• Korean Chemical Engineering Research
• /
• v.54 no.1
• /
• pp.114-119
• /
• 2016

In this study, we tried to add the conductivity to natural polymer like bacterial cellulose (BC) coated with the conductive polymer PEDOT:PEG, graphene and silver nano-wire (AgNW). Sulfuric acid of 10 to 20% was previously mixed with PEDOT:PEG and then the solution was electron spin-coated on the BC membrane. And then, additive coating with graphene and AgNW were done to improve conductivity, which was examined by hall effect. As the result, we confirmed a considerable improvement of conductivity compared to BC-coated film without sulfuric acid treatment as $2.487{\times}10^{10}$ vs $8.093{\times}10^{15}$ ($1/cm^3$), showing higher electron density with $3.25{\times}10^5$ times. Also, we identified that changed particle type to the polymer type by sulfuric acid using SEM analysis. For FT-IR analysis, it was confirmed that S-O radical ($1200cm^{-1}$) increased in the sulfuric acid treatment than non-treated sulfuric acid. As the method used very small amount of PEDOT:PEG, its transparency could be kept, and pre-treatment process of sulfuric acid will be able to simplify the production process.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.9
• /
• pp.572-576
• /
• 2017

A hybrid transparent electrode was fabricated with graphene and silver nanowires (Ag NWs). Three different processes were used to fabricate the hybrid electrode. Measurements of the sheet resistances, transmittances, and surface roughnesses of the hybrid electrodes were used to identify the optimal fabrication process. The surface roughness of the hybrid electrodes with Ag NWs embedded in a transparent polymer matrix was significantly lower than that of the other hybrid electrodes. A hybrid electrode fabricated by transferring graphene onto Ag NWs after spin-coating the Ag NWs onto the substrate showed the lowest sheet resistance. The transmittance of the hybrid electrodes was comparable to that of Ag NW electrodes.

• Journal of Surface Science and Engineering
• /
• v.50 no.6
• /
• pp.486-491
• /
• 2017

Silver nanowire (AgNW) transparent electrode is one of next generations of flexible and transparent electrode. The electrode shows high conductivity and high transparency comparable to ITO. However, the electrode is weak against heat. The wires are separated into nanodots at temperature above $200^{\circ}C$. It causes the electrical resistance increase. Moreover, it is vulnerable to oxygen and moisture in the atmosphere. The improvement of thermal and moisture resistance of silver nanowire transparent electrode is the most important for commercializing. We proposed silver nanowires transparent electrode which is capped with very thin nickel oxide layer. The nickel oxide layer is five nanometers of thickness, but the heat and moisture resistance of the transparent electrode is effectively improved. The AgNW/NiO electrode can endure at $300^{\circ}C$ of temperature for 30 minutes, and resistance is not increased for 180 hours at $85^{\circ}C$ of temperature and 85% of relative humidity. We showed an applications of transparent and flexible heater using the electrode, the heater is operated more than $180^{\circ}C$ of temperature.

• Journal of the Microelectronics and Packaging Society
• /
• v.23 no.3
• /
• pp.21-29
• /
• 2016

In this paper, we developed a flexible transparent capacitive pressure sensor which can recognize X and Y coordinates and the size of force simultaneously by sensing a change in electrical capacitance. The flexible transparent capacitive pressure sensor was composed of 3 layers which were top electrode, pressure sensing layer, and bottom electrode. Silver nanowire(Ag NW)/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS) hybrid film was used for top and bottom flexible transparent electrode. The fabricated capacitive pressure sensor had a total size of 5 inch, and was composed of 11 driving line and 19 sensing line channels. The electrical, optical properties of the Ag NW/PEDOT:PSS and capacitive pressure sensor were investigated respectively. The mechanical flexibility was also investigated by bending tests. Ag NW/PEDOT:PSS exhibited the sheet resistance of $44.1{\Omega}/square$, transmittance of 91.1%, and haze of 1.35%. Notably, the Ag NW/PEDOT:PSS hybrid electrode had a constant resistance change within a bending radius of 3 mm. The bending fatigue tests showed that the Ag NW/PEDOT:PSS could withstand 200,000 bending cycles which indicated the superior flexibility and durability of the hybrid electrode. The flexible transparent capacitive pressure sensor showed the transmittance of 84.1%, and haze of 3.56%. When the capacitive pressure sensor was pressed with the multiple 2 mm-diameter tips, it can well detect the force depending on the applied pressure. This indicated that the capacitive pressure sensor is a promising scheme for next generation flexible transparent touch screens which can provide multi-tasking capabilities through simultaneous multi-touch and multi-force sensing.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.26.1-26.1
• /
• 2011

We investigated the atomic layer deposition (ALD) process for nitrogen doped ZnO and the application for n-ZnO : N/p-Si (NW) coaxial hetero-junction photodetectors. ALD ZnO:N was deposited using diethylzinc (DEZ) and diluted $NH_4OH$ at $150^{\circ}C$ of substrate temperature. About 100~300 nm diameter and 5 um length of Si nanowires array were prepared using electroless etching technique in 0.108 g of $AgNO_3$ melted 20 ml HF liquid at $75^{\circ}C$. TEM images showed ZnO were deposited on densely packed SiNW structure achieving extraordinary conformality. When UV (360 nm) light was illuminated on n-ZnO:N/p-SiNW, I-V curve showed about three times larger photocurrent generation than film structure at 10 V reverse bias. Especially, at 660 nm wave length, the coaxial structure has 90.8% of external quantum efficiency (EQE) and 0.573 A/W of responsivity.

• Journal of the Semiconductor & Display Technology
• /
• v.20 no.2
• /
• pp.73-76
• /
• 2021

This thesis described the optical and electrical properties of the alternating current powder electroluminescent device based on Ag nanowire as a transparent electrode. The Ag nanowire electrode showed the morphology of 20 nm in diameter and 15 ㎛ in length. The transparent electroluminescent devices that were fabricated using the nanomilled ZnS : Cu, Mn phosphor by bar-coating process showed the transmittance of 67%. In order to improve the luminous efficiency, it is necessary to apply the transparent dielectric layer and increase the amount of the nanophosphor while maintaining the transmittance.

• Journal of the Mineralogical Society of Korea
• /
• v.32 no.2
• /
• pp.87-102
• /
• 2019

Pallancata Ag mine is located at the Ayacucho region 520 km southeast of Lima. The geology of mine area consists of mainly Cenozoic volcanic-intrusive rocks, which are composed of tuff, andesitic lava, andesitic tuff, pyroclastic flow, volcano clasts, rhyolite and quartz monzonite. This mine have about 100 quartz veins in tuff filling regional faults orienting NW, NE and EW directions. The Ag grades in quartz veins are from 40 to 1,000 g/t. Quartz veins vary from 0.1 m to 25 m in thickness and extend to about 3,000 m in strike length. Quartz veins show following textures including zonation, cavity, massive, breccia, crustiform, colloform and comb textures. Wallrock alteration features including silicification, sericitization, pyritization, chloritization and argillitization are obvious. The quartz veins contain calcite, chalcedony, adularia, fluorite, rutile, zircon, apatite, Fe oxide, REE mineral, Cr oxide, Al-Si-O mineral, pyrite, sphalerite, chalcopyrite, galena, electrum, proustite-pyrargyrite, pearceite-polybasite and acanthite. The temperature and sulfur fugacity ($f_{s2}$) of the Ag mineralization estimated from the mineral assemblages and mineral compositions are ranging from 118 to $222^{\circ}C$ and from $10^{-20.8}$ to $10^{-13.2}atm$, respectively. The relatively low temperature and sulfur-oxygen fugacities in the hydrothermal fluids during the Ag mineralization in Pallancata might be due to cooling and/or boiling of Ag-bearing fluids by mixing of meteoric water in the relatively shallow hydrothermal environment. The hydrothermal condition may be corresponding to an intermediate sulfidation epithermal mineralization.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.3
• /
• pp.37-41
• /
• 2019

Sheet resistance reduction in the Ag nanowire (NW) coated films is accomplished with slight improvement of optical properties for the application of transparent conducting electrodes by using $O_2$ plasma treatment. The sheet resistance was optimized after 30 seconds $O_2$ plasma treatment, showing the 27 % of maximum decrease of sheet resistance. It is found that the $O_2$ plasma treatment get rid of the residual organic materials at the junction of Ag NWs. However, the Ag NWs may be also snapped by the excessive $O_2$ plasma treatment can showing the collapses of Ag NWs networks. Furthermore, the optical properties such as optical transmittance and haze were monotonically improved with the $O_2$ plasma treatment time until 90 seconds.

• Economic and Environmental Geology
• /
• v.13 no.3
• /
• pp.167-184
• /
• 1980

The granitic plutons associated with Ogcheon geosynclinal zone can be grouped into three different subzones; SE-Subzone for the migmatitic and schistose granites of the southeast margin, 101-181m.y. old; NW-Subzone for those of the northwest margin, 112-163m. y. old; and C-Subzone for those of central part of the zone, 63-183m.y. old. The intrusives in C-Subzone are further subdivided into the older, adamellite to granodiorite (148-183m.y. old) and the younger, perthitic granites (63-106m,y. old). The metallogenic distribution of South Korea suggests that, in the Ogcheon Zone, it is possible to delineate an elongated polymetallogenic province in the general orientation of the zone intimately related with the migmatite and plutonic zones mentioned. Moreover, the mineralization in the province was basically controlled by the patterns of local geology involving country rocks and related igneous bodies, that permit subdivision of the province into the following three parts: Northeast (NE) Province consists dominantly of thick Paleozoic calcareous sediments; Middle (M) Province is characterized by predominant argillaceous and partly calcareous sediments of Precambrian to Late Paleozoic age; and Southwest (SW) Province consisting mainly of volcanic and arenaceous sediments of Mesozoic age. The three different plutonic zones with three different country rock provinces above mentioned make a combination which consists of nine classes. Each class can be assumed to be characterized by specific mineralization type. In order to classify the mineralization types, the present study sampled twenty six ore deposits and mineralized areas in Ogcheon zone as shown figure 2; eight ore deposits from plutonic SE-Subzone, ten from the plutonic NE-Subzone and eight from the plutonic C-Subzone. The characteristics of the classes are as follows: NE-SE is predominant in Au-Ag vein and Sn-migmatite of katazonal occurrence; NE-C is most productive in Pb-Zn and remarkable in Fe contact deposit in mesozone and partly Pb-Zn-Cu skarn in limestone and subordinate in mesozone and partly Pb-Zn pipes; M-SE is considerable in Au-Ag vein and rare elements (Nb, Ta, etc.) of pegmatite; M-C is predominant in F-veins in epizone and Mo-W, Fe, Cu veins occur in replacement type; M-NW is productive in Fe metamorphic and skarn types, partly remarkable in Cu, Pb-Zn contact; SW-SE is barren in mineralization related to Jurassic igneous rocks; SW-C is predominant in alunite and pyrophyllite in tuffs; and SW-NW is scarece in Pb-Zn, Cu, As and Au-Ag veins.

• Korean Journal of Materials Research
• /
• v.25 no.3
• /
• pp.125-131
• /
• 2015

Fluorine-doped $SnO_2$ (FTO) thin film/Ag nanowire (NW) double layers were fabricated by means of spin coating and ultrasonic spray pyrolysis. To investigate the optimum thickness of the FTO thin films when used as protection layer for Ag NWs, the deposition time of the ultrasonic spray pyrolysis process was varied at 0, 1, 3, 5, or 10 min. The structural, chemical, morphological, electrical, and optical properties of the double layers were examined using X-ray diffraction, X-ray photoelectron spectroscopy, field-emission scanning electron microscopy, transmission electron microscopy, the Hall effect measurement system, and UV-Vis spectrophotometry. Although pure Ag NWs formed isolated droplet-shaped Ag particles at an annealing temperature of $300^{\circ}C$, Ag NWs covered by FTO thin films maintained their high-aspect-ratio morphology. As the deposition time of the FTO thin films increased, the electrical and optical properties of the double layers degraded gradually. Therefore, the double layer fabricated with FTO thin films deposited for 1 min exhibited superb sheet resistance (${\sim}14.9{\Omega}/{\Box}$), high optical transmittance (~88.6 %), the best FOM (${\sim}19.9{\times}10^{-3}{\Omega}^{-1}$), and excellent thermal stability at an annealing temperature of $300^{\circ}C$ owing to the good morphology maintenance of the Ag NWs covered by FTO thin films.