• Journal of Conservation Science
• /
• v.36 no.5
• /
• pp.306-314
• /
• 2020

The use of synthetic resins in ceramic restoration poses several challenges, including aging and potential damage to artifacts, which has raised the need to investigate new materials and restoration methods. This study set out to incorporate full color 3D printing into the 3D digital technology-based restoration method, an emerging approach currently being researched, and to print out missing parts with color information. After examining material physical properties with an experiment, the investigator printed out missing parts from a white porcelain vessel and grayish-blue-powdered celadon plate and compared them in chromaticity and brilliance. The experimental results show that the outputs had comparable tensile strength to the original restoration materials, whereas the recorded compressive strength was approximately 1.4~2 times higher than that of the original restoration materials. According to the NIST table of color difference values, the white porcelain vessel was visible at ΔE^*ab 1.55, and the grayish-blue-powdered celadon plate was perceivable at 3.34. Even though it was impossible to express the colors accurately owing to printer limitations, this non-contact approach reduced the possibility of damage to the minimum. In conclusion, it can be applied to objects with a high chance of damage or generate display effects through purposeful color differentiation in missing parts.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.26 no.4
• /
• pp.241-246
• /
• 2013

From the numerical results of density-based topology design optimization, a CAD geometric model is constructed and fabricated using 3D printer to experimentally validate the optimal design. In the process of topology design optimization, we often experience checkerboard phenomenon and complicated branches, which could result in the manufacturing difficulty of the obtained optimal design. Sensitivity filtering and morphology methods are used to resolve the aforementioned issues. Identical volume fraction is used in both numerical and experimental models for precise validation. Through the experimental comparison of stiffness in various designs including the optimal design, it turns out that the optimal design has the highest stiffness and the experimental result of compliance matches very well with the numerical one.

• Journal of the Korean Society of Radiology
• /
• v.12 no.1
• /
• pp.71-78
• /
• 2018

In this study, human mimic phantoms outputted by three-dimensional (3D) printing technology are reported. Polylactic acid and a personal 3D printer - fused deposition modeling (FDM) - are used as the main material and the printing device. The output of human mimic phantoms performed in the following order: modeling, slicing and G-code conversion, output variable setting, 3D output, and post-processing. The students' learning satisfaction (anatomical awareness, study interest) was measured on 5-point Likert scale. After that, Twenty of those phantoms were outputted. The total output took 11,691 minutes (194 hours 85 minutes) and the average output took 584.55 minutes (9 hours 7 minutes). The filament used for the experiment was 2,390.2 g, and the average use of the filament was 119.51 g. The learning satisfaction of anatomical awareness was 4.6 points on the average and the interest of the class was on average 4.5 points. It is expecting that 3D printing technology can enhance the learning effect of imaging anatomy education.

• The Journal of Korean Society for Radiation Therapy
• /
• v.27 no.1
• /
• pp.61-71
• /
• 2015

Purpose : 3D Printers are used to create three-dimensional models based on blueprints. Based on this characteristic, it is feasible to develop a bolus that can minimize the air gap between skin and bolus in radiotherapy. This study aims to compare and analyze air gap and target dose at the branded 1 cm bolus with the developed customized bolus using 3D printers. Materials and Methods : RANDO phantom with a protruded tumor was used to procure images using CT simulator. CT DICOM file was transferred into the STL file, equivalent to 3D printers. Using this, customized bolus molding box (maintaining the 1 cm width) was created by processing 3D printers, and paraffin was melted to develop the customized bolus. The air gap of customized bolus and the branded 1 cm bolus was checked, and the differences in air gap was used to compare $D_{max}$, $D_{min}$, $D_{mean}$, $D_{95%}$ and $V_{95%}$ in treatment plan through Eclipse. Results : Customized bolus production period took about 3 days. The total volume of air gap was average $3.9cm^3$ at the customized bolus. And it was average $29.6cm^3$ at the branded 1 cm bolus. The customized bolus developed by the 3D printer was more useful in minimizing the air gap than the branded 1 cm bolus. In the 6 MV photon, at the customized bolus, $D_{max}$, $D_{min}$, $D_{mean}$, $D_{95%}$, $V_{95%}$ of GTV were 102.8%, 88.1%, 99.1%, 95.0%, 94.4% and the $D_{max}$, $D_{min}$, $D_{mean}$, $D_{95%}$, $V_{95%}$ of branded 1cm bolus were 101.4%, 92.0%, 98.2%, 95.2%, 95.7%, respectively. In the proton, at the customized bolus, $D_{max}$, $D_{min}$, $D_{mean}$, $D_{95%}$, $V_{95%}$ of GTV were 104.1%, 84.0%, 101.2%, 95.1%, 99.8% and the $D_{max}$, $D_{min}$, $D_{mean}$, $D_{95%}$, $V_{95%}$ of branded 1cm bolus were 104.8%, 87.9%, 101.5%, 94.9%, 99.9%, respectively. Thus, in treatment plan, there was no significant difference between the customized bolus and 1 cm bolus. However, the normal tissue nearby the GTV showed relatively lower radiation dose. Conclusion : The customized bolus developed by 3D printers was effective in minimizing the air gap, especially when it is used against the treatment area with irregular surface. However, the air gap between branded bolus and skin was not enough to cause a change in target dose. On the other hand, in the chest wall could confirm that dose decrease for small the air gap. Customized bolus production period took about 3 days and the development cost was quite expensive. Therefore, the commercialization of customized bolus developed by 3D printers requires low-cost 3D printer materials, adequate for the use of bolus.

• Journal of radiological science and technology
• /
• v.38 no.4
• /
• pp.389-394
• /
• 2015

There is a progressive development in the medical imaging technology, especially of descriptive capability for anatomical structure of human body thanks to advancement of information technology and medical devices. But however maintenance of correct posture is essential for the medical imaging checkup on the shoulder joint requiring rotation of the upper limb due to the complexity of human body. In the cases of MRI examination, long duration and fixed posture are critical, as failure to comply with them leads to minimal possibility of reproducibility only with the efforts of the examiner and will of the patient. Thus, this study aimed to develop an auxiliary device that enables rotation of the upper limb as well as fixing it at quantitative angles for medical imaging examination capable of providing diagnostic values. An auxiliary device has been developed based on the results of precedent studies, by designing a 3D model with the CATIA software, an engineering application, and producing it with the 3D printer. The printer is Objet350 Connex from Stratasys, and acrylonitrile- butadiene-styrene(ABS) is used as the material of the device. Dimensions are $120{\times}150{\times}190mm$, with the inner diameter of the handle being 125.9 mm. The auxiliary device has 4 components including the body (outside), handle (inside), fixture terminal and the connection part. The body and handle have the gap of 2.1 mm for smooth rotation, while the 360 degree of scales have been etched on the handle so that the angle required for observation may be recorded per patient for traceability and dual examination.

• Journal of the Korean Society of Radiology
• /
• v.12 no.7
• /
• pp.879-886
• /
• 2018

A 3-dimensional (D) printer is a device capable of outputting a three-dimensional solid object based on data modeled in a computer. These features are utilized in the bone model X - ray phantom production etc using CT data by fusing with the radiation science field. A bone model phantom was made using data obtained by CT scan of an existing Pelvis phantom, using PLA, Wood, XT-CF20, Glow fill, Steel filaments which are materials of Fused Filament Fabrication (FFF) 3D printer.Measure Hounsfield Unit (HU) with images obtained by CT scan of the existing Pelvis phantom and five material phantoms made with 3D printer under the same conditions,SI and SNR were measured using a diagnostic X-ray generator, and each phantom was compared and analyzed.As a result, the X - ray phantom in the X - ray examination condition of the limb was found to be most suitable for the glow fill filament.The characteristics of the filament can be known to the base of this research and the practicality of X - ray phantom fabrication was confirmed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.1
• /
• pp.65-71
• /
• 2016

In recent years, 3D printing has received increasing attention due to releases of low-cost 3D printers based on open-source platform. 3D printing is expected to reduce the barrier to entry in the traditional manufacturing processes by increasing flexibility and creating an advantage to manufacture customized products at low costs. In this study, a unique eyeglass frame was designed to have a snake shape, which has an asymmetric geometry unlike traditional frames. The eyeglass frame was designed in a customized manner by reflecting dimensional characteristics of a customer's face. Finite element analysis was performed to investigate the structural safety of the 3D printed frames during the assembly process. The analysis also considered the effect of anisotropic material properties as determined by tensile tests. The eyeglass frame was then printed using the customized sizes and the best building process. The eyeglass frame was successfully assembled with lenses and without structural failure during its assembly procedure.

• Journal of IKEEE
• /
• v.23 no.4
• /
• pp.1250-1256
• /
• 2019

Although one can easily generate real-world 3D mesh data using a 3D printer or a depth camera, the generated data inevitably includes unnecessary noise. Therefore, mesh denoising is essential to obtain intact 3D mesh data. However, conventional mathematical denoising methods require preprocessing and often eliminate some important features of the 3D mesh. To address this problem, this paper proposes a deep learning based 3D mesh denoising method. Specifically, we propose a convolution-based autoencoder model consisting of an encoder and a decoder. The convolution operation applied to the mesh data performs denoising considering the relationship between each vertex constituting the mesh data and the surrounding vertices. When the convolution is completed, a sampling operation is performed to improve the learning speed. Experimental results show that the proposed autoencoder model produces faster and higher quality denoised data than the conventional methods.

• Journal of Korea Multimedia Society
• /
• v.4 no.4
• /
• pp.316-323
• /
• 2001

Gamut mapping is a technique that acts on cross-media color reproduction to transform a color between devices for the purpose of enhancing the appearance or preserving the appearance of an image. Gamut mapping essentially produces color conversion error which depends on the gamut mapping method, source and destination devices, and sample points for gamut modeling. For color space conversion between monitor colors and printer colors, empirical representation using sample measurements is currently widely utilized. Color samples are uniformly selected in the device space such as CMY or RGB, represented as color patches, and then measured. However, in the case of printer, these color samples are not evenly distributed inside the printer gamut and the color conversion error is increased. Accordingly, this paper introduces a equally distributed color sampling method in CIELAB space, a device- independent color space, to reduce color conversion error, and the performance is analyzed via color space conversion experiments using three-dimensional interpolation.

• Journal of Korea Multimedia Society
• /
• v.19 no.8
• /
• pp.1619-1625
• /
• 2016

Recently, as the public interests about the 3D printing technology are increased, various kinds of 3D printers are being released. But, they are limited to use because they cannot fabricate an object which is larger than the printer's printing volume. To relieve this problem, we propose an interactive 3D mesh editing system for 3D printing the object that is larger than the printing volume. The proposed 3D editing system divides the input 3D mesh using the user's line drawings defining cutting planes and it attaches various connectors. The output meshes are guaranteed to fabricate without post-processing. The printed parts can be assembled using the connectors. Our proposed system has an advantage that it can be used easily by non-professional 3D printer users.