• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.1
• /
• pp.64-75
• /
• 2013

As both laboratory accelerated experiment and field exposure experiment were performed, at recent, the fifth field test at five year exposures was proceeded according to long period experimental plan. Field experiment, for the adoption of the developed evaluation model, which is consisted of the analysis of chloride penetration profile at gate bridges of sea-dike completed 30 years ago was carried out during upgrading the basic evaluation model with analyzing the annual field test data. The surface concentration of chlorides was replaced to the concentration of chloride of inner concrete near the surface chlorides among his research results at basic model. Maage's suggestion function was accepted too as a diffusion coefficient of chloride after verifying the change of diffusion coefficient by analysis of annual field test data. The comparison of field data with model predictions and the estimation of remaining life time demonstrates that the proposed updated model and maintenance simulation system can be used to predict the chloride penetration profile in the marine tidal zone and appropriate repair period and cost.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.4A
• /
• pp.753-759
• /
• 2006

To predict service life of concrete structures exposed to chloride attack, surface chloride concentration, diffusion coefficient of chloride ion, and chloride corrosion threshold value in concrete, are used as important factors. Of these, as the diffusion coefficient of chloride ion for concrete is strongly influenced by concrete quality and environmental conditions of structures and may significantly change the service life of structures, it is considered as the most important factor for service life prediction. The qualitative factors affecting the penetration and diffusion of chloride ion into concrete are water-cement (W/C) ratio, age, curing conditions, chloride ion concentration of given environment, wet and dry conditions, etc. In this paper the influence of W/C ratio and curing conditions on the diffusion characteristics of chloride ion in concrete was investigated through the chloride ion diffusion test. In the test, the voltages passing through the diffusion cell were measured by accelerated test method using potential difference, and then with the consideration of IR drop ratio the diffusion coefficient of chloride ion for concrete with different W/C ratios were estimated by Andrade's model. Furthermore, under different curing conditions formulas for the estimation of the diffusion coefficient of chloride ion have been proposed by the regression analysis considering the effect of W/C ratio and age.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.219-219
• /
• 2009

ceramic metal halide lamps are a subset of high intensity discharge lamps so named because of their high radiance These lamps weak ionized plasma in a fire-resisting but light transmissive wrapping by the corridor of current through atomic and molecular vapors. for commercial applications, For commercial applications, the conversion of electric power to light must occur with good efficiency and with sufficient spectral content throughout the visible (380-800 nm) to permit the light so generated to render colors comparable to natural sunlight. the purpose of this paper is to carry out a study on the variation of ageing time(2000 On/Off[hr]) on the performance of 150W CMH lamps. Experimental results show that the blackening by reacting W(tungsten)with I atomic has been created in the arc tube of an ageing lamp(2000 On/Off[hr]), the arc was unstable, and increased a lamp resistance made lamp voltage increases significantly. Also, Color temperature of the ageing lamp was moved by the losses of Ho with Dy atomics and by recombination of Na with I.

• Architectural research
• /
• v.7 no.1
• /
• pp.49-54
• /
• 2005

Conventional studies have focused on the reduction in the water-cement ratio, the use of various admixtures, etc., to ensure the durability of reinforced concrete structures against such deterioration factors as carbonation and chloride attack. However, improvement in the concrete quality alone is not considered sufficient or realistic for meeting the recent demand for a service life of over 100 years. This study intends to improve the durability of reinforced concrete structures by improvement in the reinforcing steel, which has remained untouched due to cost problems, through subtle adjustment of the steel components to keep the cost low. As a fundamental study on the performance of Cr-bearing rebars in steel reinforced concrete structures exposed to corrosive environments, The test specimens were made by installing 8 types of rebars in concretes with a chloride ion content of 0.3, 0.6, 1.2, 2.4 and $24kg/m^3$. Corrosion accelerated curing were then conducted with them. The corrosion resistance of Cr-bearing rebars was examined by measuring crack widths, half-cell potential, corrosion area and weight loss after 155 cycles of corrosion-accelerating curing. The results of the study showed that the corrosion resistance increased as the Cr content increased regardless of the content of chloride ions, and that the Cr-bearing rebars with a Cr content of 5% and 9% showed high corrosion resistance in concretes with a chloride ion content of 1.2 and $2.4kg/m^3$, respectively.

• Journal of Applied Reliability
• /
• v.5 no.2
• /
• pp.241-259
• /
• 2005

The environmental problem is a main subject of the 21C and an environment destruction phenomenon by various kinds of environmental materials is reaching serious level. Nations to be classified as the environmental developed country, are born again environmental rich country. And they earn a large income by trade Every kind environmental resource in an international commercial transaction. Especially, the study that a reliability assessment method to prevent to reliability problem to be happened when the solder lead(lead-free solder), non-cd component, non-bromide component(without the polybrominated biphenyls(PBB) and polybrominated diphenyl ethers(PBDE))and hexavalent chromium(Cr VI) clearance component and mercury-free applied to electronic equipment is progressed. As the result of the study for applying of a reliability assessment technique of lead-free solder that recognized the most of urgent problem at the company, combination accelerated life test could taken by adding and appling the part of a humidity acceleration part to Eyring Model which is proposed by R.E.Thomas. The reliability assessment methods study of PWB clean environmental materials is expected to respond to a reliability elevation and environmental material regulation policy spreading all over the world by beginning form Europe.

• International Journal of Highway Engineering
• /
• v.14 no.5
• /
• pp.21-29
• /
• 2012

PURPOSES: This study is to investigate the mechanical performance of the fiber reinforced lean concrete with respect to different types of fibers. METHODS: Increased vehicle weight and other causes from the exposed conditions have accelerated the deteriorations of road pavement. A new multi-functional composite pavement system is being developed recently in order to extend service life and upgrade the pavement. A variety of tests were conducted before and after hardening of the concrete. RESULTS: From the test results, it was found that the use of different types of fibers did not affect the compressive strength development. This might be due to the inherent property of the lean concrete. When steel fibers were used relatively greater flexural strength and flexural fracture toughness were developed. Also addition of fly ash by replacing a part of Portland cement the fracture toughness was slightly increased. CONCLUSIONS: It has been known that the addition of fibers and use of mineral admixture can be positively considered in the development of multi-functional composite pavement system as its required mechanical performance is obtained.

• Journal of Electrical Engineering and Technology
• /
• v.4 no.1
• /
• pp.123-130
• /
• 2009

The partial discharge (PD) measurement is a very effective method to assess the winding insulation condition of high-voltage machines, since most of the insulation failure processes are directly or indirectly caused by PD. On-line PD measurements, which can detect insulation defects of winding in the early stages on rotating machines in operation, have been accepted as the most important technique. The epoxy mica capacitive coupler is currently and extensively used for on-line detection of PD pulses of high-voltage rotating machines. To evaluate the feasibility of developing a capacitive coupler that is easier to manufacture at a lower cost compared to epoxy mica couplers, a 100pF capacitive coupler made of ceramic material is designed, fabricated and tested for on-line PD measurements of 23 kV electrical machines. A series of electrical tests and accelerated aging tests are performed on the ceramic coupler to evaluate the performance requirements, long-term reliability and thermal stability for in field application. The test results show that the newly developed ceramic coupler provides equal and improved performance at a lower cost compared to epoxy mica couplers, and estimated voltage life is anticipated to surpass 100 years.

• Proceedings of the Korean Reliability Society Conference
• /
• 2005.06a
• /
• pp.393-404
• /
• 2005

The environmental problem is a main subject of the 21C and an environment destruction phenomenon by various kinds of environmental materials is reaching serious level. Nations to be classified as the environmental developed country, are born again environmental rich country. And they earn a large income by trade Every kind environmental resource in an international commercial transaction. Especially, the study that a reliability assessment method to prevent to reliability problem to be happened when the solder lead(lead-free solder), non-cd component, non-bromide component(without the polybrominated biphenyls(PBB) and polybrominated diphenyl ethers(PBDE))and hexavalent chromium(Cr VI) clearance component and mercury-free applied to electronic equipment is progressed. As the result of the study for applying of a reliability assessment technique of lead-free solder that recognized the most of urgent problem at the company, combination accelerated life test could taken by adding and appling the part of a humidity acceleration part to Eyring Model which is proposed by R.E.Thomas. The reliability assessment methods study of PWB clean environmental materials is expected to respond to a reliability elevation and environmental material regulation policy spreading all over the world by beginning form Europe.

• Journal of Life Science
• /
• v.13 no.1
• /
• pp.9-14
• /
• 2003

Seed germinability might be highly related to seedling establishment. The experiments were carried out to evaluate the effect of presowing treatments of aging, priming, $GA_3$ , prechilling and water imbibition, different temperatures and light quality during germination on germination of gourd (Lagenaria siceraria Standl.) seeds. Aging treatment with different temperatures and periods was done by the accelerated aging method. Priming using KNO$_3$ and $GA_3$ treatment for 24 hours were done at 100 mM and at 0.01 mM before a week prechilling. The germination tests using a week prechilled seeds were done at 10, 20 and $30^{\circ}C$ on the condition of darkness, and also with blue, red, far-red light and darkness as light quality treatments. FR-yongjadaemok and FR-kunghap were used as test cultivars and their daily germination rates were measured at treatment levels. Germination rates were reduced in the seeds aged at $45^{\circ}C$ for 6 days. Prechilling showed the highest and fastest rate among the four presowing treatments but the two other presowing treatments had similar or less rates than water imbibition. Prechilling done before sowing enhanced the low vigor seeds, and accelerated the germination of cv. FR-kunghap at 20 to $30^{\circ}C$ and with blue, red light or darkness during germination although far-red light inhibited their germination.

• Journal of Life Science
• /
• v.19 no.10
• /
• pp.1389-1395
• /
• 2009

Generally, it takes a long time to purify wood vinegar, and it contains toxic compounds such as tar, methanol, phenol and benzopyrene. To reduce the toxicity of wood vinegar itself, we have developed a new purification method of wood vinegar using an oxidation-cohesion reaction and distillation with an active carbon. We have investigated the physico-chemical change (pH, specific gravity, refractive index and dissolved tar), the change of amount of toxic compounds (carbonyl group, phenol, benzopyrene and residual solvents) and organic acids (formic acid (FA), acetic acid (AA), propionic acid (PA)) of the purified wood vinegar under the long term and accelerated storage conditions. Also, we have evaluated the effect of the purified wood vinegar on hair growth using an alopecia model of C57BL/6 mice. As a result, we could find out that the purified wood vinegar was stable and remained without decay under the storage conditions and benzopyrene, a carcinogenic agent, was not detected in the purified wood vinegar. After topical treatment of the purified wood vinegar solution or minoxidil (MXD) for 2 weeks to dorsal skin, the hair regrowth of the mice accelerated faster than that of the control, with no clinical signs. In conclusion, we could suggest a guideline for quality control of process to reduce the toxic compounds in wood vinegar and it might be a useful hair growth promoter in the treatment of baldness or alopecia.