DOI QR코드

DOI QR Code

Study on the Taxing Mode Control of MR Damper Landing Gear

MR 댐퍼 착륙장치의 택싱모드 제어기법에 대한 연구

  • Lee, Hyosang (Dept. of Aerospace and Mechanical Engineering, Graduate at KAU) ;
  • Hwang, Jaihyuk (Dept of Aerospace and mechanical Engineering, Korea Aerospace University)
  • 이효상 (한국항공대학교 항공우주 및 기계공학과) ;
  • 황재혁 (한국항공대학교 항공우주 및 기계공학부)
  • Received : 2019.07.15
  • Accepted : 2019.11.20
  • Published : 2019.12.31

Abstract

The aircraft vertical acceleration from the excitation of the road surface in the taxing mode is a main factor with a negative effect on the boarding quality of pilots and passengers. In this paper, we propose an appropriate control method to improve the boarding quality of the MR damper landing gear. The proposed control method is Skyhook Control Type 2, which feeds the aircraft vertical acceleration back in addition to the aircraft vertical velocity. Since Skyhook Control Type 2 factors the velocity and acceleration of the upper mass, it can be expected to exceed the control performance of the existing Skyhook Control that factors only the upper mass velocity. For the simulation, the bumper type road surface was selected as a ground surface, and the landing gear model constructed with RecurDyn and the controller designed with Simulink were co-simulated. The control effect of Skyhook Control Type 2 was verified by comparing and analyzing the RMS and maximum value of the upper mass acceleration according to the taxing speed and control method.

택싱모드 상태에서 노면의 가진으로 발생하는 기체 가속도는 조종사와 탑승객의 탑승감을 해치는 주 요인이다. 본 논문에서는 MR댐퍼 착륙장치의 탑승감을 향상시키기 위해 제어기법을 연구하였다. 제안된 제어기법은 Skyhook Control Type2 로 기존의 스카이훅 제어와는 달리 추가적으로 상부질량가속도를 피드백 받아 제어력을 구성한다. Skyhook Control Type2는 상부질량의 속도와 가속도를 모두 고려하기 때문에 상부질량속도만을 고려하는 스카이훅 기법의 제어한계를 개선하는 효과가 있다. 시뮬레이션을 위해 범퍼형태의 노면을 활주노면으로 선정하였으며, 리커다인(RecurDyn)으로 구성한 착륙장치 모델과 시뮬링크(Simulink)로 설계한 제어기를 연동해석 하였다. 시뮬레이션을 통해, 상부질량가속도의 RMS값과 최대값을 활주속도 및 제어기법에 따라 비교 분석하여 Skyhook Control Type2에 대한 제어효과를 검증하였다.

Keywords

References

  1. Ji-Sang Park, Dynamic Analysis of Aircraft Landing Gear under Nonstationary Random Excitation Using Nonlinear Model, MS Thesis, Korea Aerospace University, Gyeong-gi, Republic of Korea, 1999.
  2. John R. McGehee and Huey D. Carden, "A mathematical model of an active control landing gear for load control during impact and roll - out", NASA Langley Research Center Hampton, Va. 23665, Rep. NASA TND -8080, February 1976.
  3. Han, Y. M., and Choi, S. B., "Semi-Active and Active Vibration Control Techniques," Noise and Vibration, Vol. 18, No. 3, pp. 16-24, 2008.
  4. Howell, W. E., McGehee, J. R., Daugherty, R. H., and Vogler, W. A., "F-106B Airplane Active Control Landing Gear Drop Test Performance," NASA TM 102741, 1990.
  5. Horta, L. G., Daugherty, R. H., and artinson, V. J., "Modeling and Validation of a Navy A6-Intruder Actively Controlled Landing Gear System," NASA TP 209124, 1999.
  6. J. M. Tak, L. Q. Viet, and J. H. Hwang, "Semi-Active Control of Aircraft Landing Gear using Magneto-rheological Damper," The Society for Aerospace System Engineering 2017 Fall Conference, pp. 225-227, November 2017.
  7. G.Yang, B.F.Spencer, Jr., J.D. Carlson and M.K. Sain, "Large-scale MR fluid dampers: modeling, and dynamic performance considerations", Engineering Structures, Vol. 24, pp. 309-323, 2002. https://doi.org/10.1016/S0141-0296(01)00097-9
  8. Milwitzky, B., and Cook, F., "Analysis of Landing Gear Behavior," NACA TN 2755, 1952.
  9. Karnopp, D., Crosby, M. J., and Harwood, R. A., "Vibration Control Using Semi-Active Force Generators," Journal of Engineering for Industry, Vol. 96, No. 2, pp. 619-626, 1974. https://doi.org/10.1115/1.3438373
  10. Sergio M. Savaresi, Enrico Silani, Sergio Bittanti, "Semi-Active Suspensions: An Optimal Control Strategy for a Quarter-Car model", IFAC Symposium on Advances in Automotive Control, Vol. 37 Issue 22, pp. 553-558, Salerno, Italy, 19-23 April 2004
  11. Kum-Gil Sung and Seung-Bok Choi, "Ride Comfort Evaluation of Electronic control Suspension Using a magneto-rheological Damper", The Korean Society for noise and Vibration Engineering, Vol. 23 No. 5, pp. 463-471, 2013. https://doi.org/10.5050/KSNVE.2013.23.5.463