• International Journal of Highway Engineering
• /
• v.7 no.3 s.25
• /
• pp.43-52
• /
• 2005

Highway classification is an essential part of defining design criteria of roads. This study is to classify highways by factor analysis. To accomplish the objectives, factor analysis is performed for classifying highways using the traffic data observed at the permanent traffic count points in 2004. A total off variables are applied : AADT, K factor, D factor, heavy vehicle proportion, day time traffic volume proportion, peak hour volume proportion, sunday factor, vacation factor and COV(Coefficient of Variation). The results of factor analysis show that variables are divided into two factors, which are the factor related to the fluctuational characteristics of traffic volume and the factor related to heavy vehicle and directional volume characteristics. According to the results of cluster analysis, 353 permanent traffic count points are categorized into such three groups as type I for urban highway, type II for rural highway, type III for recreational highway, respectively.

• The Journal of the Korea Contents Association
• /
• v.15 no.11
• /
• pp.582-590
• /
• 2015

Road type classification and K-factors are important role when design of number of lane. In this study not only classifies road type and estimating of K-factor but also economic evaluation tries for feasibility verification. Road type analysis results, time of day traffic volume variation, weekend-factor and vacation-factor are large in recreation roads. Weekday traffic volume and weekend traffic volume are similar patterns in provincial roads. AADT is high and time of day traffic volume variation is small in urban roads. In this study compares with economic analysis that designing of number of lane between KHCM's K-factor and this study K-factor. Economic analysis results, designed roads by this study's K-factor reduce cost about 4,708 hundred million won. So this study's K-factor is economical on provincial 4 lane roads.

• Journal of Korean Society of Transportation
• /
• v.28 no.2
• /
• pp.111-121
• /
• 2010

DHV (Design-Hour Volume) for the estimation of number of lanes is determined by design-hour factor (K). The design-hour factor is defined as the proportion between the 30th highest hourly volume and AADT and determines the level of road planning. However, the K-factor estimated by an existing method has a problem because the hourly volumes on holiday and weekend appear in the relatively low rank in real world in spite of expected high volumes. To improve this problem, this study make use of the concept of traffic demand in estimating the design-hour factor. After the congested hourly volumes transfer to traffic hourly demand, the K-factors are estimated on urban expressways and are compared to the existing K-factors. It is perceived that the new K-factors have more realistic values due to utilizing the traffic demand. reflecting the congested flow.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.11 no.6
• /
• pp.145-154
• /
• 2012

This paper analyzed the characteristics of traffic accidents in all tunnels on nationwide freeways and selected some various independent variables related to accident occurrence in tunnels. The study aims to develop reliable accident forecasting models using the various dependent variables such as the number of accident (no.), no./km, and no./MVK. Finally, reliable multiple linear regression models were proposed in this paper. This study tested the validity verification of developed models through statistics such as $R^2$, F values, multicollinearity, residual analysis. The paper selected the accident forecasting models considering the characteristics of tunnel accidents and two models were finally proposed according to two groups of tunnel length. In the selected models, natural logarithm of ln(no./MVK) is used for the dependent variable and AADT, vertical slope, and tunnel hight are used for the independent variables. The reliability of two models was proved by the comparison analysis between field data and estimating data using RMSE and MAE. These models may be not only effective in evaluating tunnel safety under design and planning phases of tunnel but also useful to reduce traffic accidents in tunnels and to manage the traffic flow of tunnel.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.1D
• /
• pp.23-30
• /
• 2006

The variation in the traffic volume on any given roads is the reflection of its user's economic activities and life patterns. And traffic volume flows in every hour usually take different charateristics depending on the location and the function of the roads. This study produced the Monthly Adjustment Factor, Weekly Adjustment Factor and Design hourly Factor, each of which is the index indicating the traffic volume charaterirstics on the highways leading to the recreation areas in the mountainous and seaside tourist sites. Applying these results, it might be possible to calculate the optimal AADT (Annual Average Daily Traffic) and DHV (Design Hour Volume), also be a help to establish a traffic management policy. Finally, it hopes to promote new version of KHCM (Korea Highway Capacity Manual) which includes traffic volume characteristics on recreation areas.

• Journal of Korean Society of Transportation
• /
• v.12 no.1
• /
• pp.137-149
• /
• 1994

The objective of study is to evaluate the effect of speed control hump on traffic operation and accidents. Three sites were investigated for the change of traffic accidents before and after the hump installation. Vehicle speeds approaching the hump were also analyzed. The study revealed that not only the number of traffic accidents but also the accident severity were significantly reduced by the installation of hump. Further, different types of traffic accidents with lower severity were observed after the hump installation. For the effect of speed reduction by hump, it was found that the speeds observed at 15m upstream of hump were in the range of 36~50 percent of approaching speeds which were not affected by (ie, without) the hump. Economic analysis of hump installation showed the benefit-cost ratio of 4.3 and 11.2 at two sites. Further analysis revealed that the benefit by the accident reduction exceeds the cost by speed reduction and installation capital if AADT is below 43,150 vehicles on two lane highways. It is recommended from the study that humps should be considered on two lane highways of high accident locations for excessive speeds to reduce traffic accidents and severity.

• Journal of Korean Society of Transportation
• /
• v.12 no.1
• /
• pp.151-172
• /
• 1994

The objective of study is to evaluate design standards related to the allowable truck speeds, taper length and sign requirements together with the operating practices and economic justification for climbing lanes. Field surveys were carried out on seven climbing lanes, three on two-lane and four on four-lane freeways. Data collected are traffic volume, speed, usage rate and delay. It is found that current design criteria for determining the length of climbing lane, taper lengths, and traffic sign requirements must be upgraded. It is also recommended that regulations on the use of climbing lane be established to make it more effective. Further, economic analysis revealed that the climbing lane is economically justified for two-lane and four-lane freeway if the AADT is over 4,577 and 5,116 vehicles respectively.

• Journal of the Korean Society of Safety
• /
• v.25 no.3
• /
• pp.131-136
• /
• 2010

This study deals with the accident models of arterial link sections by vehicle type. The objectives are to analyze the characteristics of accidents, and to develop the models by type. In pursuing the above, this study uses the data of 414 accidents occurred on 24 major arterial links in 2007. The main results analyzed are as follows. First, the number of accidents is analyzed to account for about 47% in passenger car, 15% in SUV and 10% in trucks. Second, 3 Poisson regression models which are all statistically significant are developed using passenger car, SUV and truck as dependant variables. Finally, AADT and the number of traffic islands as common variables, and the number of pedestrian crossings, lanes, connecting roads, intersections(4-Leg), rate of medians and the number of bus stops as specific variables of the models are selected.

• Journal of the Korean Society of Safety
• /
• v.25 no.4
• /
• pp.90-95
• /
• 2010

This study deals with the accident model of arterial link section in Cheongju. The objective is to develop the accident model of arterial link section using the logistic regression. In pursuing the above, the study uses the 258 accident data occurred at the 322 arterial link section. The main results are as follows. First, Nagellerke $R^2$ of developed accident model is analyzed to be 0.309 and t-values of variable that explains goodness of fit are evaluated to be significant. Second, the variables adopted in the model are AADT, the number of exit and entry. These variables are all analyzed to be statistically significant. Finally, the analysis of correct classification rate shows that the total accident of correct classification rate is analyzed to be 72.7% at the arterial link section.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.1913-1926
• /
• 2007

Number of highway lanes and level of service are based on the 30th, 60th or 100th highest hour volume of the target year. On the other hand, railroad design volume is generally expressed in average annual daily traffic (AADT). This procedure ignores attributes of railroad demand's concentration on peak days and hours. Actual data analysis represents railroad's peaking characteristics very similar to those of highways. Therefore it is necessary to set a procedure in selecting design volume for railroad planning. This study presents a concept and the calculating procedure for railroad design hourly volume to analyze effect of railroad investment.