• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.8
• /
• pp.844-853
• /
• 2008

This paper describes the design of a FEM(Front End Module) having power detection function for mobile handset application. The designed FEM consists of a MMIC(Monolithic Microwave Integrated Circuits) power amplifier chip, SAW Tx filter and duplexer, diode power detector and stripline matching circuit. An LTCC(Low Temperature Co-fired Ceramics) technology is adopted for miniaturized FEM. The frequency band is $824{\sim}869$ MHz which is the uplink Tx band of the CDMA mobile system. The size of designed FEM is $7.0{\times}5.5{\times}1.5\;mm^3$, which is an ultra-small size even though the power detector circuit is included. All sub-components of FEM have been developed and measured in advance before being integrated into FEM. The measured output power and gain are 27 dBm and 27 dB, respectively. In addition, the measured ACPR characteristics are 46.59 dBc and 55.5 dBc at 885 kHz and 1.98 MHz offset, respectively.

• Journal of Electrical Engineering and Technology
• /
• v.6 no.3
• /
• pp.369-374
• /
• 2011

An induction motor operated with high voltage source generally generates high current in starting mode and has a long transient time after being started. This large and sustaining starting current causes the end windings of the stator to have excessive electromagnetic force. This force is the source of vibration and has a negative and serious influence on the insulation of end windings. Therefore, designing the end winding part with an appropriate support system is needed. To design the support ring enclosing the end windings, we analyze the distribution of electromagnetic force on the end windings by applying the Biot-Savart's law and the 3D finite element method (FEM), and comparing two simulation methods. Finally, we verify the safety of the support structure of the end winding part using stress analysis, which is analyzed with the electromagnetic forces from the 3D FEM simulation.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.835-837
• /
• 2002

This paper presents a shape optimization algorithm of electromagnetic devices using the design sensitivity analysis with FEM. The design sensitivity and adjoint variable formulas are derived for the 3D FEM with edge element. This algorithm is applied to 3D electro-magnet pole shape optimization problem to make a uniform flux density at the target region.

• Proceedings of the KSR Conference
• /
• 2002.05a
• /
• pp.171-176
• /
• 2002

There are many railway structures which were designed without conidering aseismic capacity. In special, masonry structures constructed long time ago should be reviewed about their resistance to earthquake. In this paper, technique to evaluate the capacity of masonry railway bridge is tried to develop by means of FEM analysis. In general FEM analysis program, 3-D solid element is used for masonry structures and response spectrum analysis procedure is tried. In addition, 3-D solid element has material properties equivalent to mortar-brick composite body. Used FEM program is ABAQUS-CAE.

• Transactions of Materials Processing
• /
• v.19 no.2
• /
• pp.101-106
• /
• 2010

CB100 is one of the channel type products in the steel beam. In this study, rolling process of CB100 is analyzed by 3D FEM simulation and rolling process. FEM simulation result is compared with rolling process data. Also the intermediate & finishing roll stress analysis is carried out and the suitability of the roll through roll stress resultant analysis is evaluated. In order to decrease the roll stress, new pass schedule is developed for stable load balance between intermediate and finishing rolling stand. Therefore new rolling pass schedule is verified by the analysis results of rolling process and roll stress. By the analysis results, the credibility of rolling process analysis was obtained and it was determined that the possibility of roll damage between intermediate and finishing mill was high. So the new pass schedule was developed. Through the result of rolling process and roll stress analysis, it was obtained that the reduction of roll stress and stable load balance.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.401.2-401
• /
• 2002

An unconstrained tuning fork with a 3-D model has been numerically analyzed by Finite Element Method (FEM) and Boundary Element Method (BEM). The first three natural frequencies were calculated by the FEM modal analysis. Then the change of the modal frequencies was examined with the variation of the tuning fork length and width. (omitted)

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.904-905
• /
• 2011

본 논문에서는 기존의 EPS(Electric Power Steering) 시스템에 IPMSM을 적용하고 속도 및 위치를 검출하기 위하여 Magnetic Position Sensor를 사용하였다. 이�� Magnetic Position Sensor의 신호는 정현파의 출력을 갖지만 고조파의 성분으로 인하여서 파형이 왜곡되고 이러한 파형의 왜곡으로 인해 위치 검출의 오차를 갖게 된다. 본 논문에서는 이러한 오차를 줄이기 위하여 다구찌 기법과 3차원 유한요소법(3D FEM)을 사용하여 고조파를 저감시킬 수 있도록 여러 변수를 변화하여서 최적의 설계를 통하여 실제 실제 센서 출력과 비교하여 자동차 산업 전반에 기여 하고자 한다.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.153-155
• /
• 1994

Electric machines such as motors which have moving parts are desgined for producing mechanical force or torque. The accurate calculation of electromagnetic force and torque is important in the design these machines, Electromagnetic force calculation method using the results of Finite Element Method(FEM) has been presented variously in 2-D problems. Typically the Maxwell's Stress Tensor method and the method of virtual work are used. In the problems including current source, magnetic vector potentials(MVP) have mostly been used as an unknown variables for field analysis by numerical method; e, g. FEM. This paper, thus, introduces both methods using MVP in 3-D case. To verify the usefulness of presented methods, a solenoid model is chosen and analyzed by 3-D and axisymmetrical FEM. In each case, the calculated force are tabulated for several mesh schemes.

• Proceedings of the KIEE Conference
• /
• 2000.11b
• /
• pp.238-240
• /
• 2000

We designed the prototype of electromagnetic wobble motor which could be applied to ultrasonic catheter in the before study. So, In this paper we perform 3D FEM of the designed prototype model with the computer analysis tool(Magnet 6.4). Therefore we prove the characteristics and theorems of the wobble motor with 3D FEM.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.711-713
• /
• 2001

MCCB(Molded Case Circuit Breakers) is a multi-function safety device which, unlike other forms of protection, combines many protection features in a single unit. This paper is the analysis of magnetic repulsion forces with the breaking current 11.28kA, 22.5kA, 38.9kA and 45kA.