• 한국가스학회지
• /
• 제25권6호
• /
• pp.106-110
• /
• 2021

수소관련 신기술 및 신사업의 등장으로 액화수소 제조(충전), 액화수소 저장탱크 및 용기 제조 등 관련 분야에 대한 제도 정비 필요성이 확대되었고, 이를 실증하기 위한 규제특례(규제자유특구 및 규제샌드박스)제도가 도입됨에 따라 특례 신청이 지속적으로 증가하는 추세에 있다. 이에, 수소 관련 규제특례사업 지정현황을 파악하고 최소한의 안전성을 확보하기 위한 안전 관리 강화 방안을 수립하여 시행하고자 한다.

• 한국가스학회지
• /
• 제27권2호
• /
• pp.57-64
• /
• 2023

가스계량기의 검침방식이 발전하면서 원격검침이 가능한 스마트 가스 계량기(누출점검용 계량기 및 다기능 안전 계량기)가 사용되고 있다. 이러한 계량기는 부가기능으로 수집하는 유량 및 압력 데이터를 활용하여 누출 판단을 하는 기능이 있다. 유량 데이터를 이용한 누출판단 기능은 실제 현장에서 유효한 사례가 있지만 압력 데이터 기반 누출 판단 기준은 누출로 인한 압력 값 변화뿐만 아니라 여러 요인(정압기 압력 크기, 인접 계량기 연계, 인접 주택 사용량, 계량기 위치 등)으로 압력 크기 변화(레벨)가 있는 문제점이 있다. 본 논문에서는 스마트 가스계량기에서 수집되는 압력데이터를 활용하여 누출여부를 판단 할 수 있는 기법으로 압력 데이터 전처리 방법과 누출 여부 관련 압력 값 범위 기준, 누출판단 기법 및 적용 사례 검증을 통해 개발하였다.

• 한국정밀공학회지
• /
• 제26권8호
• /
• pp.112-118
• /
• 2009

A pressure rise is generated while air bearing stages are moving in high vacuum environment. This study analyzed this pressure rise phenomenon theoretically and verified it experimentally using two different kinds of stages - linear and rotary air bearing stages. Results indicate that the pressure rise was caused by additional leakage resulting from stage velocity, along with adsorption and outgassing of gas molecules from the guide rail surface. Though tilting of the stage due to acceleration and deceleration reached several micrometers, it had a negligible effect on pressure rise because the tilting time was very short. Therefore, a rotary air bearing stage showed much less pressure rise than a linear stage because the rotary stage theoretically has nothing to do with the above causes. Additional leakage caused by stage velocity was inevitable if the stage had movements, but pressure rise caused by adsorption and outgassing could be suppressed by improving the surface quality to reduce real surface area, and by coating the guide rail surface with titanium nitride (TiN) which has less adhesion probability of gas molecules. The results also indicate that the pressure rise increased when the air bearing stage operated under high vacuum conditions.

• 센서학회지
• /
• 제23권3호
• /
• pp.170-172
• /
• 2014

$CO_2$ sensor was used only one solid electrolyte in many cases. To improve the sensing characteristics of $CO_2$ sensors, solid electrolyte $CO_2$ sensor has been developed by bi-electrolyte type sensor using Na-Beta-alumina and YSZ. However, in many further studies, bi-electrolyte type sensor was made by pellet pressed by press machine and additional treatment for formation of interface. In the aspect of mass production, using thick film and additional treatment is not suitable. In this study, $CO_2$ sensor was fabricated by bi-electrolyte structure which was made by an NBA paste layer deposited on YSZ pellet and fired at $1650^{\circ}C$ for 2 hour. The formation of stable interface between YSZ and NBA were confirmed by SEM image. When the type IV electrochemical cell arrangement represented by $CO_2,O_2,Pt{\mid}Li_2CO_3-CaCO_3{\parallel}NBA{\parallel}YSZ{\mid}O_2,Pt$ is used to measure the $CO_2$ concentration in air. This sensor EMF should depend only on the concentration of $CO_2$ by logarithmic. Also, sensor shows $P_{CO_2}$ and EMF relationship like nerstian reaction at a temperature of $450^{\circ}C$.

• Design & Manufacturing
• /
• 제12권1호
• /
• pp.18-25
• /
• 2018

Both injection and injection molding dies have evolved into advanced technology. Product quality is also evolving day after day. Therefore, the conditions of the injection mold and the injection conditions are becoming important. In order to improve the quality of the product, the Hardware part of the mold has developed as an advanced technology, and the Software part has also developed with advanced technology. This study deals with the cooling part, which is part of the hardware. In addition to fluid cooling, which is commonly used in the industry, by using gas cooling identify the phenomena that appear on the surface of the product and the critical point strain of the product to find the optimal cooling. Electronic parts and automobile parts whose surface condition is important, the cooling process is important to such a degree that they are divided with good products and defective products according to the cooling process at the time of injection. By controlling this important cooling and reducing the injection time with additional cooling, the product quality can be increased to the highest production efficiency. In addition, high efficiency can be achieved without additional investment costs. This study was conducted to apply these various advantages in the field.

• Journal of Korean Society for Atmospheric Environment
• /
• 제19권E1호
• /
• pp.21-28
• /
• 2003

An auxiliary device, called Post Cyclone (PoC). had been introduced and primarily examined in earlier works which proved the reduction of the emission of fine dust from the gas-solid cyclones without incurring significant increase of cost and pressure drop. It has been known that the PoC has some advantages over other secondary dust treatment devices such as (a) simple design, (b) low cost of manufacture, (c) minimum additional pressure drop, (d) high recoverbility of the product dust, and (e) simplicity of operation. Despite the potential advantage, however, lack of practical data confined its plausible application in wide areas. Thus, in this work, a few serial experiments were conducted in terms of a few operation conditions, and the particle trajectories throughout the cyclone set-up were visually analyzed by using a commercial computer simulation program (FLUENT).

• International Journal of Automotive Technology
• /
• 제7권4호
• /
• pp.385-390
• /
• 2006

A fast response $CO_2$ analyzer has been developed to study transient characteristics on an SI engine. The analyzer has the delay time of 4.5 ms and time constant of 2.8 ms, which is fast enough to measure $CO_2$ concentration on a transient condition. Wide range of A/F(Air/Fuel) ratio can be estimated using the analyzer with an additional switch type oxygen sensor. The results of measurement of $CO_2$ concentration and A/F ratio on a transient condition including rapid acceleration/deceleration and EGR(Ehxaust Gas Recirculation) on/off are presented and compared with a commercial exhaust gas analyzer and UEGO(Universial Exhaust Gas Oxyzen) sensor.

• 한국표면공학회지
• /
• 제46권3호
• /
• pp.133-138
• /
• 2013

We have developed a 2D axi-symmetric numerical model for an inductively coupled plasma system in order to analyze gas mixing effect through a narrow gap shower head. For frictional flow, holes of 0.5 mm diameter and 2 mm length are approximately modeled in 2D. Gas velocity distribution 10 mm below the shower head showed 2 times difference between the center and the edge at 10 mTorr. At 10 mm above the wafer, it was increased to 6 times difference due to the pumping duct effect. The model with a 5 mm height buffer region of a shower head showed reasonable behavior of Ar discharge. The density of Ar metastable showed additional peak inside the buffer region around the edge holes.

• Nuclear Engineering and Technology
• /
• 제28권4호
• /
• pp.423-430
• /
• 1996

The improved and advanced Annulus Gas System(AGS) has been developed for Wolsong 2 to satisfy the requirements of the regulatory body. The Atomic Energy Control Board(AECB) required a shorter detection time following a small leak from a pressure tube and/or calandria tube. This paper describes licensing requirements, functional requirements and detail design description for the AGS. The Wolsong unit No. 1 AGS was designed to operate as a stagnant system normally requiring only pressure regulation and having provisions for purging. no improved AGS involves the adoption of gas recirculation in AGS, duplication of dew point indicators with additional instrumentation and sampling provisions to prompt operator action. The improved system operates in the recirculation mode with continuous dew point measurement for leak detection. An AGS with improved detection instrumentation is provided.

• 한국가스학회지
• /
• 제18권1호
• /
• pp.1-7
• /
• 2014

본 연구에서는 LPG자동차용 LPG 액상분사 인젝터의 분사구 앞에 장착할 수 있는 플라즈마 개질기의 개발을 진행하였다. 이 개질기는 플라즈마 방전이 발생하는 영역에 공기와 LPG 연료를 분사시켜 고분자 탄소연료를 열해리시키고 추가로 수소를 발생시키기 위한 목적으로 개발되었다. 인젝터와 플라즈마 발생부와의 거리와 기하학적인 방전길을 최적화하여 개질 반응이 일어나는 인젝터 개질기를 완성하였으며, 개질 결과 공급 전력 70~100W 일 때 HC은 전체 개질가스의 약 0.7% 이며, 수소는 1.2~1.5% 발생하였다.