• Design & Manufacturing
• /
• v.6 no.1
• /
• pp.95-100
• /
• 2012

In this study, a novel Cu composite sheet with embedded high electric conduction path was developed as another alternative for the interconnect materials possessing high electrical conductivity as well as high strength. The Cu composite sheet was fabricated by forming Ag conduction paths not within the interior but on the surface of a high strength Cu substrate by damascene electroplating process. As a result, the electrical conductivity increased by 40% thanks to mesh type Ag conduction paths, while the ultimate tensile strength decreased by 20%. The interfacial fracture resistance of Cu composite sheet prepared by damascene electroplating increased by above 50 times compared to Cu composite sheet by conventional electroplating. For feasibility test for practical application, a leadframe for LED module was manufactured by a progressive blanking and piercing processes, and the blanked surface profile was evaluated as a function of the volume fraction of Ag conduction paths. As Ag conduction path became finer, pressing formability improved.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.4
• /
• pp.50-58
• /
• 2000

Burning rate of the matrix propellant($r_{sb}$) and burning rate along the metal wire($r_w$) were measured and analyzed for the HTPB/AP/Al propellant embedded with Ag wire($\phi$0.15mm) according to weight % of RDX(0~20%). Variation of burning rate increment ratio($r_w$/$r_{sb}$) and pressure exponent(n) was studied for the nitramine propellant having 10% RDX embedded with three kinds of metal(Ag, Cu, and Ni-Cr) of which diameter range is between 0.1~0.6mm. Maximum burning rate increment ratio of the nitramine propellant embedded with Ag wire($\phi$0.1mm) was 5.94 at $20^{\cire}C$, 1000 psia, 16.4% faster than that of HTPB/AP propellant, it is because that autoignition temperature of the nitramine propellant was higher than that of HTPB/AP propellant. Standard deviation of absolute ($r_{wc}$/$r_{we}$)/$r_{we}$ calculated by using new empiracal equation composed of four dimensionless groups, is 6.11% less than that calculated by using original empirical equation composed of three dimensionless group. The new empiracal equation is derived from Buckingham pi theorem using the parameters such as thermal diffusivity, melting temperature. wire diameter, propellant sample diameter, frame temperature, autoignition temperature and matrix burning rate which influence on $r_w$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.9
• /
• pp.572-576
• /
• 2017

A hybrid transparent electrode was fabricated with graphene and silver nanowires (Ag NWs). Three different processes were used to fabricate the hybrid electrode. Measurements of the sheet resistances, transmittances, and surface roughnesses of the hybrid electrodes were used to identify the optimal fabrication process. The surface roughness of the hybrid electrodes with Ag NWs embedded in a transparent polymer matrix was significantly lower than that of the other hybrid electrodes. A hybrid electrode fabricated by transferring graphene onto Ag NWs after spin-coating the Ag NWs onto the substrate showed the lowest sheet resistance. The transmittance of the hybrid electrodes was comparable to that of Ag NW electrodes.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.2
• /
• pp.100-102
• /
• 2014

$Ag(Ta,Nb)O_3$ materials have a perovskite structure with a low loss tangent. These materials have been widely researched for their applications as high-frequency, passive components. Also, $Ag(Ta,Nb)O_3$ materials have weak frequency dispersion with high dielectric permittivity which gives them enormous potential for use in electronic components, including the filters, and embedded capacitors. Therefore, our research will discuss the structural and electrical relaxation properties of $Ag(Ta_{0.8}Nb_{0.2})O_3$ ceramics for device applications. We will investigate using X-ray diffraction to understand their structural properties and will analyze voltage dependent leakage current and timedependent relaxation behavior to understand their material properties.

• Journal of Sensor Science and Technology
• /
• v.24 no.4
• /
• pp.219-223
• /
• 2015

Indium free consisting of three alternating layers GTO/Ag/GTO has been fabricated by radio-frequency (RF) sputtering for the applications as transparent conducting electrodes and the structural, electrical and optical properties of the gallium tin oxide (GTO) films were carefully studied. The gallium tin oxide thin films deposited at room temperature are found to have an amorphous structure. Hall Effect measurements show a strong influence on the conductivity type where it changed from n-type to p-type at $700^{\circ}C$. GTO/Ag/GTO multilayer structured electrode with a few nm of Ag layer embedded is fabricated and show the optical transmittance of 86.48% in the visible range (${\lambda}$ = 380~770 nm) and quite low electrical resistivity of ${\sim}10^{-5}{\Omega}cm$. The resultant power conversion efficiency of 2.60% of the multilayer based OPV (GAG) is lower than that of the reference commercial ITO. GTO/Ag/GTO multilayer is a promising transparent conducting electrode material due to its low resistivity, high transmittance, low temperature deposition and low cost components.

• Progress in Superconductivity and Cryogenics
• /
• v.6 no.1
• /
• pp.1-5
• /
• 2004

Long length of Bi-2223/Ag superconducting wives were fabricated by stacking and drawing process with advanced heat-treatment schedules. Intermediate annealing was carried out to increase the homogeneity and uniformity of the superconducting filaments embedded in the silver matrix. Phase modification from tetragonal to orthorhombic Bi-2212 by pre heat treatment(PHT) was executed to improve the texture and phase transformation of Bi-2223. Drawing stress was measured to predict the sausaging and stress limit. Rolling Parameters such as thickness. width and winding tension were investigated to roll the tape with uniformity. 1 km length of Bi-2223/Ag superconducting wires were fabricated without any breakage. Critical current (Je) of 270 m length of superconducting tapes was measured over than $70 A/cm^2$ continuously after final sintering.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.10a
• /
• pp.63-66
• /
• 2003

1 km length of Bi-2223/Ag superconducting wires were fabricated by stacking, drawing process with advanced heat-treatment schedules. Intermediate annealing was carried out to increase the homogeneity and uniformity of the superconducting filaments embedded in the silver matrix. Phase modification from tetragonal to orthorhombic Bi-2212 by pre heat treatment(PHT) was executed to improve the texture and phase transformation of Bi-2223. Drawing stress was measured to Predict the sausaging and stress limit, Rolling parameters such as thickness, width and winding tension were investigated to roll the tape with uniformity. Critical current of 1 km length of superconducting tapes was measured about 50 A continuously after final sintering.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.532-535
• /
• 2000

We have fabricated a sensor system for on-line monitoring the oxygen permeability and diffusivity of six different polymer films using the miniaturized 6 cathode(Ag)-single anode(Ag/AgCl) type hexagonal oxygen electrode. This system consists of multiple input front-end electronics, signal conditioning circuit using the embedded microcontroller 80C196KC, PC interface circuit and PC with the OS for microcontroller and the operating program for this system. The digital low-[ass filter was programmed and the simulated filter characteristics were enough to eliminate the noise from sensor signal. According to the experimental results, the linearity coefficients of the output voltage to oxygen partial pressure for each sensor electrode of six cathode type oxygen sensor are 0.998, 0.997, 0.998, 0.997, 0.997, 0.997 respectively, and the response times are all within 4 minutes.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.40-41
• /
• 2011

본 연구에서는 기존 기판에 배선 형성 방법과 비교하여 매우 간단한 방법으로 배선을 기판 안에 함몰시키는 방법을 개발하였다. Gravure Offset Printing 방법으로 제작한 4 ${\mu}m$ 높이의 Ag 배선을 함몰하여 100 nm 로 만듬으로써 95% 이상이 기판 내부로 함몰되었음을 확인할 수 있었고, 함몰 전후의 면저항 값이 변화되지 않음을 확인할 수 있었다. 본 제작한 배선 함몰형 유연 기판은 각종 회로에 적용할 수 있고, 그 뿐만이 아니라 투명전극에 대한 보조 전극으로 적용 가능성을 확인할 수 있었다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.8
• /
• pp.483-485
• /
• 2014

Transparent amorphous In-Si-O (ISO)/Ag/In-Si-O (ISO) has been reported for low emissivity (low-e) applications. Effective Si doping into the $In_2O_3$ matrix led to a completely amorphous ISO film as well as a low resistivity and a high optical transmittance. The optical and electrical performances were examined by measuring transmittance with a UV-VIS spectrophotometer and resistivity with a Hall effect measurement. Consequently, low-e glass with ISO/Ag/ISO showed a high transparency in the visible region and low emissivity in the infrared region, indicating that ISO is a promising amorphous transparent electrode for low-e glass.