• Journal of the Semiconductor & Display Technology
• /
• v.20 no.4
• /
• pp.108-113
• /
• 2021

In this paper, a totem pole PFC was structured in two methods with FET and diode for low-speed switch while GaN FET was used for high-speed switch. Internal power loss, power conversion efficiency and steady-state characteristics of the two methods were compared in the totem pole bridgeless PFC circuit which is widely applied in large-capacity and high-efficiency switching rectifier of 500W or more. In order to compare and confirm the steady-state characteristics under equal conditions, a 2kW class totem pole bridgeless PFC was constructed and the experimental results were analyzed. From the experimental results, it was confirmed that the low-speed switch operation has a large difference in efficiency due to the internal conduction loss of the low-speed switch at a low input voltage. Especially, input power factor and load characteristic showed no difference regardless of the low-speed switch operation.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2020.11a
• /
• pp.72-74
• /
• 2020

일반적으로 선박조종에 필요한 중요한 성능으로 보침성능, 변침성능, 선회성능, 정지성능을 중요하게 여긴다. 이러한 조종성능은 선체의 선형과 함께 타와 엔진으로 표현될 수 있으며 특히 엔진의 성능은 선박의 안전운항과 직결되어 있다. 따라서 선박이 충분한 출력을 확보하지 못하면 항내조선시 선박의 안전을 담보하기 힘들며 또한 황천항해시 외력을 이기고 선박을 안전하게 조선하기 힘들다. 본 연구에서는 2020년 4월 6일 발생한 밀라노브릿지 사고를 통해 선박의 엔진출력을 저해하는 요소인 프로펠러 레이싱, 공전현상, 벤틸레이션 현상에 대하여 고찰하고자 하며 이를 통하여 선박의 조종성능에 미치는 출력을 중요성에 대하여 강조하고자 한다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.2
• /
• pp.152-158
• /
• 1999

Due to high power ratings and low conduction loss, the TGBT has become more attractive in switching power supplies. However, its lower turn-on and turn-off characteristics than those of MOSFET cause severe switching loss and s switching frequency limitation. This paper proposes 2.4kW. 48V. high efficiency half-bridge DC-DC converter using p paralleled TGBT-MOSFET switch concept to use the merits of TGBTs and MOSFETs. Tn parallel switches. each of I TGBT and MOSFET plays its part during on-periods and switching instants. The switching loss is analyzed by l linearized modelling and the operation of the converter are investigated by simulation results.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.720-722
• /
• 2003

This paper Presents a design schemes to minimize torque ripple in 6/4 Switched Reluctance Motor (SRM) using transient Finite Element Analysis (FEA) in which the magnetic field is combined with a driving circuit. Pole arcs and switching angles are major design factors. If these design factors are considered independently, the enhancement of SRM Performance is restricted. Therefore, this paper proposes not only optimal combination of stator pole arc and rotor pole arc but also the turn-on and turn-off angles as a function of pole arcs. Especially, turn-on and turn-off angle are formulated from a voltage equation and feasible design ranges are suggested with variable speed.

• Korean Journal of Mineralogy and Petrology
• /
• v.36 no.3
• /
• pp.213-220
• /
• 2023

In this study, we report the effect of starting materials on the grain size in a multi-component system at high pressure experiments. We used two different starting materials, glass and nano powders, to synthesize bridgmanite in the reduced conditions in the presence of calcium-ferrite-phase MgAl₂O₄ to compared the grain size of synthesized samples. After synthesizing the sample at 40 GPa, 2000 K for 20 hrs, the sample from glass showed the grain size of 50-200 nm whereas the one from nano powders has ~500 nm of grains. This difference may come from 1) the temperature of 2000 K which is low enough for glass starting materials to make more crystal nucleis than to grow crystal size or 2) the possible difference in the redox state of starting materials. It is suggested that the using of nano powders is better to synthesize bigger grains in high pressure experiments with multi-component systems rather than using glass starting materials.

• Proceedings of the KIPE Conference
• /
• 2013.11a
• /
• pp.17-18
• /
• 2013

본 논문에서는 자동차의 연료 절감을 위한 ISG(Idle Stop & Go) 시스템용 양방향 DC-DC 컨버터를 개발하였다. ISG 시스템 사양에 따라 효율 및 부피를 고려하여 3상 비절연 하프브리지 컨버터를 제안하였으며 또한 프리스케일사의 5643L MCU를 이용하여 디지털 제어기를 개발하였다. 1.8kW급 시작품을 통해 타당성을 검증하였으며 부피는 3.4L, 승 강압시 정격부하효율은 각각 95.1%, 95.5%이며 최고효율은 96.1%, 96.4%를 달성하였다.

• Proceedings of the KIPE Conference
• /
• 2003.07a
• /
• pp.62-65
• /
• 2003

We considered of the efficiency for the Buck+Half bridge converter This converter has advantages of applications for a low output voltage, a high output current and a wide input voltage. Developed the Buck converter ratings and the Half Bridge converter ratings are 36$\~$72V Input and 22V/5A output, 19$\~$24v input and 3.3V/30A output, respectively. Buck converter is operated with zero voltage switching process to reduce the switching losses. The 80.1 $\~$97.6$\%$ of the efficiency is measured at 18.4 $\mu$H output filter inductance of Buck convertor. In Half Bridge convertor, the 86$\~$96.4$\%$ of the efficiency is measured at 100kHz switching frequency with PQI core.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.19 no.4
• /
• pp.476-482
• /
• 2016

In this study, a method using single Wheatstone bridge flexure has been presented to measure hinge moment acting on control surfaces of wind tunnel models. The structural simplicity of the flexure reduces difficulty regarding gauging and wire-routing, and also makes it feasible to install flexures even inside thin wings. Some flexures were designed and fabricated under typical aerodynamic loads in wind tunnel test, and the strains on the flexure according to applied loads were compared with the result of the analysis by finite element method. The relation between applied loads and output signals showed good linearity, and the standard deviation on the residual errors from linear equation obtained by least square method was within 1.0 % of the maximum design moments. In addition, the FEM analysis on the thickness of load-connecting part of the flexure showed that the sensitivity was improved as the thickness became thin as much as desired to avoid buckling.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.4
• /
• pp.740-746
• /
• 2009

Two step serial load induction superheater has been proposed using resonance type induction heat method in this paper. Heat method is a type of flowing the electron induction and current to special alloy heater in body from external heat coil with non-contact method. Inverter was a full bridge serial load resonance type and inductor was used as load in LC resonance design to maximize the efficiency. The developed system is a new heat exchanging method combined with electromagnetic induction heater and fluid movement, ana very accurate to control of heating the gas, liquid and evaporated mass, so on without combustion process.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.4
• /
• pp.509-516
• /
• 2009

This paper is the study on improving the coefficient of utilization of material in deep drawing process. Cylindrical cup drawing process is widely used in sheet metal forming process. The blank shape is one of the important things in sheet metal forming process. It is produced for the bridge of blank in a blanking process. The coefficient of utilization of material is much effected by this bridge of blank. This study offered a new process method to reduce the loss of material. The new blank shape offered and manufactured by new process method is investigated by a finite element method and the experiment. Then the wrinkling, the punch load, the thickness distribution is observed. This result is different from the result of circular blank process. And it is got that the Max strain, the wrinkle and the height of the wrinkle are effected by the holding force and the punch load. As a result, if the processing optimum condition is found, the loss of material will be reduced. It is necessary to research systematically about determining the optimum value of process variables.