• Corrosion Science and Technology
• /
• v.21 no.2
• /
• pp.130-137
• /
• 2022

In this work, the degradation of high-pressure superheater tubes exposed to the flame of a duct burner in a heat recovery steam generator of a district heating system was evaluated. To assess the deterioration of the used superheater tube, the microstructure, microhardness, and tensile properties were investigated by comparison to an unused tube. The study found that a fin bound at the outer surface of the used tube became fragile only in the location facing the flame. This indicates that the tube was directly exposed to the flame from the duct burner or underwent abnormal overheating. While the unused tube showed a uniform value in hardness and equiaxial grain structure, the used tube revealed a decrease in hardness up to 105 HV and an increase in grain size with a plate-like morphology in the location facing the flame. The coarsening of the grain structure by the flame weakened the mechanical properties of yield strength, tensile strength, and elongation.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.32 no.4
• /
• pp.136-142
• /
• 2022

The crystal structure, grain growth behavior, and dielectric properties of BaTiO₃ have been studied with the addition of Dy₂O₃. The powders were synthesized at ratios of (100-x)BaTiO₃-xDy₂O₃ (mol%, x = 0, 0.5, 1.0, 2.0) by a conventional solid-state synthesis, and the powder compacts were sintered at 1250℃ for 2 hours in air. As the amount of added Dy₂O₃ was increased, the crystal structure of the sintered samples changed from a tetragonal to a pseudo-cubic structure, and the tetragonality decreased. In addition, a secondary phase of Ba₁₂Dy_4.67Ti₈O₃₅ appeared when Dy₂O₃ was added. The average grain size after sintering decreased and abnormal grains appeared as the amount of Dy₂O₃ increased. It can be explained that the grain growth behavior of the Dy₂O₃ added-BaTiO₃ occurs due to the two-dimensional nucleation and growth, and is governed by the interface reaction. Further, the correlation between crystal structure, microstructure, and dielectric properties was discussed.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.27 no.3
• /
• pp.198-205
• /
• 1982

In 1980, rice was considerably damaged by abnormal low temperature. In this paper, to determine the effect of low temperature on the growth and nutrition of rice, the experiment were carried out: varietal response to low temperature in the region with different elevations. Regional differences of heading response to low temperature were observed among varieties. The difference of days between regions were bigger in tongil lines than Japonica lines. Especially, Milyang 42 and Hangangchalbeo might belong the cold suceptible group, since the varieties were severely delayed their heading in the high mountainous region as comparred to plain region. The delay of heading with low temperature was brought out grain sterility, and fertility and ripening ratio is influenced cold tolerance and elevations, and it's decreased yield. Varieties with higher grain sterility by low temperature have higher total nitrogen content, but tended to have lower potassium and phosphate contents in the flag leaf. High content of total nitrogen, low contents of potassium and silicate were observed in the sterilized grain chaff an the opposite result were noted in the ferilized grain chaff at the ripening stage. The results reveal that the balance of these mineral element may play an important role in ripening and possibly cold tolerance.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.12
• /
• pp.1096-1100
• /
• 2008

This report examines the variations on structural properties of $SnO_2$ thin films deposited by using thermal chemical vapor deposition techniques with different oxygen flow gas. TEM showed some of the interface to be atomically rough. The aspects of the boundary shape and growth behavior agree well with the theory of interface growth. The electron diffraction showed that the roughness was changed as the different oxygen flow gas increased. These measurement results suggested that the number of interface facet and abnormal grain growth were related oxygen flow gas.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.3
• /
• pp.208-213
• /
• 1998

Microwave dielectric properties of $BiNbO_4$ containing CuO and $V_2O_5$(BN ceramics). BN ceramic with 0.07wt% $V_2O_5$ and 0.03wt% CuO (BNC3V7) was sintered at $900^{\circ}C$ where it is possible for these to be co-fired with Ag electrode. The dielectric constant of 44.3, TCF (Temperature Coefficient of resonance Frequency) of 2 ppm/$^{\circ}$ and Q${\times}f_o$ value (product of Quality value and resonance Frequency) of 22,000GHz could be obtained from those ceramics. It is observed that orthorhombic structure was stable $1000^{\circ}C$. As sintering temperature increases, the dielectric properties decreased. The main reasons were abnormal grain growth and the main peak of triclinic moved from the main peak of orthorhombic.

• Journal of the Korean Ceramic Society
• /
• v.27 no.4
• /
• pp.548-552
• /
• 1990

Effects of binder addition method during compacting on microstructural change and magnetic characteristics of Sr-ferrite system was investigated. Used binders were PVA and PEG, which were added separately or simultaneously. After compacts were heated at 50$0^{\circ}C$ for 3hr in air for burning out all the binders, they were sintered at 125$0^{\circ}C$ for 2h. Based on results, in the case of using the two binders simultaneously, comparing to single binder system, compacted density was somewhat higher but sintered density was rather lower, and abnormal grain growth was accelerated. According to these sintering characteristics, remanent magnetization and coercive force were also diminished.

• Journal of the Korean Ceramic Society
• /
• v.28 no.11
• /
• pp.926-934
• /
• 1991

The effect of aggregates on the forming and sintering behaviors of BaTiO3 was studied. Aggregates and deaggregates of fine crystallite were obtained by thermal decomposition of oxalate coprecipitates and subsequently crushing them with a press, respectively. Large voids formed by packing of aggregates were not easily eliminated despite the successive destruction of aggregates with increasing forming pressure. As a result, compacts of aggregates showed inhomogeneity with larger mid-pore size and broader pore size distribution with respect to those of deaggregates. This inhomogeneity caused differential shrinkage and consequental internal stress, which retarded densification. The differential sintering increased the size of mid-pores in the initial stage, and formed duplex structure composed of dense region with abnormally grown grains and porous region with fine grains. The driving force of this abnormal grain growth shown in the specimens of aggregates was attributed to the minimization of the elastic strain energy due to internal stress.

• Journal of the Korean Ceramic Society
• /
• v.26 no.4
• /
• pp.453-458
• /
• 1989

Aluminum nitride powder prepared from the hydroxides, AlOOH and Al(OH)3 which were obtained by hydrolysis of Al-isopropoxide, was densified at 1750 and 180$0^{\circ}C$ for 60 min by hot-pressing under the pressure of 25kg/$\textrm{cm}^2$. Theoretical density could be obtained at 175$0^{\circ}C$. Their flexural strengths were 450MPa and 395MPa for the specimens obtained from Al(OH)3 and AlOOH, respectively. There was no remarkable change in flexural strength up to 100$0^{\circ}C$. Fracture toughness values were 3.50MN/m3/2 for Al(OH)3 and 3.11MN/m3/2 for AlOOH. It is assumed that these differences in mechanical properties are due to the abnormal grain growth for the AlN ceramics obtained from AlOOH.

• Journal of the Korean Ceramic Society
• /
• v.30 no.12
• /
• pp.1029-1038
• /
• 1993

The microstructures of aluminas, included of dissolved CaO as $\alpha$-alumina seeded pseudo-boehmite hydrosol was gelled in plaster mold and doped of MgO as dipping of calcines(120$0^{\circ}C$-2h) into Mg-nitrate solution, were compared to the one of which additives are excluded during the gellation. It was formed the boundary layer of 300~350${\mu}{\textrm}{m}$ distance from surface to the inside, containing of approximately 500ppm CaO by dissolved Ca from plaster mold. As the MgO addition to the boundary layer with dissolved CaO, the microstructure of the layer was uniformed and inhibited the grian growth, compared to one of that additives be excluded specimen and of MgO doped-inside region. This result was considered as abnormal grain growth and effect of flat boundary formation be appeared by effects of dissolved CaO, were decreased by MgO co-doping.

• Journal of the Korean Ceramic Society
• /
• v.56 no.3
• /
• pp.269-276
• /
• 2019

This article reports on the conditions required for the growth of crystalline boron films on silicon substrates by hot filament chemical vapor deposition method. The reactive gas was 3% diborane diluted in hydrogen. The films were characterized by optical, electronic, and atomic force microscopies; x-ray diffraction; and energy dispersive, electron energy loss, Raman, x-ray photoelectron, and Auger spectroscopies. The parameters that affect the morphologies of the films have been investigated. It was concluded that faceted crystals are produced at low B₂H₆ flows and working pressures below 200 mT. α-boron is produced between 530 and 600℃. Deposition outside this range produces thin films with a wide variety of morphologies. This result indicates that the films crystallize through a process called "abnormal or discontinuous grain growth." It is assumed that this is due to the anisotropic surfaces of boron allotropes.