• 대한기계학회논문집A
• /
• 제22권3호
• /
• pp.603-610
• /
• 1998

This paper develops a 7 DOF vehicle model to study the effects of the active suspension on ride. The model is used to derive a control law for the active suspension using a full state linear optimal control technique. A wheelbase preview type active suspension is also considered in the control law derivation. The time delay between wheelbases is approximated using Pade approximation technique. The ride model is extended to a 14 DOF handling model. The 14 DOF handling model includes lateral, longitudinal, yaw and four wheel spin motions in addition to the 7 DOF ride model. A control law which is derived considering only ride related parameters is used to study the effects of the active suspension on a vehicle handling. J-turn maneuver simulation results show that the active suspension has a slower response in lateral acceleration and yaw rate, a bigger steady state lateral acceleration and an oversteer tendency. Lane changing maneuver simulation results show that the active suspension has a little bigger lateral acceleration but a much smaller roll angle and roll motion. Braking maneuver simulation results show that the active suspension has a much smaller pitch angle and pitch motion.

• 항공우주시스템공학회지
• /
• 제13권6호
• /
• pp.43-51
• /
• 2019

택싱모드 상태에서 노면의 가진으로 발생하는 기체 가속도는 조종사와 탑승객의 탑승감을 해치는 주 요인이다. 본 논문에서는 MR댐퍼 착륙장치의 탑승감을 향상시키기 위해 제어기법을 연구하였다. 제안된 제어기법은 Skyhook Control Type2 로 기존의 스카이훅 제어와는 달리 추가적으로 상부질량가속도를 피드백 받아 제어력을 구성한다. Skyhook Control Type2는 상부질량의 속도와 가속도를 모두 고려하기 때문에 상부질량속도만을 고려하는 스카이훅 기법의 제어한계를 개선하는 효과가 있다. 시뮬레이션을 위해 범퍼형태의 노면을 활주노면으로 선정하였으며, 리커다인(RecurDyn)으로 구성한 착륙장치 모델과 시뮬링크(Simulink)로 설계한 제어기를 연동해석 하였다. 시뮬레이션을 통해, 상부질량가속도의 RMS값과 최대값을 활주속도 및 제어기법에 따라 비교 분석하여 Skyhook Control Type2에 대한 제어효과를 검증하였다.

• 반도체디스플레이기술학회지
• /
• 제12권1호
• /
• pp.53-59
• /
• 2013

Chip mounter which is used to pick chips from the pre-specified position and place them on the target location of PCB is an essential device in semiconductor and LCD industries. Quick and high precision positioning is the key technology needed to increase productivity of chip mounters. As increasing acceleration and deceleration of placing motion, structural vibration induced from inertial reactive force and flexibility of mounter structure becomes a serious problem degrading positioning accuracy. Motivated from these, this paper proposed a new control design algorithm which combines a mounter structure acceleration feedforward compensation and an extended sliding mode control for fine positioning and suppression of structural vibration, simultaneously. The feasibility of the proposed control design was verified along with some simulation results.

• 융합신호처리학회 학술대회논문집
• /
• 한국신호처리시스템학회 2006년도 하계 학술대회 논문집
• /
• pp.77-80
• /
• 2006

This paper based on spiral vector, three phase induction motor is described a detailed modeling by a phase segment methode. Based on this model, A torque control and the equation of regenerative power for the induction motor drive, based on the field acceleration method(FAM), is presented. The speed control system is designed to be applied voltage source inverters that is easy the current type feedback of power regeneration for motor drive. The ability of shaving power to be measured power regeneration has been investigated in speed acceleration and reduction. And it is change of stator resistance that the voltage commands include error, the ripple of exited voltage and torque occur from the results. The experimental tests verify the performance of the proposed regenerative drive for FAM, proving that good behavior of the drive is achieved in the transient and steady-state operating conditions.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 A
• /
• pp.391-394
• /
• 1993

The acceleration/deceleration control method and interpolated operating are essential to the servo motor control system. In a few years ago, a floating point DSP chip was used for the purpose of processing a lot of calculated amount. But in this paper, we proposed new acceleration/deceleration control method and circular interpolation algorithm without another floating point DSP chip. The validity of proposed algorithms are verified through computer simulation and experimental result.

• 대한임베디드공학회논문지
• /
• 제16권6호
• /
• pp.285-292
• /
• 2021

Autonomous vehicles are divided into an upper controller that calculates control value through cognitive judgment and a lower controller that appropriately transmits its control value to an actuator. Here, the longitudinal control in a lower controller has a problem as the road slopes due to the property of the Acceleration sensor to output the acceleration as the slope of the device. Therefore, in this paper, a sigmoid function is proposed to determine the slope to compensate for this problem. Through the experiment, Checked performance by comparing the existing table model with the proposed model.

• 한국정밀공학회지
• /
• 제23권3호
• /
• pp.110-117
• /
• 2006

This paper presents the acceleration optimization of a high-speed LCD (Liquid Crystal Display) transfer system for the minimization of vibration. To reduce vibration is one of key requirements for the dynamic control of a high-speed LCD transfer system. In this paper, the concept of finite jerk (the first derivative of acceleration) has been introduced for realizing input acceleration. The profile of finite jerk has been optimized using a genetic algorithm so that vibration effect can be minimized. In order to incorporate a genetic algorithm, the dynamic model of a LCD transfer system which is realized by using the ADAMS software has been linked to the simulation system constructed by the MATLAB. The simulation results illustrated that the duration of finite jerk can be optimized so as to minimize the magnitude of vibration. It has been also shown that the acceleration optimization with finite jerk can make the high-speed motion of a LCD transfer system result in low vibration, compared with the conventional motion control with trapezoidal velocity profile.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2002년도 ICCAS
• /
• pp.48.4-48
• /
• 2002

1) A method to realize active vibration control using SAC and acceleration type sensor is proposed from the viewpoint of practical application. 2) The use of acceleration type sensor makes it easy to satisfy ASPR condition in applying SAC system and to implement sensor in practical mechanical system. 3) Results were confirmed through numerical simulation of 1 DOF vibration system.

• 전력전자학회논문지
• /
• 제6권1호
• /
• pp.90-97
• /
• 2001

본 논문에서는 시스템의 광성 추정에 의한 가속도 전향보상 방법을 이용한 새로운 속도제어 기법을 제안한다. 제안된 가속도 전향보상 방법에 의해 속도제어기의 대역폭을 충분히 크게 할 수 없는 백터제어 유도전동기 구동시스템에서 속도제어 성능을 향상시킬 수 있고, 외란 토크에 대한 속도회복특성도 개선될 수 있다. 3.7kW 유도전동기 구동시스템에 대한 시뮬레이션과 실험을 통해 제안된 기법의 타당성을 확인하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.780-783
• /
• 2004

Recently Intake noise has been extensively studied to reduce the engine noise. In order to diminish intake noise several resonators were added to the intake system. However this can cause a reduction of engine output power and an increase of fuel consumption. In this study, active noise control simulation of the Filtered-x LMS algorithm is applied real instrumentation intake noise data under rapid acceleration because intake noise is more excessively increased under the such a harsh condition. But the FXLMS algorithm has poor control performance when the system is disturbed. Thus modified FXLMS algorithm using L-point running average filter is developed to improve the control performance under the rapid acceleration and disturbance. The noise reduction quantity of modified Filtered-x LMS algorithm is more than original one in two cases. In the case of control for real instrumentation intake noise data, maximum residual noise of modified FXLMS algorithm is 2.5 times less than applied the FXLMS and also in the case of disturbed, the modified FXLMS algorithm shows excellent control performance but FXLMS algorithm cat not control.