• 한국의류학회지
• /
• 제40권3호
• /
• pp.495-505
• /
• 2016

This study explores and selects an appropriate material that considers light and soft physical properties as well as activity for impact absorption pads that can be used to develop practical impact protective clothes worn during daily life by the elderly to reduce the impact of falls. Physical properties, impact absorption performance, and compression characteristics were evaluated on 5 types of foam, 2 types of 3D spacer fabric, and 3 types of polymer gel to select a material appropriate for the pad to be inserted into impact protective clothes. The evaluation of the physical properties showed that 3D spacer fabrics had lower density compared to other materials and polymer gels had the highest density. The elongation percentage was higher in foams than 3D spacer fabrics and EPDM foam had the highest elongation percentage. The impact absorption performance of honeycomb polymer gel was better than foams and 3D spacer fabrics. As a result of looking into compression energy and compression characteristics of materials, 'CR foam A' was found to absorb the largest amount of compression energy, 24.1%, among foams and polymer gels. A high energy absorption rate of 50.0% (or above) was indicated by 3D spacer fabrics; however, foams and polymer gels showed a progressive deformation of energy compression / recovery curve with 3D spacer fabrics that showed drastic deformation. Based on characteristics of materials, 'CR foam C' and EPDM with relatively high absorption performance can be used as protective pad materials among foams. Among polymer gels, 2 open-type polymer gels that have relatively low impact protective performance but a relatively lighter weight on human body (compared to closed-type) are considered appropriate protective pad materials.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.156-156
• /
• 2008

Single crystal of $In_2S_3$ and $In_2S_3:Co^{2+}$ were grown successfully with a good quality by the CTR(Chemical Transport Reaction)method. XRD analysis showed that the grown In2S3 and $In_2S_3:Co^{2+}$ single crystals were cubic structure. The optical absorption spectra of $In_2S_3:Co^{2+}$ single crystal showed impurity absorption peaks due to cobalt impurity. These impurity absorption pesks were assigned to the ligand transition between the split energy levels of $Co^{2+}$ ions with $T_d$ symmetry of these semiconductor host lattice.

• 한국전기전자재료학회논문지
• /
• 제26권9호
• /
• pp.656-661
• /
• 2013

In this study, the moisture content, charge discharge current, electrostatic capacity and dielectric loss tangent are measured for the specimen of bisphenol type epoxy resin which is mixed with squared amorphous silica filler and dipped in hot water of $50^{\circ}C$ for 169 days. The results of this study are listed below. The longer of deposition day, the charge and discharge current was increased. It is considered that the reason is because there was water attack through the squared silica surface. The longer of deposition day, the absorption rate of all specimens was increased. It found that the absorption rate reached saturated state after 100 days. The higher frequency and the longer of deposition day, the $tan{\delta}$ was decreased. Also, It found that the $tan{\delta}$ and electrostatic capacity of the specimen which is mixed with squared filler are greater.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 춘계학술대회 논문집
• /
• pp.35-42
• /
• 1996

In this Paper, optical absorption were performed on LB films of binary mixtures of three kinds of merocranine dyes DO, DS, and 6Me-BS, where DS and 6Me-DS form J-like aggregates but not DO in single component films. The observed optical absorption spectra of mixed films were markedly defendent on the combination of dyes. [6Me-DS]$\sub$1-x/[DOl]$\sub$x/ LB films show a sharp red shifted J-like band peak in the whole concentration range. We found the formation of f aggregates in a mixed merocyanine dyes containing a non J-aggregate forming dye DO, in a single component case. Farther investigations on the present and other mixed-dye films will be needed to clarify these points.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 추계학술대회 논문집
• /
• pp.195-198
• /
• 1996

In conducting systems based on LB films, TCNQ derivatives have been extensively studied as electron acceptor molecules. We have investigated the optical, electrical, and magnetic properties of Viologen-(TCNQ￣)$_2$LB films. In UV/visible absorption measurements, we have observed TCNQ￣ peak at 380 nm and dimer peak at 620 nm. The electron spin resonance measurements infer that Viologen-(TCNQ￣)$_2$LB film exhibits anisotropic properly. In other words, the LB film shows angular dependence. Iodine doping affects the degree of charge transfer and the conductivity of the films. The UV/visible absorption spectra of the LB film doped with I$_2$show peaks at near 400~430 nm and there is no dimer absorption peak. The in-plane electrical conductivity of the undoped film is approximately 4.2$\times$10$^{-6}$ S/cm.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 추계학술대회 논문집
• /
• pp.401-404
• /
• 1996

Optical absorption were performed on LB films of binary mixtures of three kinds of merocyanine dyes [DO], [DS], and [6Me-DS], where [DS] and [6Me-DS] from J-like aggregates but not [DO] in single component films. The observed optical absorption spectra of mixed films were markedly dependent on the combination of dyes. [DS]$_{1-x}$ [DO]$_{x}$ LB films show a sharp red shift J-like band peak in the while concentration range. We found the formation of J-aggregates in a mixed merocyanine dyes containing a non J-aggregate forming dye [DO], in a single component case. Further investigations on the present and other mixed dye films will be needed to clarify these points.ts.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 춘계학술대회 논문집
• /
• pp.526-528
• /
• 1999

Epoxy resin has been used as matrix resin of advanced composites owing to ideally suitable properties and inherent physical and chemical properties for electrical and electronic insulation In this paper, in order to evaluate the performance of epoxy composites for out door insulation, variations of tracking resistance were investigated on the moisture absorption aging condition. Also, IPN methods were introduced in order to improve performance for out door use. As a result, it was confirmed that tracking resistance were degraded with boilling time. But, it was confirmed that specimen of IPN structure and KC-335 have the better tracking resistance properties than SIN structure by moisture absorption aging

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 추계학술대회 논문집
• /
• pp.53-56
• /
• 2000

Langmuir-Blodgett(LB) technique is the best candidate for the future molecular electronic devices. But, these molecular thin film devices require the bulk properties that are influenced by the molecular orientations. So, this is of current interest in molecular electronic device fabrications of new materials. In this study, quantitative evaluation of molecular orientation in LB films of PAAS was performed by comparing the absorption intensities of the FT-IR transmission and reflection-absorption spectra and the polarized UV/visible absorption spectra. It was found that the polar angle( $\theta$ ) of the dipole moment is about 68$^{\circ}$ and the tilting angle of the alkyl chain is about 11.5$^{\circ}$

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.156-159
• /
• 2000

In this paper, the physical and electrical properties of epoxy composites are investigated at boiling absorption condition to observe the influences of moisture. Also, in order to improve water resistance of matrix resin, IPN method was introduced and the influence was investigated. In order to analyze the basic physical properties of samples, scanning electron microscopy method was utilized, and impulse voltage dielectric strength was measured. As a result, it was verified that, in case of IPN samples, the ratio of moisture absorption was decreased due to the improvement of adhesion strength, and impulse voltage dielectric strength of SN sample was degraded abruptly as boiling time and filler content were increasing, while IPN samples were slowly degraded due to the improvement of adhesion strength.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.165-168
• /
• 2000

This paper presents the tracking resistance and mechanical strength due to boiling absorption of epoxy resin. The single network structure specimen(E series) formed of epoxy alone and interpenetrating polymer network(IPN) structure specimen(EM series) which epoxy resin was taken as first network and methacrylic acid resin as second network were manufactured. As adding $SiO^2$ filler classified by o[phr], 50[phr] and 100[phr] to those specimens, six kinds of specimens were manufactured and boiled in water during 2, 4, 8, 16, 32 and 64[hours]. As a result, it was confirmed that the tracking breakdown time of E series showed a abrupt decrease with boiling time increasing, but that of EM series was decreasing smoothly. Also, it was verified that the degrading rates of mechanical strength was lowerd according to improvement of adhension strength in case of EM series.