• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.5 no.1
• /
• pp.47-55
• /
• 1999

Applications of chitosan are related to molecular weight and degree of deacetylation(DOD) of chitosan completely. The molecular weight and DOD were greatly affected by the concentration of solution time and temperature. The degree of demineralization was not significantly different at $50^{\circ}C\;and\;70^{\circ}C$ after 30 minutes. Deproteinization decreased as process time increased. The nitrogen content was reached to 6.92% after 90 minute at $80^{\circ}C$, which is similar to theoretical nitrogen content of chitin. The DOD was 82.84% after 2 hours reaction and increased as the reaction time increased in the process. Viscosity and molecular weight are increased as recycling number of concentrated NaOH solution increased. Chemical, biological and physical properties of chitosan depend on the DOD and molecular size of the molecule. Tensile strength of the films from acetic acid solutions was between $28.9{\sim}33.6$ MPa and was generally higher than that of the films from lactic acid. Elongation of the films from lactic acid was between $97.0{\sim}109.7%$ and was generally higher than that of the films from the acetic acid. Water vapor permeability of the films prepared from lcetic acid solutions was between $1.9{\sim}2.3ng{\cdot}m/m^2{\cdot}s{\cdot}Pa$ and was generally higher than that of the films from the acetic acid.

• Food Science of Animal Resources
• /
• v.31 no.5
• /
• pp.731-740
• /
• 2011

This study was conducted to evaluate a quality comparison between Chuncheon Dakgalbi made from Korean native chickens (KNC) and that made from commercial broilers. Two Korean native chickens including Woorimatdag (KNCWoori) and Hanhyup3 (KNC-Hanhyup), and two commercial broilers including grades of 18 (Broiler-18) and 13 (Broiler-13) were slaughtered at 110, 70, 38, and 31 d of ages. Chuncheon dalkalbi was prepared by mixing/dipping the meat in chili pepper sauce; it was then packed with air-packaging (Air-P) and 30% $CO_2$-MAP (0% $O_2$/30% $CO_2$/70% $N_2$), and stored at $5^{\circ}C$ for 10 d. The results showed that the KNC group had a lower pH but a higher cooking loss compared with the broiler group (p<0.05). In a texture analysis, KNC-Woori had the highest shear force value among the breeds (p<0.05). For the fatty acid composition of the thigh, the KNC-Woori contained more total saturated acids, myristic acid, palmitic acid and stearic acid, but less total unsaturated fatty acids, linoleic acid and linolenic acid than other breeds (p<0.05). Also, the n6/n3 ratios of the KNC group (19.24 and 16.77) were higher than those of the broiler group (14.02 and 14.77) (p<0.05). The total acceptability scores of Dakgalbi made from the KNC group were decreased by sensory panelists. The Dakgalbi with 30% $CO_2$-MAP delayed the protein deterioration (Volatile basic nitrogen) and lipid oxidation during storage. However, no clear evidence was observed of $CO_2$-MAP on the effect of different chicken materials. It is suggested that 30% $CO_2$-MAP instead of Air-P is used for methods for Chuncheon Dakgalbi. Furthermore, it might be unfavorable to use Korean native chickens as raw material for Chuncheon Dakgalbi from a practical quality point of view.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.44 no.1
• /
• pp.40-50
• /
• 2016

A BIM, which is being applied actively to the construction and civil construction industries, is a technology that can maximize efficiency of various sectors from initial planning and design, construction, and maintenance, to demolition; however, it is in the introductory phase in the field of domestic landscaping. In order to introduce and promote BIM in the field of landscape design, this study developed a prototype of a library and template and analyzed the performance of trial application. For the development of a prototype, annotations and types were analyzed from floor plans of existing small parks, and components of landscape template were deduced. Based on this, play facilities, pergola, and benches were madeintofamily and templates, making automatic design possible. In addition, annotations and tags that are often used in landscape design were made, and a 3D view was materialized through visibility/graphic reassignment. As for tables and quantities, boundary stone table, mounding table, summary sheet of quantities, table of contents, and summary sheet of packaging quantities were grouped and connected with floor plans; regarding landscaping trees, classification criteria and name of trees that are suitable for domestic situations were applied. A landscape template was created to enable the library file format(rfa) that can be mounted on a building with BIM programs. As for problems that arose after the trial application of the prepared template, some CAD files could not be imported; also, while writing tables, the basis of calculation could not be made automatically. Regarding this, it is thought that functions of a BIM program and template need improvement.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.11a
• /
• pp.123-123
• /
• 2012

최근 연구되고 있는 TSV(Through Silicon Via) 기술은 Si 웨이퍼 상에 직접 전기적 연결 통로인 관통홀을 형성하는 방법으로 칩간 연결거리를 최소화 할 수 있으며, 부피의 감소, 연결부 단축에 따른 빠른 신호 전달을 가능하게 한다. 이러한 TSV 기술은 최근의 초경량화와 고집적화로 대표되는 전자제품의 요구를 만족시킬 수 있는 차세대 실장법으로 기대를 모으고 있다. 한편, 납땜 재료의 주 원료인 주석은 주로 반도체 소자의 제조, 반도체 칩과 기판의 접합 및 플립 칩 (Flip Chip) 제조시의 범프 형성 등 반도체용 배선재료에 널리 사용되고 있다. 최근에는 납의 유해성 때문에 대부분의 전자제품은 무연솔더를 이용하여 제조되고 있지만, 주석을 이용한 반도체 소자가 고밀도화, 고 용량화 및 미세피치(Fine Pitch)화 되고 있기 때문에, 반도체 칩의 근방에 배치된 주석으로부터 많은 알파 방사선이 방출되어 메모리 셀의 정보를 유실시키는 소프트 에러 (Soft Error)가 발생되는 위험이 많아지고 있다. 이로 인해, 반도체 소자 및 납땜 재료의 주 원료인 주석의 고순도화가 요구되고 있으며, 특히 알파 방사선의 방출이 낮은 로우알파솔더 (Low Alpha Solder)가 요구되고 있다. 이에 따라 본 연구는 4인치 실리콘 웨이퍼상에 직경 $60{\mu}m$, 깊이 $120{\mu}m$의 비아홀을 형성하고, 비아 홀 내에 기능 박막증착 및 전해도금을 이용하여 전도성 물질인 Cu를 충전한 후 직경 $80{\mu}m$의 로우알파 Sn-1.0Ag-0.5Cu 솔더를 접합 한 후, 접합부 신뢰성 평가를 수행을 위해 고속 전단시험을 실시하였다. 비아 홀 내 미세구조와 범프의 형상 및 전단시험 후 파괴모드의 분석은 FE-SEM (Field Emission Scanning Electron Microscope)을 이용하여 관찰하였다. 연구 결과 비아의 입구 막힘이나 보이드(Void)와 같은 결함 없이 Cu를 충전하였으며, 고속전단의 경우는 전단 속도가 증가할수록 취성파괴가 증가하는 경향을 보였다. 본 연구를 통하여 전해도금을 이용한 비아 홀 내 Cu의 고속 충전 및 로우알파 솔더 볼의 범프 형성이 가능하였으며, 이로 인한 전자제품의 소프트에러의 감소가 기대된다.

• Journal of Food Hygiene and Safety
• /
• v.31 no.4
• /
• pp.258-263
• /
• 2016

The risks of sanitary indicative bacteria, heavy metals and chlorinated derivatives in 94 cases of sanitary wet towels used in food services (39 from sanitary wet towel treatment business, 55 from food services) were assessed in the present study. Lead was detected in the range of N.D.~0.41 mg/kg (75 cases were not detected), N.D.~0.25 mg/kg of arsenic (93 cases were not detected), N.D.~0.01 mg/kg of cadmium (7 cases were lower than limit of quantitation; 87 cases were not detected), 0.003 mg/kg ~ 0.09 mg/kg of mercury. And chromium (VI) was not detected from all samples. The level of lead was the highest among the tested heavy metals, and the highest concentration of lead was 0.41 mg/kg. However, it was only 2.1% of legal limit (less than 20 mg/kg). The average moisture content of the samples was 61.9% (50.0% ~ 77.0%) and it showed no relevance to the detection of bacterial counts. Escherichia coli was not detected. Bacterial counts were detected 43 cases and among them, 24 cases were exceeded the legal limit. It was verified that the packaging conditions of sanitary wet towel (whether it is packed by a piece or not and sealed or not) are critical factors to cause the germ contamination and cross contamination in the wet towels. The chlorinated derivatives (chlorites and chlorates) were detected in 17 (19.3%) out of 88 cases. The results would be used as preliminary information to establish the programs of "Safety education for manufacturers and public policy of safety".

• Journal of the Korean Society of Radiology
• /
• v.8 no.7
• /
• pp.371-376
• /
• 2014

The process of flip-chip bump bonding, Au wire bonding and encapsulation were sucessfully developed and modularized. The CdTe sensor and ROIC were optimally jointed together at $150^{\circ}C$ and $270^{\circ}C$ respectively under24.5 N for 30s. To make SnAg bump on ROIC easy to be bonded, the higher bonding temperature was established than CdTe sensor's. In addition, the bonding pressure was lowered minimally because CdTe Sensor is easier to break than Si Sensor. CdTe multi-energy sensor module observed were no electrical failures in the joints using developed flip chip bump bonding and Au wire bonding process. As a result of measurement, shearing force was $2.45kgf/mm^2$ and, it is enough bonding force against threshold force, $2kgf/mm^2s$.

• Polymer(Korea)
• /
• v.32 no.1
• /
• pp.13-18
• /
• 2008

For the evaluation of brominated flame retardants included in polymeric electronic devices, we investigated the extraction methods and solvent systems for four different types of polymers of PC (polycarbonate), PP (polyropylene), PET (poly(ethylene terephthalate)) and PBT (poly(butylene terephthalate)) using different solvent systems of hexane/acetone, THF, toluene, and THF/toluene. In order to compare the extraction efficiency of different methods and solvent systems, the deca-BDE (decabromo diphenyl ether) flame retardant was included in PC, PP, PET and PBT systems and subsequently extracted by soxhlet, ultrasonic, accelerated solvent, microwave and supercritical fluid extraction methods. The amount of the extracted flame retardant was monitored to evaluate the extraction efficiency. The ultrasonic extraction method was found not to be acceptable as an extraction method for the polymer systems mainly due to a low salvation efficiency of the organic solvents. Soxhlet, accelerated solvent and microwave extraction methods exhibited over 80% of extraction efficiency for toluene. The supercritical fluid extraction method, which has been used as an extraction method for flame retardants in polymers, showed the extraction efficiencies of ca. 100% for PC and PP in the optimal extraction conditions of $60^{\circ}C$ and 120 bar.

• The Korean Journal of Food And Nutrition
• /
• v.24 no.4
• /
• pp.551-558
• /
• 2011

This present study was performed to analyze the efficiency and volatility of a porous film containing $Chamaecyparis$ $obtusa$ extract as a method to effectively package food compounds. Phytoncide was contacted the state of gas and showed effective antimicrobial properties. Limonene can be distilled without decomposition as a relatively stable terpene and was one of the extract components. $Chamaecyparis$ $obtusa$ essential oil. The optimal solvent composition was a ratio 5:20:0.3 of T-500:ethanol:hardener to effectively manufacture film containing phytoncide essential oil and the minimum antibacterial concentration was 2%. The films were made under different conditions(A-50LF1, A-25SF2, B-50SF1, C-50LF1, C-25SF2 and D-50SF1) containing phytoncide and the amounts of limonene inside the 1-L reaction chamber depending on storage were measured by gas chromatography-mass selective detention. The results showed that the 25SF2(width, 25 mm; length, 20 cm) revealed more amount of limonene compared with 50LF1(width 50 mm, length 20 cm). We confirmed that the gas emission amount showed a better layer on the film side than on the internal film. An effect of film thickness on phytoncide emissions was observed in that the amounts was less than the expectation for a thicker film at the beginning time, but the emitting amounts increased with increasing storage periods. In the storage testing of various films at $35^{\circ}C$ and 70% humidity for 14 days, 25SF2 showed longer preservation compared with that of 50LF in the case of bread. $C.$ $obtusa$ essential oil is a useful fresh ingredients, hence, analysis of limonene emission kinetics from various film was helpful to develop films with an optimal antimicrobial effect, and will allow application of such films in food packaging systems.

• Journal of Food Hygiene and Safety
• /
• v.29 no.3
• /
• pp.181-188
• /
• 2014

The objective of this study was to analyze the microbiological hazards of Astragalus membranaceus Bunge on the post-harvest processing. Samples from processing equipments (cleaner, water, cart, table, tray and packaging machine), personal hygiene (hand) and harvested crops (before washing, after washing, after sorting, and after drying) were collected from four farms (A, B, C, and D) located in Chungchengbuk-do, Korea. The samples were analyzed for sanitary indication bacteria and pathogenic bacteria. First, total aerobic bacteria and coliform in processing facilities were detected at the levels of 0.93~4.86 and 0.33~2.28 log CFU/$100cm^2$ and/mL respectively. In particular, microbial contamination in hand (5.43~6.11 and 2.52~4.12 log CFU/Hand) showed higher than processing equipments. Among the pathogenic bacteria, Bacillus cereus was detected at the levels of 0.33~2.41 log CFU/$100cm^2$, 1.48~3.27 log CFU/Hand and 0.67~3.65 log CFU/g in equipments, hands, and plants and Staphylococcus aureus were detected in cleaner, table, hand and harvested crops (before washing and after sorting) by qualitative test. Escherichia coli O157:H7, Listeria monocytogenes, and Salmonella spp. were not detected. These results indicated that personal hygiene and processing equipments should be managed to reduce the microbial contamination of A. membranaceus Bunge. Therefore, management system such as good agricultural practices (GAP) criteria is needed for hygienic agricultural products.

• Proceedings of the Korean Reliability Society Conference
• /
• 2001.06a
• /
• pp.277-278
• /
• 2001

The successful operation of a product In service depends upon the effective provision of logistic support in order to achieve and maintain the required levels of performance and customer satisfaction. Logistic support encompasses the activities and facilities required to maintain a product (hardware and software) in service. Logistic support covers maintenance, manpower and personnel, training, spares, technical documentation and packaging handling, storage and transportation and support facilities.The cost of logistic support is often a major contributor to the Life Cycle Cost (LCC) of a product and increasingly customers are making purchase decisions based on lifecycle cost rather than initial purchase price alone. Logistic support considerations can therefore have a major impact on product sales by ensuring that the product can be easily maintained at a reasonable cost and that all the necessary facilities have been provided to fully support the product in the field so that it meets the required availability. Quantification of support costs allows the manufacturer to estimate the support cost elements and evaluate possible warranty costs. This reduces risk and allows support costs to be set at competitive rates.Integrated Logistic Support (ILS) is a management method by which all the logistic support services required by a customer can be brought together in a structured way and In harmony with a product. In essence the application of ILS:- causes logistic support considerations to be integrated into product design;- develops logistic support arrangements that are consistently related to the design and to each other;- provides the necessary logistic support at the beginning and during customer use at optimum cost.The method by which ILS achieves much of the above is through the application of Logistic Support Analysis (LSA). This is a series of support analysis tasks that are performed throughout the design process in order to ensure that the product can be supported efficiently In accordance with the requirements of the customer.The successful application of ILS will result in a number of customer and supplier benefits. These should include some or all of the following:- greater product uptime;- fewer product modifications due to supportability deficiencies and hence less supplier rework;- better adherence to production schedules in process plants through reduced maintenance, better support;- lower supplier product costs;- Bower customer support costs;- better visibility of support costs;- reduced product LCC;- a better and more saleable product;- Improved safety;- increased overall customer satisfaction;- increased product purchases;- potential for purchase or upgrade of the product sooner through customer savings on support of current product.ILS should be an integral part of the total management process with an on-going improvement activity using monitoring of achieved performance to tailor existing support and influence future design activities. For many years, ILS was predominantly applied to military procurement, primarily using standards generated by the US Government Department of Defense (DoD). The military standards refer to specialized government infrastructures and are too complex for commercial application. The methods and benefits of ILS, however, have potential for much wider application in commercial and civilian use. The concept of ILS is simple and depends on a structured procedure that assures that logistic aspects are fully considered throughout the design and development phases of a product, in close cooperation with the designers. The ability to effectively support the product is given equal weight to performance and is fully considered in relation to its cost.The application of ILS provides improvements in availability, maintenance support and longterm 3ogistic cost savings. Logistic costs are significant through the life of a system and can often amount to many times the initial purchase cost of the system.This study provides guidance on the minimum activities necessary to Implement effective ILS for a wide range of commercial suppliers. The guide supplements IEC60106-4, Guide on maintainability of equipment Part 4: Section Eight maintenance and maintenance support planning, which emphasizes the maintenance aspects of the support requirements and refers to other existing standards where appropriate. The use of Reliability and Maintainability studies is also mentioned in this study, as R&M is an important interface area to ILS.