• 대한토목학회논문집
• /
• 제39권4호
• /
• pp.523-530
• /
• 2019

포트홀 발생 및 관련 교통사고 건수는 매년 꾸준히 증가하는 추세이며 이에 따른 인명피해, 차량파손에 따른 비용손실 등 도로 이용자의 직 간접적인 피해를 증가시키고 있다. 일반적으로 아스팔트 혼합물은 생산과정부터 시공 후 공용에 따라 지속적으로 노화가 진행된다. 포장 노화는 균열과 수분침투로 박리를 야기하고 반복적인 윤하중에 의해 포장구조를 약화시켜 포트홀을 유발하게 된다. 본 연구에서는 노화가 아스팔트 콘크리트 포장에 미치는 영향을 검토하기 위해 노화정도에 따른 부착성능 평가와 수분민감성 평가를 수행하였다. 연구결과 노화에 따라 아스팔트 바인더의 점성이 증가해 부착강도가 2~3배 이상 증가하였다. 또한 가속 노화시킨 아스팔트 혼합물의 경우 간접인장강도의 증가뿐만 아니라 TSR 값도 4.2~8.9 % 증가하는 것으로 나타났다. 이에 따라 골재에 아스팔트 바인더가 피복된 상태에서 노화가 진행될 경우 아스팔트 바인더와 골재의 부착력이 증가하여 박리 저항성이 향상되는 것으로 분석되었다.

• Journal of Welding and Joining
• /
• 제4권2호
• /
• pp.21-29
• /
• 1986

The influence of welding heat input variation(600-900J/cm) and heat-treatment condition after welding on tensile strength of butt welded joint in $175Kg/mm^2$ strength level Maraging steel(Co-free and Co-containing) sheets was investigated on the basis of hardness distribution, microstructure of weld metal and fracture surface. The obtained main results are as follows; 1. The strength of weldment (UTS, NTS), joint efficiency showed a little decreasing tendency with the increase in welding heat input, and the elongation showed a little increasing tendency with the increase in the width of weld metal. It was considered because of the plastic constraint of the high strength base metal. 2. The strength of weldment was better in the solution treatment and aging than the aging only after welding due to the disappearance of almost denverite in weld metal. 3. The hardness distribution in weldment after welding and heat-treatment was almost similar to both Co containing and Co free Maraging steel with change in welding heat input. 4. The fracture was occurred at weld metal, and the fracture surface showed a relatively shallow dimples in both Co containing and Co free Maraging steel.

• 한국압력기기공학회 논문집
• /
• 제20권1호
• /
• pp.66-74
• /
• 2024

This study investigates the effects of temperatures and strain rates on the strength and ductility of Gr.91 (ASME Grade 91) steel which is widely being used as a heat-resistant material in Generation IV nuclear and super critical thermal power plants. The tensile behavior of modified 9Cr-1Mo (Gr.91) steel was studied for the three strain rates of 6.67×10^-5/s, 6.67×10^-4/s and 6.67×10-3/s over the temperature range from room temperature (RT) to 650℃. Experimental results showed that at specific combinations of temperatures (300~400℃) and strain rates, serrations appeared in the stress-strain curves. Concurrently, abnormal behaviors such as a plateau in yield strength and tensile strength, a minimum in ductility and negative strain rate sensitivity were observed. These phenomena were analyzed as significant characteristics of dynamic strain aging (DSA). Since this abnormal behavior in Gr.91 steel affects the material strength, it is judged that a correlation analysis between DSA and material strength should be crucial in the design and integrity evaluation of Gr. 91 steel pressure vessel and piping subjected to high-temperature loading.

• 전기학회논문지
• /
• 제65권9호
• /
• pp.1518-1523
• /
• 2016

In this study, in order to understand the degradation characteristics of oil-paper insulation for power transformers and OF cables, tan delta was measured using cable model specimens with long-term accelerated thermal and electrical aging. In addition, to find out the degradation level due to the accelerated aging, tensile strengths of aged papers were measured. As a result, tan ${\delta}$ showed the characteristics of slight decrease at the first stage and then increase with the aging time, which could be analyzed due to the evaporation of remaining moisture and the change of aging rate with time. Also, the trend of tensile strengths with aging temperature and time was appeared to be exponentially decreased and by use of these data equivalent calculated lifetimes and accelerated aging factors were derived for each aging temperatures. After then, tan ${\delta}$ was analyzed with the equivalent operating years. For all different aging temperatures, the aged data were very well fit to the equivalent operating years and it is shown that tan ${\delta}$ was increased with the decrease of tensile strength.

• 열처리공학회지
• /
• 제4권1호
• /
• pp.30-36
• /
• 1991

Effects of aging treatment on the mechanical properties of a 18 Ni maraging steel were investigated by considering the reverted austenite. Specimens were heat treated by austenitizing at $840^{\circ}C$ for 1 hr and then aged for various times at $480^{\circ}C$ and $520^{\circ}C$. The main results obtained are as follows : 1) The amounts of reverted austenite are increased up to about 4% at $480^{\circ}C$ and about 22% at $520^{\circ}C$ with 1 to 48 hrs aging time. 2) Decreasing tendencies of impact energy and fracture toughness with increasing aging time are diminished after aging for 2 hrs at two aging temperatures of $480^{\circ}C$ and $520^{\circ}C$. 3) Peak hardness and yield strength are obtained after aging for 4 hrs at $480^{\circ}C$ and 2 hrs at $520^{\circ}C$ respectively. From the above results, it was concluded that the optimum aging condition with which showed good strength and toughness combination are given to be $480^{\circ}C$ for 4 hrs and $520^{\circ}C$ for 2 hrs.

• 펄프종이기술
• /
• 제41권1호
• /
• pp.37-43
• /
• 2009

In this study, the physical properties of base paper for the manufacture of mulching mat for afforestation seedling were investigated. The base paper for mulching mat was prepared by stock conditions of PAE and AKD addition into the screened slurry of KOCC for the strengthening effects of wet tensile and burst strength. The optimum additions of PAE and AKD were considered at 2% and 0.5%, respectively. The accelerated aging by ISO 5630-1 and wet heat aging method under hot water for 2 kinds of commercial mulching and wet strength paper were compared with the base paper prepared for mulching mat manufacture. The accelerated aging test for the base paper prepared for mulching mat manufacture resulted in the same tendency of physical properties as two kinds of commercial products. However, the results of wet heat aging test under hot water indicated that the physical strength for base paper prepared was much higher than others. In addition, the opacity behavior for base paper prepared was enough effects to obstruct weeds growth by isolating transmission of sunlight.

• Journal of Welding and Joining
• /
• 제21권7호
• /
• pp.59-64
• /
• 2003

Microstructure and shear strength of Sn-Zn lead-free solders and Au/Ni/Cu UBM joint under thermal aging conditions was investigated. The samples were aged isothermally at 10$0^{\circ}C$ and 15$0^{\circ}C$ for 300, 600, and 900 hours. The IMCs(Intermetallic Compound) at the interface between solder and UBM were examined by FESEM and TEM. The results showed that the shear strength was decreased with aging time and temperature. The solder ball with high activated RA flux had about 8.2% higher shear strength than that of RMA flux. Poor wetting and many voids were observed in the fractured solder joint with of RMA flux. The decreased shear strengths were caused by IMC growth and Zn grain coarsening. Zn reacted with Au and then was transformed to the $\beta$ -AuZn compound. Although AuZn grew first, $r-Ni_5Zn_{21}$ compounds were formed with aging time. The layers indicated by $Ni_5Zn_{21}(1)$, (2), and (3) were formed with the thickness of ∼0.7 ${\mu}{\textrm}{m}$, ∼4 ${\mu}{\textrm}{m}$, and ∼2 ${\mu}{\textrm}{m}$, respectively.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.445-450
• /
• 2001

The paper investigates the relationships between dynamic elastic modulus and static elastic modulus or compressive strength according to curing temperature, aging, and cement type. Based on this investigation, the new model equations are proposed. Impact echo method estimates the resonant frequency of specimens and uniaxial compression test measures the static elastic modulus and compressive strength. Type I and V cement concretes, which have the water-cement ratios of 0.40 and 0.50, are cured under the isothermal curing temperature of 10, 23, and 50 $^{\circ}C$. Cement type and aging have no large influence on the relationship between dynamic and static elastic modulus, but the ratio of dynamic and static elastic modulus comes close to 1 as temperature increases. Initial chord elastic modulus, which is calculated at lower strain level of stress-strain curve, has the similar value to dynamic elastic modulus. The relationship between dynamic elastic modulus and compressive strength has the same tendency as the relationship between dynamic and static elastic modulus. The proposed relationship equations between dynamic elastic modulus and static elastic modulus or compressive strength properly estimates the variation of relationships according to cement type, temperature, and aging.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
• /
• pp.931-934
• /
• 2008

폴리우레탄은 방수재로 널리 사용되며 구조물에 발생되는 균열 및 거동에 의해 항상 외력을 받고있을 뿐만 아니라 사용 환경에 따라 각종 환경열화 인자에 노출되어 있다. 환경 열화인자로서는 자외선, 오존, 열, 수분 등이 잘 알려져 있다. 그 중에서 모든 열화의 기본이 되는 열의 영향, 특히 고온에서의 영향이 중요하다. 따라서, 노출형인 우레탄 고무계 1류 도막 방수재의 경우는 80$^{\circ}C$에서, 비노출형의 경우는 70$^{\circ}$C에서 촉진 열열화 시험을 3주간 실시하였다. 결과는 방수재의 기본물성과 인장 강도 및 신장율 모두 저하되는 경향을 보였으며, 특히 온도 60$^{\circ}$C에서 측정할 경우 급격히 물성 저하가 발생되었다.

• 한국분말재료학회지
• /
• 제19권4호
• /
• pp.317-321
• /
• 2012

In this study, Cu-5Ni-10Sn(wt%) spinodal alloy was manufactured by gas atomization spray forming, and the microstructural features and mechanical properties of Cu-5Ni-10Sn alloy have been investigated during homogenization, cold working and age-hardening. The spray formed Cu-5Ni-10Sn alloy consisted of an equiaxed microstructure with a mixture of solid solution ${\alpha}$-(CuNiSn) grains and lamellar-structure grains. Homogenization at $800^{\circ}C$ and subsequent rapid quenching formed a uniform solid solution ${\alpha}$-(CuNiSn) phase. Direct aging at $350^{\circ}C$ from the homogenized Cu-5Ni-10Sn alloy promoted the precipitation of finely distributed ${\gamma}$' or ${\gamma}-(Cu,Ni)_3Sn$ phase throughout the matrix, resulting in a significant increase in microhardness and tensile strength. Cold working prior to aging was effective in strengthening Cu-5Ni-10Sn alloy, which gave rise to a maximum tensile strength of 1165 MPa. Subsequent aging treatment slightly reduced the tensile strength to 1000-1100 MPa due to annealing effects.