• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.1194-1197
• /
• 2006

Recently, international standard for measurement of sound absorption in a reverberation room has been amended. In the revised version, temperature, humidity and air pressure conditions are strictly restricted and also the concrete procedures are presented to reduce the differences in test results by adding inspection of diffusion, measurement uncertainty etc. In this paper, the systematic tests are conducted based on the inspection guide of diffusion defined by ISO 354 and the effects of diffusers on the measurement of sound absorption ratio are considered. As a result, we perceived that the averaged sound absorption ratio in mid and high frequency range is expected to measure around $0.05{\sim}0.1$ higher in high sound absorption material. Therefore, as for the reverberation room for measurement of sound absorption, we need to take into consideration not only the spatial standard deviation of sound pressure mandated by ISO 3741, but also, inspection regulation of diffusion showed by ISO 354.

• Journal of Electrical Engineering and information Science
• /
• v.3 no.1
• /
• pp.80-85
• /
• 1998

A theoretical calculation and an optical measurement method of normal-incidence absorption are proposed. By using a waveguide structure, optical interference and the problem of low level signal can be avoided in the measurement of normal-incidence absorption. The oscillator strength of intersubband absorption for a waveguide structure is calculated in Si(001), Si(110), and Ge(001) quantum wells. The polarization angle dependence of the measured and the calculated absorption strength can be obtained with the same waveguide structure, and be compared after normalization. The normal-incidence absorption in Si(110) and Ge(001) quantum wells is shown theoretically, and can be observed in the optical measurement using waveguide structures at the polarization angle of 90$^{\circ}$.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.12
• /
• pp.1317-1324
• /
• 2011

We propose a method operated in a vehicle to measure light absorption of particles in atmosphere. The advantage of this method is that it is insensitive to light scattering and hence can be used for the direct measurement of the light absorption coefficient without suffering from light scattering. With this method atmospheric light absorption can be measured at a time constant of 10 s. Further, our method allows for the real-time measurement of light absorption near a highway. The light absorption coefficients were high near a race track, an airport and the main gate where vehicles emitted carbonaceous particles.

• Journal of the Optical Society of Korea
• /
• v.5 no.4
• /
• pp.123-130
• /
• 2001

In this paper, we report measurement of absorption coefficient for various InGaAs MQW QCSE device structures. The absorption spectra over a range of QCSE were obtained from measured photocurrent spectra. The refractive index changes with applied electric field were calculated from the absorption spectra.

• Journal of ILASS-Korea
• /
• v.7 no.2
• /
• pp.1-6
• /
• 2002

It is necessary to develope a high frequency diode laser sensor system based on the absorption spectroscopy for the measurement of temperature of the spray flame. DFB diode laser operating near $2.0{\mu}m$ was used to scan over selected $H_2O$ transitions near $1.9{\mu}m\;and\;2.2{\mu}m$, respectively. The measurement sensitivity at wide range of sweep frequency was evaluated using multi-pass cell containing $CO_2$ gas. This diode laser absorption sensor with high temporal resolution up to 10kHz was applied to measure the gas temperature in the spray flame region of liquid-gas 2-phase counter flow flame. The successful demonstration of time series temperature measurement in the spray flame gives us motivation of trying to establish non-intrusive temperature measurement method in the practical spray flame.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.05a
• /
• pp.197-200
• /
• 2010

In some cases it is important to be able to measure not only the total sound intensity on a panel surface in a vehicle cabin, but also the components of that intensity due to sound radiation and due to absorption from the incident field. For example, these intensity components may be needed for calibration of energy flow models of the cabin noise. A robust method based on surface absorption coefficient measurement is presented in his paper.

• Bulletin of the Korean Chemical Society
• /
• v.13 no.5
• /
• pp.553-556
• /
• 1992

The ${CO}_2$ laser absorption measurement of ${CH}_3{CH}_2Br$ utilizing photoacoustic (PA) technique was performed using a cw and a pulsed ${CO}_2$ lasers. The absorption profile in the ${CO}_2$ laser wavelength region (9-10 ${\mu}$m) and the macroscopic small signal absorption cross section at 10P(20) (10.59 ${\mu}$m, 944 $cm^{-1}$) laser line were measured using a cw ${CO}_2$ laser. The laser fluence dependence on infrared multiphoton absorption (IRMPA) was also studied with a pulsed TEA ${CO}_2$ laser at 10P(20) laser line. In view of monotonic increase of PA signal with the rise of laser fluence, it was suggested that the anharmonicity in pumped vibration mode did not restrict ir multiphoton absorption in ${CH}_3{CH}_2Br$ system as found in large molecular system.

• Textile Coloration and Finishing
• /
• v.25 no.2
• /
• pp.89-93
• /
• 2013

The electrochemical study has been enjoyed in many areas of chemistry. Through this approach using electrochemical measurement, empirical HOMO and LUMO values can be calculated by three methods such as absorption measurement, cyclicvoltammetry and computational calculations. In this study, 1,3-bisdicyanovinylindane was prepared and investigated toward its optical properties. The absorption intensities were changed depending on changes of pH. These absorption changes are induced by resonance form of 1,3-bisdicyanovinylindane. The electron delocalization in ${\pi}$ system is related to the resonance form. In according to this electron density distribution and HOMO/LUMO values of 1,3-bisdicyanovinylindane were simulated and calculated by Material Studio 4.3, absorption measurement and cyclicvoltammograms. The 1,3-bisdicyanovinylindane is one of the most attracted acceptor units in D-${\pi}$-A system. This attempt is useful to determine more detailed characteristics of the energy potentials.

• The Journal of the Acoustical Society of Korea
• /
• v.40 no.3
• /
• pp.254-260
• /
• 2021

When measuring the sound absorption coefficient of a specimen, a reverberation room which is costly or an impedance tube which has limitations in measuring low frequencies have been engaged. In this paper, a new measurement method of acoustic impedance or sound absorption coefficient has been suggested, which does not need microphones and only uses electrical impedance measurement data and derived Thiele/Small parameters of a speaker. The theory of this method has been described using equivalent circuit of the loudspeaker and acoustic properties of a test specimen are measured to demonstrate the validity of this method. It was confirmed that this method can easily measure the sound absorption coefficient in the low frequency band, which was previously difficult to trust. The advantages, limitations, and applicability of this method are discussed.

• 한국연소학회:학술대회논문집
• /
• 2006.10a
• /
• pp.97-103
• /
• 2006

This work forcus on the development of gas sensor that measure the concentrations of exhaust gas using diode laser. Each diode laser for exhaust gas measurement is set to work at near-IR using both DA and WMS methods. Also use of fiber-coupled optical elements makes such a sensor rugged and easy to align. On-line data acquisition and processing can be performed with a PC running LabVIEW software, and absorption signals are measured simultaneously by multiplexing method. Finally, It were experimentally compared WMS (Wavelength Modulation Spectroscopy) with DA (Direct Absorption) for the accuracy.