• Korean Journal of Materials Research
• /
• v.13 no.9
• /
• pp.593-597
• /
• 2003

Anodic aluminum oxide (AAO) membrane was made of aluminum sheet (99.6%, 0.2 mm thickness). The regular array of hexagonal nano pores or channels were prepared by two step anodization process. A detail description of the AAO fabrication is presented. After the 1st anodization in oxalic acid (0.3 M) at 45 V, The formed AAO was removed by etching in a solution of 6 wt% $H_3$$PO_4$＋1.8 wt% $H_2$$CrO_4$. The regular arrangement of the pores was obtained by the 2nd anodization, which was carried out in the same condition as the 1st anodization. Subsequently, the alumina barrier layer at the bottom of the channel layer was removed in phosphoric acid (1M) after removing of aluminum. Pore diameter, density, and thickness could be controlled by the anodization process parameters such as applied voltage, anodizing time, pore widening time, etc. The pore diameter is proportional to the applied voltage and pore widening time. The pore density and thickness can be controlled by anodization temperature and voltage.

• Journal of the Korean institute of surface engineering
• /
• v.54 no.5
• /
• pp.213-221
• /
• 2021

In order to improve the energy density and safety of Li-ion batteries, the development of a separator with high thermal stability and electrolyte wettability is an important desire. Thus, the ceramic separator to replace the polymer type is one of the most promising materials that can prevent short-circuit caused by the formation of dendrite and thermal deformation. In this study, we introduce the fabrication of various anodic aluminum oxide membranes for the application of Li-ion battery separators with the advantages of improved mechanical/thermal stability, wettability, and a high rate of Li⁺ migration through the membrane. Two different types of through-holes and branched anodic aluminum oxide membranes are well used in lithium-ion battery separators, however, branched anodic aluminum oxide membranes exhibit the most improved performance with capacity (126.0 mAh g^-1 @ 0.3C), capacity drop at the high C-rate (30.6 %), and low internal resistance (8.2 Ω).

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.368-370
• /
• 2007

AAO(Anodic Aluminum Oxidation) method has been known that it is practically useful for the fabrication of nano-structures and makes it possible to fabricate the highly ordered nano masters on large surface and even on the 2.5 or 3D surface at low cost comparing to the expensive e-beam lithography or the conventional silicon processing. In this study, by using the multi-step anodizing and etching processes, highly ordered nano patterned master with concave shapes was fabricated. By varying the processing parameters, such as initial matter and chemical conditions; electrical and thermal conditions; time scheduling; and so on, the size and the pitch of the nano pattern can be controlled. Consequently, various alumina/aluminum nano structures can be easily available in any size and shape by optimized anodic oxidation in various aqueous acids. The resulting good filled uniform nano molded structure through hot embossing molding process shows the validity of the fabricated nano pattern masters.

• Journal of the Korean institute of surface engineering
• /
• v.51 no.6
• /
• pp.393-399
• /
• 2018

Formation behavior of aluminum anodic oxide (AAO) films on Al6061 alloy was studied in view of thickness, morphology and defects in the anodic films in 20 vol.% sulfuric acid solution at a constant current density of $40mA/cm^2$, using voltage-time curve, observation of anodized specimen colors and surface and cross-sectional morphologies of anodic films with anodization time. With increasing anodizing time, voltage for film formation increased exponentially after about 12 min and its increasing rate decreased after 25 min, followed by a rapid decrease of the voltage after about 28 min. Surface color of anodized specimen became darker with increasing anodizing time up to about 20 min, while it appeared to be brighter with increasing anodizing time after 20 min. The darkened and brightened surfaces with anodizing time are attributed to an increase in thickness of porous anodic oxide film and a chemical damage of the films due to heat generated by increased resistance of the film, respectively. Cross-sectional observation of AAO films revealed the formation of defects of crack shape at the metal/oxide interface after 15 min which prevents the growth of AAO films. Width and length of the crack-like defect increased with anodizing time up to 25 min of anodizing, and finally the outer part of AAO films was partly dissolved or detached after 30 min of anodizing, resulting in non-uniform surface structures of the AAO films.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.3
• /
• pp.159-162
• /
• 2016

We studied an electrolyte-dielectric metal (EDM) device based on a Si₃N₄ layer-coated anodic aluminium oxide (AAO) template for chemical sensors. The AAO templates were fabricated using a two-step anodization procedure at 0℃ and 70 V in 0.3 M oxalic acid, after which the Si₃N₄ was deposited on them using plasma enhanced chemical vapor deposition (PECVD). The average pore size was approximately 106 nm and the depth of the AAO templates was 24.6 nm to 86.5 nm. The Si₃N₄ layer-coated AAO is more stable than a single AAO template.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.102.1-102.1
• /
• 2015

플라즈마를 이용한 건식식각공정은 식각하고자 하는 기판과 더불어 챔버 내부를 구성하고 있는 부품들이 플라즈마에 함께 노출되는 환경이다. 챔버 내부가 장시간 플라즈마에 노출되어 열화 되면 기판의 불량을 야기하는 오염입자의 발생이 증가하므로 양산 공정에서는 그 때마다 내부 부품을 교체하여 청정한 공정 환경을 유지시킨다. 공정 챔버의 내부 부품은 플라즈마로 인한 열화를 방지하기 위하여 내플라즈마성이 우수하다고 알려진 코팅처리를 하여 사용한다. 금까지 플라즈마 식각 공정에 관한 연구는 식각하고자 하는 기판관점에서 활발히 이루어져 왔으나 내플라즈마성 코팅소재 관점에서의 연구 보고는 미미한 실정이다. 본 연구에서는 장시간의 양산공정을 모사하는 가혹한 플라즈마 조건에서 $CF_4/O_2$ 혼합가스를 사용하여 AAO (Anodic Aluminum oxide)피막의 오염입자 특성을 실시간 모니터링 하는 동시에 OES 분석을 수행하여 내플라즈마성 코팅소재의 오염입자 발생 메커니즘에 대하여 분석하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.106-107
• /
• 2007

We fabricated anodic aluminium oxides (AAO) on Si and sapphire substrates from the electrochemical reactions of thin AI films in an aqueous solution of oxalic acid. The thin AI films have deposited on Si and Sapphire substructure by using E-beam evaporation and thermal evaporation, respectively. The formation of AAO structures has investigated from FE-SEM measurement image and showed randomly distributed phase of nanoholes instead of the periodic lattice of photonic crystals. The AAO structure on sapphire shows the double layers of nanoholes.

• Tribology and Lubricants
• /
• v.27 no.4
• /
• pp.193-197
• /
• 2011

Friction behavior of nanoporous anodic aluminum oxide(AAO) film was investigated. A 60 ${\mu}m$ thick AAO film having nanopores of 45 nm diameter with 105 nm interpore-diatance was fabricated by mild anodization process. The AAO film was then saturated with paraffinic oil. Reciprocating ball-on-flat sliding friction tests using 1 mm diameter steel ball as the counterpart were carried out with normal load ranging from 0.1 N to 1 N in an ambient environment. The morphology of worn surfaces were analyzed using scanning electron microscopy. The friction coefficient significantly increased with the increase of load. The boundary lubrication layer of paraffinic oil contributed to the lower friction at relatively low load (0.1 N), but it is less effective at high load (1 N). Plastic deformed layer patches were formed on the worn surface of oil-enriched AAO at relatively low load (0.1 N) without evidence of tribochemical reaction. On the other hand, thick tribolayers were formed on the worn surface of both oil-enriched and as-prepared AAO at relatively high load (1 N) due to tribochemical reaction and material transfer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.62-63
• /
• 2008

Photonic crystas were fabricated using an anodic aluminum oxide(AAO) mask on GaN diode. The Photonic crystal structure has been investigated from Atomic Force Microscope(AFM). The hole diameter and lattice constant of photonic crystal are 60nm and 105nm, respectively. Photoluminescence of photonic crystal was enhanced and optical interference was increased by photonic crystal effect.

• Applied Chemistry for Engineering
• /
• v.16 no.4
• /
• pp.461-473
• /
• 2005

Nanotechnology has attracted great attention as one of essential fields in modern science. In particular, the fabrication of nanostructures with nanometer dimension in size is the starting point and essential part of nanotechnology research. Anodic aluminum oxide (AAO) nanotemplate technique has many merits including ease of fabrication, low cost process, and nanotemplate fabrication in large area. Moreover, AAO nanotemplate technique can realize self-ordered hexagonal pore structure with extremely high aspect ratio which is difficult to achieve with conventional lithographic techniques. Simple control of pore dimensions such as diameter, length, and density by varying anodizing condition would be advantageous, too. AAO nanotemplate has been the topic of intensive investigations for the past decade due to above strong points, and the application to various fields of nanotechnology is expected. In this review paper, the fabrication and application of AAO nanotemplate are introduced.