• International Journal of Naval Architecture and Ocean Engineering
• /
• v.8 no.5
• /
• pp.442-455
• /
• 2016

The resistance and seakeeping performance of a high-speed monohull vessel were investigated through a series of model tests in a towing tank. The hull had a slender wave-piercing bow, round bilge, and small deadrise angle on stern. Tests on the bare hull in calm water were first conducted and tests on spray rails followed. The spray rails were designed to control the flow direction and induce a hydrodynamic lift force on the hull bottom to reduce trim angle and increase rise of the hull. The maximum trim of the bare hull was $4.65^{\circ}$ at the designed speed, but the spray rails at optimum location reduced trim by $0.97^{\circ}$. The ship motion in head seas was examined after the calm water tests. Attaching the rails on the optimum location effectively reduced the pitch and heave motion responses. The vertical acceleration at the fore perpendicular reduced by 11.3%. The effective power in full scale was extrapolated from the model test results and it was revealed that the spray rails did not have any negative effects on the resistance performance of the hull, while they effectively stabilized the vessel in calm water and waves.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.8
• /
• pp.831-836
• /
• 2014

In this study, high temperature integrity evaluation on a pressure vessel of the expansion tank operating at elevated temperature of $510^{\circ}C$ in the sodium test facility of the SEFLA(Sodium Thermal-hydraulic Experiment Loop for Finned-tube Sodium-to-Air heat exchanger) to be constructed at KAERI has been performed. Evaluations of creep-fatigue damage based on a full 3D finite element analyses were conducted for the expansion tank according to the recent elevated temperature design codes of ASME Section III Subsection NH and French RCC-MRx. It was shown that the expansion tank maintains its integrity under the intended creep-fatigue loads. Quantitative code comparisons were conducted for the pressure vessel of austenitic stainless steel 316L.

• Journal of Power System Engineering
• /
• v.14 no.3
• /
• pp.5-12
• /
• 2010

The purpose of this study is to analyze heterogeneous distribution of branch-like structure at downstream region of inner spray. The previous many studies about diesel spray structure have yet stayed in the analysis of 2-D structure, and there are very few of informations which are concerned with 3-D analysis of the structure. The heterogeneous distribution of droplets in inner spray affects the mixture formation of diesel spray, and also the combustion characteristics of the diesel engines. Therefore, in order to investigate 3-D structure of evaporative spray the laser beam of 2-D plane was used in this study. Liquid fuel was injected from a single-hole nozzle (l/d=5) into a constant-volume vessel under high pressure and temperature in order to visualize the spray phenomena. The incident laser beam was offset on the central axis. From the images analysis taken by offset of laser beam, we examine formation mechanism of heterogeneous distribution by vortex flow at the downstream of the diesel spray. As the experimental results, the branch-like structure formed heterogeneous distribution of the droplets consists of high concentration of vapor phase in the periphery of droplets and spray tip of branch-like structure. Also the 3-D spatial structure of the evaporative diesel spray can be verified by images obtained from 2-D measurement methods.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.12 no.3
• /
• pp.125-130
• /
• 1979

In this paper, the noise pressure propagated in the air on account of the engine revolution of a stern trawler, Sae-Ba-Da(G. T. 2275.71) was measured at the check points No.1 through No.43 when the vessel was cruising, towing nets, and drifting. The experiment was carried out in the period from August 23 to October 22, 1978 at the locations of lat. $33^{\circ}$ 47'N, long. $127^{\circ}$ 34'E; lat. $34^{\circ}$ 24'N, long. $128^{\circ}$ 23'E; and lat. $6^{\circ}$ 01'N, long. $108^{\circ}$ 04'E. In case of cruising, noise on the weather deck came from funnel noise. The highest noise pressure was 92dB at observation point No.9 where tile noise pressure from main engine was 105dB when the engine was operated at 730rpm and $12^{\circ}$ sorely propeller pitch. The noise measured was reduced to 90dB at observation point No.9 when the screw propeller pitch was changed to $8^{\circ}$ that resulted in reduction of engine to 103dB. In case of towing net, the main engine revolution and screw propeller pitch was fixed at 730rpm and $8^{\circ}$ respectively. But the engine noise pressure was increased up to 106dB due to the towing resistance by 14 tons of the nets, and the noise pressure was 90dB at No.9 point. A hight noise was also generated from screw because of the towing reoistance and could be measurable even in the wall of the insulated freezing room. When the vessel was drifting: the noise pressure from the generator operated, at 720rpm was 100dB. This caused 87dB noise pressure at No.9 point. The noise pressure in the boarding or residence sections was 45 to 60dB in each case of cruisinrg towing net or drifting but it was so high as 82dB on the open deck that voice could hardly be heap.

• Journal of the Korean Institute of Navigation
• /
• v.12 no.2
• /
• pp.23-32
• /
• 1988

This paper offers a method of magnetic compass adjustment for the vessel alongside the wharf using newly designed magnetic north former, which makes the same magnetic field-change as the turning vessel does. The characteristics of the magnetic north former was examined by observing the deviation curves of the magnetic compass installed on the compass deviascop at laboratory. The magnetic north former consists of A and B arms which hold the permanent bar magnets at the both ends of each arm. The arm is to rotae in the horizontal plane about the vertical axis fixed at the center boss of the magnetic compass and it is to compensate the horizontal plane about the vertical axis fixed at the center boss of the magnetic compass and it is to compensate the horizontal component of the earth's field. The B arm makes the artificial magnetic north around the magnetic compass for every ship's heading. The results of investigation are summarized as follows ; 1. The observation and correction of magnetic compass deviation can be done without swinging the ship, of the effect of D coefficient is negligible. 2. The residual deviation curve of the magnetic compass depends on the accuracy of deduced value of ship's multplier($\lambda$). 3. The errors due to the inaccuracy of deduced value of ship's multiplier change in the same way as the B and C coefficient do.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.591-596
• /
• 2000

Flow through compliant tubes with linear taper in wall thickness is numerically simulated by finite element analysis. Two models are examined: a planar two-dimensional channel, and an axisymmetric tube. For verification of the numerical method, flow through a compliant stenotic vessel is simulated and compared to existing experimental data. Computational results for an axisymmetric tube show that as cross-sectional area falls with a reduction in downstream pressure, flow rate increases and reaches a maximum when the speed index (mean velocity divided by wave speed) is near unity at the point of minimum cross-section area, indicative of wave speed flow limitation or "choking" (flow speed equals wave speed) in previous one-dimensional studies. For further reductions in downstream pressure, flow rate decreases. Cross-sectional narrowing is significant but localized. When the ratio of downstream-to-upstream wall thickness is ${\le}$ 2 the area throat is located near the downstream end; as wall taper is increased to ${\ge}$ 3 the constriction moves to the upstream end of the tube. In the planar two-dimensional channel, area reduction and flow limitation are also observed when outlet pressure is decreased. In contrast to the axisymmetric case, however, the elastic wall in the two-dimensional channel forms a smooth concave surface with the area throat located near the mid-point of the elastic wall. Though flow rate reaches a maximum and then falls, the flow does not appear to be choked.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.5
• /
• pp.64-73
• /
• 1995

A numerical simulation of heat and fluid flow for predicting the effect of passage arrangement in automotive heat battery has been performed. The system is assumed to be a two-dimensional laminar flow and isothermal boundary is applied to the surface of the latent heat storage vessel. In the case of ideal heat battery the flow rate into each flow passage is evenly distributed. The various models are considered in the view of pressure drop and bulk temperature. The effects on the efficiency of the heat battery are examined by varying geometrical factors such as flow passage clearance, length of a inlet and outlet tank and the length of a latent heat storage vessel. The flow clearance is a very important -factor on the efficiency of a heat battery. As the flow passage clearance becomes narrow, the flow distribution becomes uniform and the bulk temperature increases, however the pressure drop is large. Therefore, optimal flow passage clearance has to be chosen. The present work can be used in optimizing heat battery efficiency.

• Proceedings of the Korea Multimedia Society Conference
• /
• 2002.05c
• /
• pp.286-289
• /
• 2002

뇌 혈관 영상은 2D로 되어있어 임상에서 뇌의 이상 유무와 질병의 진행 정도를 판별하는데 어려움이 있다. Volume Rendering은 2차원 데이터를 3차원 영상으로 재구성하여 오브젝트의 내부 모습을 3차원으로 볼 수 있게 해주는 장점이 있어 진단에 도움을 줄 수가 있다. MRA(Magnetic Resonance Angiography) 는 MRI(Magnetic Resonance Imaging)을 이용하여 Vascular Imaging 하는 기법이다. MRA 혈관 영상을 가시화하는 방법으로 MIP(Maximum Intensity Projection)를 이용하였다. 본 논문에서는 256×256 크기의 MRA영상 48장을 MIP 로 볼륨 랜더링하여 뇌 혈관 영상을 3차원으로 가시화 하였다.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.4 no.2
• /
• pp.57-61
• /
• 2008

During the period of retubing work for the licensing renewal, the fuel channels, calandria tubes and feeders of CANDU Reactors will be replaced, and calandria visual examination will be performed. This period is a unique opportunity to inspect the inside of the calandria. The visual inspection for the calandria vessel and its internals of Wolsong NPP is scheduled for confirming the calandria integrity. The first visual inspection for the calandria is planned in Pt. Lepreau led by AECL. The visual inspection for Wolsong NPP, led by NETEC(Nuclear Engineering & Technology Institute) of KHNP, will employ 3D laser scanner and 3D CAD Mock-up for the first time in the world, in addition to a conventional video camera. The inspection system is composed of a robot with the 3D laser scanner, a video camera and a hardness meter.

• Journal of Sensor Science and Technology
• /
• v.32 no.5
• /
• pp.300-306
• /
• 2023

A hull-cleaning robot sticks to the surface of a vessel and moves for efficient cleaning. Precise path planning and tracking using the current position is crucial. Many robots rely on the INS algorithm, but errors accumulate. To fix this, GPS, sonar, and USBL are used, though with limitations. Selecting suitable sensors for the surface operation and accurate positioning algorithm are vital. In this study, we developed a robot position estimation algorithm using the structure of a ship. Problems that arise when expanding the 2D position estimation algorithm used in existing wall structures to 3D were evaluated and methods for solving them were proposed. In addition, we aimed to improve performance by deriving singularities that exist in the robot path and proposing an error correction algorithm based on the singularities.