• Journal of Conservation Science
• /
• v.34 no.5
• /
• pp.397-405
• /
• 2018

Currently, there are very few studies on Korean wall paintings. Therefore, this study discusses the current conditions of wooden paintings and the characteristics of the adhesive agent in the painting layer separation. Korean land pine was chosen as the support, while white oysters shells, orpiment, red ocher, Noerok, and azurite were used as pigments. With four adhesive agents, including animal glue, Gelidium, methyl cellulose, and PVAc (caparol binder), a comparative experiment was conducted, by dividing them into two concentrations, of 0.5% and 1.5%. The temperature, humidity, and ultraviolet rays, which are contributing environmental factors in cultural assets after fixing, were artificially investigated. After deterioration, observed color difference, fixing, and the surface. Results showed that the animal glue strongly fixing all the colored layers compared to the other adhesives; however, azurite had a partial change when used outdoors. With Gelidium, which functioned similar to animal glue, the azurite was affected by the ultraviolet rays; nevertheless, despite the variations in temperature and humidity, it had the best gripping force compared to the other adhesive agents. Methyl cellulose was glossy at a high concentration, and was relatively strong against rapid changes in temperature and humidity. PVAc significantly reduced the binding force, compared to other adhesive agents.

• Journal of Adhesion and Interface
• /
• v.22 no.2
• /
• pp.31-38
• /
• 2021

In this study, a nonionic reactive emulsifier with aromatic and acryl group was synthesized by using polyoxyethylene(10) dodecylphenyl ether with 3-butenoic acid. The synthesized nonionic reactive emulsifier was confirmed by ¹H-NMR and FT-IR. In addition, the reactive emulsifier synthesized in the preparation of aqueous acrylic adhesives base emulsion was used and the properties of the solid content, conversion, particle size distribution, peel strength and high temperature holding force were compared to those of nonionic emulsifiers without aromatic group. The particle size was distributed from 370 nm to 698 nm, and the peel strength were measured in the range of 1.507~1.802 kg_f. The high temperature holding force of prepared adhesives base emulsion were measured in the range of 0.50~2.00 mm. Especially, in the result of synthesized nonionic reactive emulsifier with aromatic group, it was confirmed that high temperature holding force results were the most excellent than the case of using other nonionic reactive emulsifiers, and it can be useful for water-based acryl pressure sensitive adhesive.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.4
• /
• pp.354-361
• /
• 2008

Cold rolled steel sheet for automotive was treated by Ar/$O_2$ atmospheric pressure plasma to improve the adhesive bonding strength. Through the contact angle test and calculation of surface free energy for cold rolled steel sheet, the changes of surface properties were investigated before and after plasma treatment. The contact angle was decreased and surface free energy was increased after plasma treatment. And the change of surface roughness and morphology were observed by AFM(Atomic Force Microscope). The surface roughness of steel sheet was slightly changed. Based on Taguchi method, single lap shear test was performed to investigate the effect of experimental parameter such as plasma power, treatment time and flow rate of $O_2$ gas. Results shows that the bonding strength of steel sheet treated in Ar/$O_2$ atmospheric pressure plasma was improved about 20% compared with untreated sheet.

• Journal of Pharmaceutical Investigation
• /
• v.27 no.2
• /
• pp.133-137
• /
• 1997

Buccal absorption test of omeprazole in human was performed to determine the permeability of the drug molecule through oral mucous membrane. Oral mucosal adhesive tablets of omeprazole were prepared by compressing the omeprazole with a mixture of sodium alginate and hydroxypropylmethyl cellulose (HPMC) as bioadhesive polymers, magnesium oxide (MgO) as a stabilizer and sodium carboxymethyl cellulose (Na CMC) or cros-carmellose sodium (Ac-Di-Sol) as disintegrants. The bioadhesive force, stability in saliva and release characteristics of the tablets were evaluated. Omeprazole was absorbed about 23% in 15 min through human buccal mucous membrane. Furthermore, omeprazole was stable in saliva for more than 8 hrs when MgO was added to the tablet as the amount of 2.5 fold of omeprazole. The release rate of omeprazole was increased with increasing the amount of sodium alginate in the tablet. From these results, it is suggested that tablets composed of [omeprazole/HPMC/sodium alginate/MgO/Ac-Di-Sol and/or Na CMC (20/6/24/50/10) (mg/tablet)] are potential candidate for buccal drug delivery system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.6
• /
• pp.1092-1099
• /
• 2006

Displayed system equationally using accurate dynamic modeling of whole system including induction motor and load to analyze induction motor to normal condiction's action characteristic as well as transient characteristic using power converter device such as inverter in this paper. Also, presume adhesive power calculation through speed sensorless vector control and load torque disturbance observer for maximum tractive force control. Confirmed proposed algorithm through simulation and an experiment using railroad experiment equipment to embody control algorithm of such system. With relation of adhesive power about the wage speed by speed addition and subtraction of railway vehicle, embodied all sorts item by experiment equipment.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.5
• /
• pp.189-195
• /
• 2003

Atomic Force Microscope (AFM) has been widely used in micro/nano-scale studies and applications for. the last few decade. In this work, wear characteristics of silicon-based AFM tip was investigated. AFM tip shape was observed using a high resolution SEM and the wear coefficient was approximately calculated based on Archard's wear equation. It was shown that the wear coefficient of silicon and silicon nitride were in the range of ${10}^{-1}$~${10}^{-3}$ and ${10}^{-3}$~${10}^{-4}$, respectively. Also, the effect of relative humidity and sliding distance on adhesion-induced tip wear was discussed. It was found that the tip wear has more severe for harder test materials. Finally, the probable wear mechanism was analyzed from the adhesive and abrasive interaction point of view.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.346-346
• /
• 2006

Several types of dynamic atomic force microscopy such as tapping-mode, force modulation-mode are commonly cooperated by phase-contrast imaging techniques, which were interpreted as elastic contrast by mistake in the past and are nowadays regarded as the representation of energy dissipative processes. However, as theoretically reported, the situation is not so simple when the strong adhesive interaction is involved. Furthermore, elastic and viscous contributions are not easily divided in the case of polymeric systems. Thus, the interpretation of image contrast for them must be very carefully treated. In this study, we will demonstrate how such contrast mechanisms are complicated, using several miscible and immiscible polymer blend systems as model samples.

• International Journal of Safety
• /
• v.5 no.1
• /
• pp.10-16
• /
• 2006

A suspended hemispherical silicon asperity moving over a silicon plate was simulated. The simulation results on friction and wear in the interface between the two can help obtain more durable miscroscale structures. Silicon structures were constructed with Tersoff three-body potential. Dependence of friction and wear of the asperity on both the atomic arrangement in the plate and the moving direction was investigated under the condition that the asperity is subject to the attractive normal force due to the plate. The results show that the variation of friction force with the movement of asperity, and the occurrence of adhesive wear are attributed to the formation and rupture of asperity, junction between the asperity and the plate. The friction force and wear are smaller when the asperity is incommensurate with the plate, and they also depend on the moving direction of the asperity over the plate.

• Proceedings of the KIEE Conference
• /
• 1988.11a
• /
• pp.179-182
• /
• 1988

This study is to investigate the adhesive strength of composite material's interface on the experimental methode of tree growth in the material. The results are as fellows 1) The irradiations of ultrasonic energy cause the mechanical vibration in the polymer composite materials of fluid state, so then bring about physical dispersion and heat form inorganic materials, being supposed to produce chemical crosslinking reaction, decreasing of voids between filler and matrix. 2) The characterics of the breakdown are increased by using coupling agent in the composite material. 3) As the intensity of ultrasonic energy and its irradiated time are larger, the tree inception and break-down voltages increase and the tree growing is slower. so we obtain that the interface adhesive force tan be strengthened by the irradiation of ultrasonic energy.

• Proceedings of the KSR Conference
• /
• 2005.05a
• /
• pp.813-818
• /
• 2005

In this paper, a re-adhesion control scheme is proposed for 1C2M propulsion system of TTX. The possibility of slip between wheel and rail in railway system is increasing because of the tendency of high speed and a climatic change. This slip results in the decrease of adhesive effort between this wheel and rail, so the control strategy of traction effort which can reduce the speed promptly and make most use of the maximum adhesive force is absolutely necessary. This paper describes the modeling of the TTX system, and this system is verified by the simulation.