• Journal of the Korean Wood Science and Technology
• /
• v.41 no.1
• /
• pp.12-18
• /
• 2013

Existing wood decks brings out negligent accident because fastener can be pulled-out by cyclic load of pedestrians. When deck and joist are connected, it also causes the problems, which are cracking of wood decks and rapid decay by material of fastener. In this study, strength property of deck unit using reinforced plastic connector made by domestic A company was evaluated. Southern yellow pine (Pinus palustris Miller) were used for deck material. Bending strength of deck units were implemented for fastener type and joist spacing (400, 600 mm). In the result, carbon steel screw into reinforced plastic connector was the best in average bending strength(Joist spacing : 400, 600 mm). In the result of bending strength for joist-width (40, 50, 70, 80 mm), the average maximum bending strength was measured when the joist spacing was 40 mm.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.5
• /
• pp.497-503
• /
• 2018

Passenger ships and training ships have a common feature in that they serve many passengers. Thus, safe navigation is very important. During normal sailing, a ship may turn using various types of steering, including maneuvers to avoid collisions with dangerous target. When a ship turns, a heeling angle occurs. If trouble arises during sailing, a dangerous heeling angle may result or a capsizing accident. In this study, the heeling angle during turning was measured through experimentation with two training ships similar to passenger ships. These findings were compared with theoretical formulas for heeling angle when turning. We confirmed that the limit of the maximum heeling angle estimation using heeling angle formula when turning presented in IMO stability criteria. In addition, it was confirmed that the maximum estimated heeling angle can be reached by applying the result calculated in the theoretical formula 1.4 times when turning right and 1.1 times when turning left to reflect sailing speed when of rudder hard over. It is expected that this study will provide basis data for establishing safe operation standards for the prevention of dangerous heeling angles when turning.

• Korean Journal of Construction Engineering and Management
• /
• v.12 no.5
• /
• pp.71-80
• /
• 2011

Flying net should be installed on every 3 or 4 construction floor from 8m above ground according to the rule. In the apartment housing construction, flying net installation work has been recognized the most dangerous work among the whole works because a small mistake of labors might make their death accident. Sub-contractors specialized in flying net have been developing various flying net types. However, most works of installing flying net as working with the developed system are performed outside the apartment housing, so that the risk of fall in works of installing supports and unfolding net is still high. Furthermore, as using the previously developed flying net labors might bump into the frame or the wire rope for supporting so that it makes secondary accidents. The objective of this research is to produce the proto-type of anti-collision flying net system based on the result of problem analysis on the installation and detachment process and suggest the improved anti-collision flying net system, which is able to improve safety and field applicability by conducting field experiment and analyzing performance.

• Journal of Preventive Medicine and Public Health
• /
• v.24 no.3 s.35
• /
• pp.279-286
• /
• 1991

Much of the working population in developing countries are engaged in shift work now and the number of shift workers is not expected to decrease in the future mostly because the need for continuity of production is increasing. Therefore, the possible effects of shift work on health are of particular interest, and in fact, there have been many epidemiological studies on shift work since the first world war. However, no studies on health effects of shift work have been reported in Korea, and the existing studies in western world have arrived at quite different conclusions mainly because the conditions of work other than shift work, such as age and selection of workers, work environment, and labor conditions also influence the health of workers. This study was firstly carried out in Korea to investigate the health risks related to shift work with 2,093 female workers randomly selected from three major manufacturing industries in proportion to total number of female workers in those industries. Differences of work conditions other than shift work in this study were adjusted by multivariate analysis. Ma findings obtained from this study are as follows : 1. There were significant differences between shift and day workers in the distribution of age, type of industry, condition of noise and dust, regularity of mealtime, working position, and working duration. Shift workers tended to be younger, to have shorter working duration, to have more irregular mealtime, to work in standing position, and to work under more noisy and dusty environment than day workers. 2. Univariate analysis showed that shift work increased the Todai Health Index (THI) scores of digestive tract, respiratory tract, and mental instability symptom categories. Shift work also increased days of sickness absence and number of industrial accident per 100 workers per month. 3. Multivariate analysis that adjusted the differences of demographic, occupational and non-occupational health-related working conditions showed that digestive tract symptom and mental instability symptom scores were significantly higher in shift workers than those in day workers. Based on these study results, it is concluded that the shift work has significant effects on some psychophysiological conditions of the workers and the effects are also influenced by several other personal and working conditions.

• Journal of Digital Convergence
• /
• v.15 no.8
• /
• pp.391-400
• /
• 2017

The purpose of this paper is to present the effect of image stimulation on body stability as a conceptual model and to investigate the effect of image stimulus(2D, VR) on body stability(hand stability) through experiments Recently, stereoscopic images such as virtual and augmented reality are combined with smart phones and exercise equipments, and the diffusion is becoming active. The possibility of a safety accident or human error is also increasing as it temporarily affects the balance of the body and hand stability after the image stimulus is removed. The conceptual model is presented based on the results of previous studies. Based on the experimental results, the conceptual model has been explained in combination with the human information processing process and cognitive resource models that take place in the brain. Twenty subjects were exposed to 2D and VR stimuli, and display fatigue was measured by cybersickness questionnaire and hand stability by hand steadiness tester. Experimental results show that VR images induce higher display fatigue and lower hand stability than 2D. In this study, it is meaningful that hand stability according to image type and display fatigue level which have not been tried yet is revealed through conceptual model and experiment.

• Journal of Environmental Policy
• /
• v.13 no.4
• /
• pp.79-105
• /
• 2014

Natech risk is a type of complex disasters that natural hazards trigger technological disaster or industrial accidents. Research on Natech risk has been started from the mid-1990s in European countries and the Unites States, and drawn much more attention after the Fukushima nuclear accident caused by the 2011 East Japan earthquake. While early studies on Natech risk have focused on the causal natural hazards and possibility to occur, and the resulting spill of hazardous materials from the perspective of science and engineering, the recent research interests lie on effective Natech risk management. Especially, emphasizing the difference of Natech risk management from traditional disaster management, issues of uncertainty management, integration between natural disaster and technological disaster, and responsibility, has been drawn attention. In Korea, Natech risk has not been introduced as a research topic. Although some regulatory improvements have been made in nuclear safety and chemical Substance management after the Fukushima disaster, the potential impact of natural hazards in these areas has not been considered yet. It is necessary to raise the issues of Natech risk management in research and policy areas through active discussion and interdisciplinary approaches.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.9
• /
• pp.69-75
• /
• 2014

Rock fall protection system installed against rock slope is one of the most conventional way to protect nearby infra structures. Despite of wide application of typical rectangular nets, virtually installed to protect rock slope face, several problems have also been pointed out up to date. Rectangular draped nets are vulnerable to a sudden external shock such as rock fall, because it doesn't have any systematical buffers or shock absorbers. Furthermore, it has been widely recognized from the some cases of rock fall accident in Korea that rock fall protection nets cause wide range of failure in the rock slope faces due to insufficient pullout bearing capacity of fixing parts. Therefore, in this study, we tried to make a consideration about the problems of existing standard rock fall protection nets in Korea, and develop a new type of hexagonal net with a shock absorber based on design rock fall energy. In this paper, laboratory and full scale test procedure is described to analysis the performance of newly developed hexagonal rock fall net, and the key results are presented and discussed.

• Journal of Advanced Navigation Technology
• /
• v.16 no.2
• /
• pp.360-366
• /
• 2012

In the power distribution panel installed in airport or industrial facilities, MCCB has been used for main switch and ELCB for branch switch to perform human body and leakage-inducing fire protection as well as overcurrent and short circuit protection. Especially for the airport panel, increase in accident protection is needed for stable power supply due to rapid modernization with fast-growing users, higer capacity and diversification of equipment, the increase of power capacity and the breaker made slim is a main issue for now because the issue for installation space is standing out by making panel with two-row arrangement connection method, etc. due to a many use of branch ELCBs. In this thesis, we designed arc extinguishing mechanism, considered movement direction change of contact in mechanism design. Also, we designed the breaker to work stably in case of miniaturization of leakage detection circuit and reverse connection. We conducted short circuit test to verify its function and developed the breaker that can be improved protection against accidental current with slim size operating leakage function when reverse connection to help solve the problem in using space that is increasing in the airport distribution panel.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.44-52
• /
• 2019

Industrial accidents differ considerably according to the industry and the scale of these industries. These industrial disasters have been analyzed in various ways. Therefore, a technique was developed to evaluate the disaster level among companies using the ANP method and the data derived from the disaster statistics over the past five years(2013~2017), as well as the safety information characteristics through questionnaires. The objective of the study was to determine the disaster level and safety level of a company. In this paper, six factors that are considered important for assessing the disaster level of the enterprise among the disaster statistics were selected. These factors included the industry type and size, age of employee, duration of treatment, duration of employment, and typical occurrence. Most companies use the accident rate for their disaster level to compare only with other companies. In this study, the weighting factors of the company were derived taking the characteristics of each company into consideration. Therefore, the disaster level of each company can be evaluated using the disaster statistics from each company and the derived weighting factors.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.3
• /
• pp.32-38
• /
• 2020

This study examined the problems of existing vehicles to propose alternatives to improve the crashworthiness of railway freight cars through collision acceleration analysis using a one-dimensional collision analysis method. A collision scenario of railway shunting and crash accidents was selected from the collision accident cases and international standards. A one-dimensional collision simulation using LS-DYNA was performed according to those scenarios. As a result, the acceleration level of the freight wagon was calculated to be under 2g and was predicted to meet the EN 12663 standard in the shunting situation. On the other hand, the result of crash simulation with an impact velocity between 10 and 15 km/h revealed the shock absorber capacity of the railway coupler to be insufficient in a crash situation, resulting in increased acceleration, and carbody deformation could be predicted. As a method of improving the crashworthiness, a deformation tube-type energy absorber was applied to the coupler system, and collision analysis was performed again with new energy absorption strategy. Overall, the simulation showed that the acceleration level was decreased by 12% of the conventional freight-car energy absorption system.