• Journal of Hydrogen and New Energy
• /
• v.28 no.6
• /
• pp.729-737
• /
• 2017

The measurement accuracy of Tunable Diode Laser Absorption Spectroscopy based Tomography (TDLAST) for the temperature and concentration fields are dependant upon the arrangement method of the used laser beams. This paper reports on the optimization of laser beam arrangements using phantom data. It has been verified that the measurement error of the TDLAST decreased with increase of laser beam numbers. Further, it has been confirmed that perpendicular arrangements between the horizontal and the vertical laser beams without additional diagonal laser beams shows the minimum measurement errors.

• Journal of the Korean Society of Visualization
• /
• v.21 no.1
• /
• pp.103-109
• /
• 2023

This research developed a measurement technique that can measure the oxygen temperature inside a high temperature furnace. Instead of measuring only changes in frequency components within a small range used in the existing variable laser absorption spectroscopy, laser spectroscopy technology was used to spread out wavelength of the light source passing through the gas Based on a total of 20,000 image data, research was conducted to predict the temperature of a high-temperature furnace using CNN with black and white images in the form of spectral bands by temperature of 25 to 800 degrees. The optimal model was found through Hyper parameter optimization, R2 score is 0.89, and the accuracy of the test data is 88.73%. Based on this research, it is expected that concentration measurement and air-fuel ratio control technology can be applied.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.11a
• /
• pp.197-198
• /
• 2022

Based on the carbonation depth measurement by the indicator for concrete collected from old structures and the quantitative analysis of Ca(OH)₂ and CO₂ in the carbonation section before and after the carbonation depth and in the non-carbonation section, the absorbable CO2 amount and carbonation degree measurement result is as follows 1) The carbonation depth of the 40-year-old reinforced concrete structure was measured to be about 22 mm. (basement interior wall, marble finish, strength 30MPa) 2) The amount of CO₂ absorbed by the concrete was about 4.3% of the sample weight, and the carbonation degree was estimated to be about 53%.

• Nuclear Engineering and Technology
• /
• v.56 no.8
• /
• pp.2906-2915
• /
• 2024

Radiocarbon (¹⁴C), with a radioactive half-life of approximately 5730 years, poses a long-term environmental contamination risk when released into the atmosphere. The quantification analysis of its release estimates plant-specific generation rates based on factors such as plant power, core neutron flux distribution, and the volume of water exposed to this flux. Utilizing the improved estimation method, the ¹⁴C production rate for several Korean Pressurized Water Reactors (PWRs) was calculated. Also, improvements in measurement methods through sampling have also been made. These enhancements include the verification of the absorption method versus the mixing method. The results of this study indicate that plant-specific ¹⁴C production rates range from 0.213 to 0.317 TBq/yr, which are comparable to the global range observed in PWRs. Furthermore, the study evaluated a quenching correction curve for a liquid scintillation counter using two quenching correction methods: the external standard method and the internal standard method. The accuracy of these methods with 72 samples was validated with an average relative error within ±2.5%. The relative error of the mixing method, when compared to the direct absorption method, was found to be within ±20%. This finding underscores the validity of the improved measurement technique.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.16 no.4
• /
• pp.263-267
• /
• 2013

In this research, a novel optical measuring methodology for the measurement of oil thickness in seawater is suggested by evaluating the light absorption which is occurred in the process of penetrating through oil layer on seawater. Laser having monochromatic wave is used as a light source and photodiode which can convert the intensity of the light into an electrical signal is applied to measure the intensity of the penetrating light through the oil-water mixtures. In the experiment, bunker C and lubricating oil are used, and three different lasers having different wavelengths are applied and compared for the selection of an optimal light source. As a result, it is observed that in the case of blue laser, the intensity of the light on the optical sensor decreases with an increase in the oil thickness. Through this relation, both the presence of oil and the thickness of oil can be determined.

• Macromolecular Research
• /
• v.12 no.6
• /
• pp.559-563
• /
• 2004

Both the ultrasonic velocity at 3 MHz and the absorption coefficient in the frequency range from 0.2 to 2 MHz were measured for aqueous solutions of poly(sodium 4-styrenesulfonate) over the concentration range from 5 to $25\%$ (by weight). The pulse echo overlap method was employed to measure the ultrasonic velocity over the temperature range from 10 to $90^{\circ}C;$ the high-Q ultrasonic resonator method was used for the measurement of the absorption coefficient at $20^{\circ}C.$ The velocities exhibited their maximum values at ca. 55, 59, 63, 67, and $71^{\circ}C.$ for the 25, 20, 15, 10, and $5\%$ solutions, respectively. The velocity increased with respect to the poly(sodium 4-styrene-sulfonate) concentration at a given temperature. A study of the concentration dependence of the both the relaxation frequency and amplitude indicated that the relaxation at ca. 200 kHz is related to structural fluctuations of the polymer molecules, such as the segmental motions of the polymer chains and that the relaxation at ca. 1 MHz resulted from the proton transfer reactions of the oxygen sites of $SO_3.$ Both the absorption and the shear viscosity increase upon increasing the polymer concentration, but they decrease upon increasing the temperature.

• Journal of Hydrogen and New Energy
• /
• v.18 no.3
• /
• pp.334-341
• /
• 2007

Al film(135.5 nm thick) with Pd film(39.6 nm thick) was made by thermal evaporation method. Electrical resistance change by hydrogen absorption and desorption was measured with four point measurement method. Even though Al film(135.5 nm thick) did not absorb any hydrogen at room temperature, Al/Pd film absorbed hydrogen at upto 640 torr pressure. Hydrogen absorption kinetics was monitored by measuring resistance change of the sample in the temperature range from $25^{\circ}C$ to $40^{\circ}C$. Absorption activation energy of Al/Pd film was about 10.7 and 17.7 kcal/mol H for 1st stage and last stage respectively at 1 torr hydrogen pressure. This activation values are bigger than that of Pd film, but are much less than that of Al film. This result indicates there is possibility that Al can be storage material for hydrogen by using Pd film evaporation on it.

• Coupled systems mechanics
• /
• v.6 no.3
• /
• pp.273-286
• /
• 2017

We present a simple and easy-to-implement lumped stiffness model to elucidate the load transfer mechanism among all individual tube shells and intertube van der Waals (vdW) interactions in transversely compressed multi-walled carbon nanotubes (CNTs). Our model essentially enables theoretical predictions to be made of the relevant transverse mechanical behaviors of multi-walled tubes based on the transverse stiffness properties of single-walled tubes. We demonstrate the validity and accuracy of our model and theoretical predictions through a quantitative study of the transverse deformability of double- and triple-walled CNTs by utilizing our recently reported nanomechanical measurement data. Using the lumped stiffness model, we further evaluate the contribution of each individual tube shell and intertube vdW interaction to the strain energy absorption in the whole tube. Our results show that the innermost tube shell absorbs more strain energy than any other individual tube shells and intertube vdW interactions. Nanotubes of smaller number of walls and outer diameters are found to possess higher strain energy absorption capacities on both a per-volume and a per-weight basis. The proposed model and findings on the load transfer and the energy absorption in multi-walled CNTs directly contribute to a better understanding of their structural and mechanical properties and applications, and are also useful to study the transverse mechanical properties of other one-dimensional tubular nanostructures (e.g., boron nitride nanotubes).

• The Korean Journal of Ceramics
• /
• v.6 no.4
• /
• pp.359-363
• /
• 2000

Reduced nicotinamide adenine dinucleotide (NADH) was encapsulated in transparent porous sol-gel silicate gels using by different organoalkoxysilane precursor. Characteristics optical absorption and fluorescence of NADH in the gels were examined with depending on NADH concentration and compared. Optical absorption in the aminopropyltrimethoxysilane (APTMS) gel is highest and remains constant during aging the gel. Thus, it is found that NADH in the APTMS gel is most stable and activated. On the other hand, methyltriethoxysilane (MTES) gel presents the lowest optical absorption diminishing with aging the gel. Measurable increase of fluorescence with raising the NADH concentration is observed except for the APTMS gel due to its solubility in the buffer during fluorescence measurement.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.5
• /
• pp.631-640
• /
• 2020

In this study, the effect of specimen size and layer thickness on the sound absorption of the leaves of two evergreen broad-leaved tree species, Dendropanax morbiferus and Fatsia japonica, was investigated. The specimen sizes of 0.5 × 0.5, 1.0 × 1.0, and 2.0 × 2.0 ㎠ and layer thicknesses of 1.00, 1.75, and 2.50 cm were considered. At the layer thickness of 2.5 cm, the leaf of the D. morbiferus showed no significant difference in sound absorption coefficients (SACs) as the sample size varied, however, a significant change in SACs was recorded in that of the F. japonica. At 1.0-cm thickness, the SACs of the F. japonica leaf varied more remarkably with the sample size. The 2.50-cm-thick F. japonica leaf with the specimen size 0.5 × 0.5 ㎠ exhibited the highest sound absorption effect among all samples investigated.