• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.30 no.2
• /
• pp.71-77
• /
• 1994

A serious of study is carried out to practical use of the three-slot cambered otter board improved by the authors. As the first step, we designed main plates, slots and accessories, such as holding plate, fan-shaped towing plate, normans, center ring, etc. Standing on this design, we made the simple cambered and three-slot cambered model otter board with accessories in a linear scale 6:1. and carried out model test to examine the efficiency of these boards. The obtained results can be summarized as follows: 1. On the simple cambered board with accessories, the values of the maximum shear coefficient($C _{LX}$ ). drag coefficient(($C _{D}$) and hydrodynamic efficiency($C _{L}$/$C _{D}$ ) are 1.39, 0.56, 2.48 at $22^{\circ}$ of the angle of stall respectively. 2. On the three-slot cambered board with accessories, $C _{LX}$/$C _{D}$ and $C _{I}$/$C _{D}$ are 1.67, 0.92, 1.82 at $32^{\circ}$ of the angle of stall respectively. 3.$C _{LX}$ of board with accessories is smaller 10~12% than that of only the main plate, and the angle of stall is almost same. 4. $C _{LX}$ and the angle of stall of the three-slot cambered board with accessories are greater 20% and $10^{\circ}$ than that of the simple cambered board respectively.

• Ocean Systems Engineering
• /
• v.1 no.1
• /
• pp.73-93
• /
• 2011

Large deck openings of ultra large container ships reduce their torsional stiffness considerably and hydroelastic analysis for reliable structural design becomes an imperative. In the early design stage the beam model coupled with 3D hydrodynamic model is a rational choice. The modal superposition method is ordinary used for solving this complex problem. The advanced thin-walled girder theory, with shear influence on both bending and torsion, is applied for calculation of dry natural modes. It is shown that relatively short engine room structure of large container ships behaves as the open hold structure with increased torsional stiffness due to deck effect. Warping discontinuity at the joint of the closed and open segments is compensated by induced distortion. The effective torsional stiffness parameters based on an energy balance approach are determined. Estimation of distortion of transverse bulkheads, as a result of torsion and warping, is given. The procedure is illustrated in the case of a ship-like pontoon and checked by 3D FEM analysis. The obtained results encourage incorporation of the modified beam model of the short engine room structure in general beam model of ship hull for the need of hydroelastic analysis, where only the first few natural modes are of interest.

• Ocean Systems Engineering
• /
• v.7 no.4
• /
• pp.435-460
• /
• 2017

The main objective of this study is to investigate the turning and zig-zag maneuvering performance of the well-known naval surface combatant DTMB (David Taylor Model Basin) 5415 hull with URANS (Unsteady Reynolds-averaged Navier-Stokes) method. Numerical simulations of static drift tests have been performed by a commercial RANS solver based on a finite volume method (FVM) in an unsteady manner. The fluid flow is considered as 3-D, incompressible and fully turbulent. Hydrodynamic analyses have been carried out for a fixed Froude number 0.28. During the analyses, the free surface effects have been taken into account using VOF (Volume of Fluid) method and the hull is considered as fixed. First, the code has been validated with the available experimental data in literature. After validation, static drift, static rudder and drift and rudder tests have been simulated. The forces and moments acting on the hull have been computed with URANS approach. Numerical results have been applied to determine the hydrodynamic maneuvering coefficients, such as, velocity terms and rudder terms. The acceleration, angular velocity and cross-coupled terms have been taken from the available experimental data. A computer program has been developed to apply a fast maneuvering simulation technique. Abkowitz's non-linear mathematical model has been used to calculate the forces and moment acting on the hull during the maneuvering motion. Euler method on the other hand has been applied to solve the simultaneous differential equations. Turning and zig-zag maneuvering simulations have been carried out and the maneuvering characteristics have been determined and the numerical simulation results have been compared with the available data in literature. In addition, viscous effects have been investigated using Eulerian approach for several static drift cases.

• Journal of Korea Water Resources Association
• /
• v.44 no.6
• /
• pp.429-438
• /
• 2011

In order to simulate a free surface flow in a trench channel, a three-dimensional incompressible unsteady Reynolds-averaged Navier-Stokes (RANS) equations are closed with the ${\kappa}-{\epsilon}$ model. The artificial compressibility (AC) method is used. Because the pressure fields can be coupled directly with the velocity fields, the incompressible Navier-Stokes (INS) equations can be solved for the unknown variables such as velocity components and pressure. The governing equations are discretized in a conservation form using a second order accurate finite volume method on non-staggered grids. In order to prevent the oscillatory behavior of computed solutions known as odd-even decoupling, an artificial dissipation using the flux-difference splitting upwind scheme is applied. To enhance the efficiency and robustness of the numerical algorithm, the implicit method of the Beam and Warming method is employed. The treatment of the free surface, so-called interface-tracking method, is proposed using the free surface evolution equation and the kinematic free surface boundary conditions at the free surface instead of the dynamic free surface boundary condition. AC method in this paper can be applied only to the hydrodynamic pressure using the decomposition into hydrostatic pressure and hydrodynamic pressure components. In this study, the boundary-fitted grids are used and advanced each time the free surface moved. The accuracy of our RANS solver is compared with the laboratory experimental and numerical data for a fully turbulent shallow-water trench flow. The algorithm yields practically identical velocity profiles that are in good overall agreement with the laboratory experimental measurement for the turbulent flow.

• Computational Structural Engineering
• /
• v.8 no.3
• /
• pp.67-74
• /
• 1995

This study develops 2-D analysis method of a base-isolated pool structure, and verifies the method through shaking table test using a scaled model. A wall of the pool structure is modeled as lumped mass, and added mass of the fluid is imposed on the nodes of the structure to consider the hydrodynamic effect of contained fluid. The equation of motion of base-isolated pool structure is obtained by coupling of two equations for superstructure composed of wall and fluid, and for bottom slab and isolator. The scaled model for shaking table test is made with transparent acryle, and 4-high damping laminated rubber bearings are used. The responses of the scaled model by the test are generally good agreement with those by the analysis. It is shown that 2-D analysis method gives somewhat conservative results.

• Journal of Korean Society of Water and Wastewater
• /
• v.23 no.1
• /
• pp.15-22
• /
• 2009

This study reports the serial use of a 3-D hydrodynamic model, EFDC-Hydro and a dynamic water quality model WASP7.2 that are maintained by USEPA. The 48 km section of the Geum River downstream between Daechung Dam and Gongju was selected as a sample study site. Topographical information was used to accurately represent morphology of the study site and boundary conditions were derived from governmental databases including WAMIS by Ministry of Land and Ocean and WEIS by Ministry of Environment. EFDC-Hydro was successfully calibrated for observed water level and WASP was calibrated using monthly observed water quality data obtained from the above sources. It was found that the current water quality target of BOD for the Geum River-H point could not be met on monthly basis though every other tributary of the area would meet its own water quality target as assigned in Korean TMDL. This study proposed the new target BOD water quality for the Gabcheon and Mihocheon as 4.3 and 3.6 mg/l, respectively so that the Geum River-H point can meet the target. When Sejong City is constructed, it is estimated that effluent discharge limit of BOD must be less than 4.5 mg/l to meet water quality of the point. This study shows that it is possible to carry out more precise modeling considering both water movement and water kinetics by using EFDC and WASP simultaneously.

• Journal of Environmental Impact Assessment
• /
• v.22 no.4
• /
• pp.329-343
• /
• 2013

According to previous studies, the increased air temperature can lead to change of thermal stratification structure of lakes and reservoirs. The changed thermal stratification may result in alteration of materials and energy flow. The objective of this study was to predict the effect of climate change on the water temperature and stratification structure of Daecheong Reservoir, located in Geum River basin of Korea, using a three-dimensional(3D) hydrodynamic model(ELCOM). A long-term(100 years) weather data set provided by the National Institute of Meteorological Research(NIMR) was used for forcing the 3D model. The model was applied to two different hydrological conditions, dry year(2001) and normal year(2004). It means that the effect of air temperature increase was only considered. Simulation results showed that the surface water temperature of the reservoir tend to increase in the future, and the establishment of thermal stratification can occur earlier and prolonged longer. As a result of heat flux analysis, the evaporative heat loss can increase in the future than now and before. However, the convective heat loss and net long wave radiation from water surface decreased due to increased air temperature.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2004.05b
• /
• pp.453-457
• /
• 2004

본 연구에서는 WES의 표준 월류형 여수로에 대한 동수역학적인 흐름거동을 FLOW-3D 모형을 이용하여 해석하였다. 월류수두에 따른 월류유량, 월류흐름의 수면곡선, 여수로 표면에서의 압력분포와 같은 모의결과는 WES의 실험자료와 잘 일치하였다. 그리고 월류수두가 여수로 설계수두의 1.33배인 경우의 유속과 압력의 연직분포를 검토하였다. 검토결과, 웨어마루를 통과하면서 저층의 유속이 먼저 가속되며 점차 하류로 이동하면서 수표면의 유속이 가속되어 거의 균일한 유속분포를 보였으며, 압력의 연직분포는 웨어마루 상류에서는 수표면에서 내기압을 보이고 점차 수심이 길어짐에 따라 정수압분포와 유사한 분포를 보이나, 여수로 표면에 접근함에 따라 급격하게 압력이 감소하면서 부압이 발생하였다. 웨어마루 하류에서는 여수로 표면에서의 압력이 점차 대기압으로 접근함에 따라, 거의 전 수심에 걸쳐 대기압과 유사한 분포를 보였다.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• v.5 no.2
• /
• pp.71-99
• /
• 2001

The model and analytical method for solving the problem of coupled fluid flow in the reservoir/well system is presented. The 3-D drainage area is composed of three connected media: the tubing, the annuli as a super conducting collector, and the reservoir itself. To couple these three types of fluid flows a non-overlapping Dirichlet-Neumann domain decomposition method is developed. The method allows us to apply an analytical hybrid simulator for accurate evaluation of the impact of main geometrical and hydrodynamic parameters of the 3-D system on the pressure drop along the horizontal well and its production index.

• Journal of Ocean Engineering and Technology
• /
• v.33 no.6
• /
• pp.581-589
• /
• 2019

In order to understand the characteristics of beach deformation, in this study, numerical simulations were conducted using a 3-D hydro-morphodynamic model (HYMO-WASS-3D) to analyze the characteristics of beach deformation due to the coastal groundwater levels. HYMO-WASS-3D directly analyzed the nonlinear interaction between the hydrodynamic and morphodynamic processes in the coastal area. The simulation results of HYMO-WASS-3D showed good agreement with the experimental results on the changes in the profile of the beach in the surf and swash zones. Then, numerical simulations were conducted to examine the characteristics of beach deformation due to the variation of the level of the coastal groundwater. As a result, the beach profiles were examined in relation to the wave breaking in the surf zone and the wave uprush and backwash in the swash zone due to the differences in the water levels. This paper also discussed the temporal and spatial distributions of the velocities, vorticities, and suspended sediments in the surf and swash zones with various levels of the coastal groundwater.