in stall, and improvement in hydrofoil performance. In comparing with a baseline case, results suggest a 55% increase in maximum lift coefficient and 90% average improvement in performance for, based on the lift-to-drag ratio, but it is also observed significant decrease of lift-to-drag ratio at lower angles of attack. Flow details obtained from combined finite volume and volume of fluid numerical methods provide insight into the underlying enhancement mechanism, involving interaction between the hydrofoil and the free surface.