• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 가을 학술발표회논문집(I)
• /
• pp.253-258
• /
• 2000

Recently, the area of design optimization, especially structural optimization, has been and to be a continuous active area of research. And the design optimizations of port facilities have been achieved by many other civil engineers. But the design optimization of port facilities were limited to the design optimization of the breasting dolphin. This paper invested the design optimization of mooring pier and the foundations of mooring pier was suggested considering the convenience of repair and reinforcement work. The mooring pier devised with prestressed precast concrete panel and rigid frame welded wide flange beam to steel pipe pile. To accomplish the design optimization of mooring pier, the Augmented Lagrangian Multiplier Method(ALM) of ADS(Garret N. Vanderplaats) optimization routine, BFGS method as optimizer and Golden Section Method as one dimensional search were utilized. As a result, thirty percent of material cost for construction was reduced by design optimization. The tensile stress of concrete panel and bottom flage was critical constraints under service load. So, using high strength concrete and steel will be economical. And lots of initial values must be invested to accomplish the design optimization in design procedures.

• 한국항공운항학회지
• /
• 제21권2호
• /
• pp.33-39
• /
• 2013

Multilateration(MLAT) may complement secondary surveillance radar and also act as a real-time backup for the ADS-B system. This System is using time difference of arrival (TDOA) and based on triangulation principle. Each TDOA measurement defines a hyperbola describing possible aircraft locations. The accuracy in MLAT system depends on the positional relationship of the receiver and aircraft. There are various algorithms to localize aircraft based on TOA estimation. In this paper, we use least square method and extended Kalman filter and compare their results. Study results show that the extend Kalman filter provides a better performance than the least square method.

• 한국생산제조학회지
• /
• 제18권6호
• /
• pp.576-584
• /
• 2009

Up to now, it has been said that no satisfactory computer solution has been found for synthesizing four-bar linkage based on the prescribed coupler link curve. In our study, an algorithm has been developed to improve the design synthesis of four bar linkage based on the 5 precision points method. The suggested algorithm generates the desired coupler curve by using NURBS, and then the generated curve approximates as closely as possible to the desired curve representing coupler link trajectory. Also, when comparing each generated curve by constructing the control polygon, rapid comparison is easily achieved by applying convex hull of the control polygon. Finally, an optimization process using ADS is incorporated into the algorithm based on the 5 precision point method to reduce the total optimization process time. As for examples, two four bar linkages were tested and the result well demonstrated the effectiveness of the algorithm.

• Nuclear Engineering and Technology
• /
• 제49권6호
• /
• pp.1234-1239
• /
• 2017

Basic research on the accelerator-driven system is conducted by combining $^{235}U$-fueled and $^{232}Th$-loaded cores in the Kyoto University Critical Assembly with the pulsed neutron generator (14 MeV neutrons) and the proton beam accelerator (100 MeV protons with a heavy metal target). The results of experimental subcriticality are presented with a wide range of subcriticality level between near critical and 10,000 pcm, as obtained by the pulsed neutron source method, the Feynman-${\alpha}$ method, and the neutron source multiplication method.

• 한국방재학회 논문집
• /
• 제10권3호
• /
• pp.31-38
• /
• 2010

본 연구에서는 교량 구조물-궤도 종방향 상호작용, 교량 구조물-차량 상호작용을 고려한 신뢰성 최적설계 방법을 제안하고, 알고리즘의 개발을 통하여 본 연구에서 제안한 방법의 효율성을 검증하였다. 구조해석 프로그램은 ABAQUS를 사용하였으며, 최적화 방법은 Automated Design Synthesis(ADS)에서 신뢰성면에서 우수한 ALM-BFGS방법을 사용하였다. 일반적으로 ALM-BFGS방법은 최적해 방향을 탐색하는데 있어 1방향 탐색을 하지 않으며 Push-Off Factor 값이 보통 0.1~0.2에서 대부분 수렴하나 본 연구에서는 'Heuristic Decision Method' 의하여 결정된 Push-Off Factor 값이 90일 때 1방향 탐색인 Golden Section Method의 적용이 필요하였으며, 알고리즘이 잘 수렴함을 확인하였다. 구조물-궤도 종방향 상호작용, 구조물-차량의 상호작용에 의한 응답을 제약조건으로 설정하여 단면 설계시 반영될 수 있도록 하였다. 본 연구는 구조물-궤도 종방향 상호작용 및 구조물-차량 상호작용을 고려한 설계기법에 대한 효율성 및 경제성을 증명하기 위하여 5${\times}$(1@50m) 2주형 강합성 거더교에 대한 최적설계를 수행하였으며, 본 연구에서 제안하는 상호작용을 고려하는 설계기법이 기존의 상호작용을 고려하지 않은 설계방법보다 경제적이며 효율적임을 확인하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1994년도 가을 학술발표회 논문집
• /
• pp.175-181
• /
• 1994

In order to accelerate the rate of consolidation settlement and to gain a required shear strength for a given soft clay deposit, the preloading technique combined with a vertical drainage system has been widely applied. In this study, the theory of axisymmetric concolidation, which considers the variation of compressibility and permeability during the consolidation process, has been developed. Smear and well resistance effects are also considered. Furthermore, several back-analysis schemes such as simplex method, BFGS method, and ADS have been adopted in the axisymmetric consolidation program(AXICON). The measured data in the first stage of consolidation are utilized to predict the subsequent consolidation behavior.

• 한국항공운항학회지
• /
• 제20권4호
• /
• pp.14-20
• /
• 2012

A properly determined separation minima applied in Air Traffic Management(ATM) is critical for safe and efficient aircraft operations. The separation minima is primarily determined by the accuracy performance of surveillance system, and, due to the stringent aviation safety standard, the position accuracy of the surveillance system must be estimated with a high level of reliability. This study proposed a method for estimating the position accuracy of surveillance system with a relatively small amount of data by finding upper confidence limit instead of maximum likelihood values of unknown parameters. Through the proposed method, it is possible to determine a required separation minima with a more reliability in the face of data scarcity which often occurs when we implement a new surveillance system such as Automatic Dependent Surveillance-Broadcast (ADS-B).

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.128-133
• /
• 2002

The main obstacle to high track density in HDD is the structural resonances of the suspension. The most critical mode is sway mode and second torsion mode, when a data is read and written. It is common fact that the effect of two modes is smaller when a thickness is bulky. But the stiffness of suspension is smaller, the slider can follow a disk better. Because these two fact are reciprocal, a compromise is needed. So we investigated another method to improve band width without changing of the thickness of suspension but with changing of the shape. In this paper, we use two method - Sensitivity analysis and SIP using ADS. And we obtained the optimized value close to target value.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1999년도 봄 학술발표회 논문집
• /
• pp.78-85
• /
• 1999

In this study, I-type girders used as main members of a two span continuous steel bridge, are optimally designed by a Load and Resistance Factor Design method(LRFD) using an numerical optimization method. The width, height web thickness and flange thickness of the main girder are set as design variables, and light weight design is attempted by choosing the cross-sectional area as an object function. The main program is coded with C++ and connected with optimization modul ADS, which is coded with FORTRAN. The results of the program show that the stress constraints of noncomposite section during the initial construction stage become active in the positive moment area and the service limit state constaints become active in the negative moment area.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 하계종합학술대회 논문집(1)
• /
• pp.185-188
• /
• 2001

In this paper, we design and implement high-power amplifier with 18 watt for W-CDMA repeater. We simulate microwave circuits using RF simulator, ADS1.3 and optimize the circuit to obtain the linear and high power using Harmonic balance method. Harmonic balance is an excellent method in the analysis of nonlinear system. The HPA is fabricated on tefron substrate($\varepsilon_{{\gamma}}$=3.48, h=0.5mm, T=0.035mm). From the measured result, the HPA has gain of 52dB, 1 dB compression power of 52.8dBm and good ACPR (Adjacent Channel Power Radio) performance.l Power Radio) performance.