• Nuclear Engineering and Technology
• /
• 제51권5호
• /
• pp.1417-1427
• /
• 2019

In this study, we evaluated the performance of a commercial pixelated cadmium zinc telluride (CZT) detector for spectroscopy and identified its feasibility as a Compton camera for radiation monitoring in a nuclear power plant. The detection system consisted of a $20mm{\times}20mm{\times}5mm$ CZT crystal with $8{\times}8$ pixelated anodes and a common cathode, in addition to an application specific integrated circuit. The performance of the various radioisotopes $^{57}Co$, $^{133}Ba$, $^{22}Na$, and $^{137}Cs$ was evaluated. In general, the amplitude of the induced signal in a CZT crystal depends on the interaction position and material non-uniformity. To minimize this dependency, a drift time correction was applied. The depth of each interaction was calculated by the drift time and the positional dependency of the signal amplitude was corrected based on the depth information. After the correction, the Compton regions of each spectrum were reduced, and energy resolutions of 122 keV, 356 keV, 511 keV, and 662 keV peaks were improved from 13.59%, 9.56%, 6.08%, and 5%-4.61%, 2.94%, 2.08%, and 2.2%, respectively. For the Compton imaging, simulations and experiments using one $^{137}Cs$ source with various angular positions and two $^{137}Cs$ sources were performed. Individual and multiple sources of $^{133}Ba$, $^{22}Na$, and $^{137}Cs$ were also measured. The images were successfully reconstructed by weighted list-mode maximum likelihood expectation maximization method. The angular resolutions and intrinsic efficiency of the $^{137}Cs$ experiments were approximately $7^{\circ}-9^{\circ}$ and $5{\times}10^{-4}-7{\times}10^{-4}$, respectively. The distortions of the source distribution were proportional to the offset angle.

• Ecology and Resilient Infrastructure
• /
• 제8권2호
• /
• pp.88-96
• /
• 2021

표면영상유속계를 이용한 유속 측정 시 하천의 넓은 영역을 경사지게 촬영하기 때문에 필연적으로 영상 왜곡이 발생하게 된다. 이와 같이 경사영상을 정사영상으로 변환하는 방법으로 수표면과 동일한 평면상의 참조점 좌표를 이용하는 2차원 투영 좌표 변환법을 사용할 경우 홍수 시 수위가 변할 경우 대응이 어렵다는 한계가 있다. 이에 본 연구에서는 수위가 변하더라도 참조점을 재설정할 필요가 없는 경사영상 왜곡 보정 방법을 개발하였다. 본 연구에서 개발한 기법은 높은 위치에 설정한 참조점의 좌표와 카메라의 좌표, 그리고 카메라의 수표면 사이의 연직거리 간의 기하학적인 관계를 이용해 수위 변화에도 대응할 수 있는 경사영상 보정 기법이다. 본 연구에서 개발한 영상 왜곡 보정 방법의 검증을 위해 실규모 하천 실험을 수행하였으며, 참조점 변환식에 대한 검증과 표면유속 측정 결과에 대한 검증을 수행하였다. 검증 결과 개발 기술의 경사영상 보정 정확도는 97% 이상을 나타냈고, 유속 검증 결과 개발 기술을 적용하여 산정한 유속을 비교한 결과 약 4% 이내의 차이를 보이는 것으로 나타나 높은 정확도 확보가 가능한 것으로 나타났다. 따라서 개발 기술을 영상 기반의 고정형 자동유량계측 시스템에 적용한다면 수위가 급변하는 홍수 시 유량측정의 정확도를 개선할 수 있을 것으로 기대한다.

• 구강회복응용과학지
• /
• 제29권3호
• /
• pp.249-258
• /
• 2013

이 연구의 목적은 환자의 머리 위치에 따른 파노라마방사선사진의 수평 및 수직 확대율을 비교 평가하는 것이었다. 직경 4 mm인 금속구를 건조 두개골의 하악 전치부와 우측 대구치부의 치조골 상방에 위치시켰다. 수평 및 수직적 위치의 변화를 재현하기 위해 수직, 수평 이동량을 조절할 수 있는 두개골 고정장치를 이용하여, 전방, 후방, 좌측 및 우측으로 이동시킨 후 파노라마방사선사진을 OP-100D를 이용하여 획득하였다. 촬영된 영상은 DICOM 형식으로 저장되었고, INFINITT PACS software를 이용하여 금속구의 폭과 높이의 평균값을 구하였다. 적절한 위치에서 촬영된 파노라마방사선사진에서 금속구의 수평 확대율은 1.224-1.439였고, 수직 확대율은 1.286-1.345였다. 건조 두개골의 위치 변화에 따른 수평 확대율은 0.798-6.297로 통계적으로 유의한 차이를 보인 반면(P<0.05), 수직 확대율은 1.245-1.418 정도로 수평 확대율에 비해 차이를 보이지 않았다.

• 한국의류학회지
• /
• 제40권1호
• /
• pp.97-113
• /
• 2016

This study develops pant patterns using body shape, measurement and shell mesh data to decide optimal women's pants according to styles with excellent size, fit and shape for different individuals and silhouettes. Standard landmarks, lines, triangles and structures were set on a 3D scanned lower body shell to represent women in their twenties and flattened as a 2D pattern. Patterns were created and analyzed according to culotte, formal, slacks and tight type considering crotch shape, location of the crotch point, and adjusting waist darts. Flattened patterns were rotated to compare existing methods. The crease lines were then set through the hip protrusion point and compared. The main factor of the pant pattern were extracted, total rise, crotch depth, crotch width, angle of center line, shape of the center line curve, the thigh width, the amount of waist dart, and crease line position. With going tight style from the culotte, the fits are closer to the figure with minimized thigh circumference, the dart amount decreases, the crotch depth increases, the crotch extensions were shorter, and the angle of the center back increased. The total rise is U shape for culotte and is closer to V shape as the silhouette tightens. T-test of appearance evaluation of the developed pant pattern were conducted after analyzing measurements and shapes of each styles. The results of the developed patterns were superior to existing patterns in accordance to hip line between body and pants as well as appearance evaluation. We found systematic mechanisms among pattern factors that create various pant silhouettes. Evidence on classification of the silhouettes of traditional types of pants were explained objectively through the process of playing out 3D forms.

• 천문학회지
• /
• 제54권2호
• /
• pp.49-60
• /
• 2021

Observations of line of sight (LOS) Doppler velocity and non-thermal line width in the off-limb solar corona are often used for investigating the Alfvén wave signatures in the corona. In this study, we compare LOS Doppler velocities and non-thermal line widths obtained simultaneously from two different instruments, Coronal Multichannel Polarimeter (CoMP) and Hinode/EUV Imaging Spectrometer (EIS), on various off-limb coronal regions: flaring and quiescent active regions, equatorial quiet region, and polar prominence and plume regions observed in 2012-2014. CoMP provides the polarization at the Fe xiii 10747 Å coronal forbidden lines which allows their spectral line intensity, LOS Doppler velocity, and line width to be measured with a low spectral resolution of 1.2 Å in 2-D off limb corona between 1.05 and 1.40 RSun, while Hinode/EIS gives us the EUV spectral information with a high spectral resolution (0.025 Å) in a limited field of view raster scan. In order to compare them, we make pseudo raster scan CoMP maps using information of each EIS scan slit time and position. We compare the CoMP and EIS spectroscopic maps by visual inspection, and examine their pixel to pixel correlations and percentages of pixel numbers satisfying the condition that the differences between CoMP and EIS spectroscopic quantities are within the EIS measurement accuracy: ±3 km s-1 for LOS Doppler velocity and ±9 km s-1 for non-thermal width. The main results are summarized as follows. By comparing CoMP and EIS Doppler velocity distributions, we find that they are consistent with each other overall in the active regions and equatorial quiet region (0.25 ≤ CC ≤ 0.7), while they are partially similar to each other in the overlying loops of prominences and near the bottom of the polar plume (0.02 ≤ CC ≤ 0.18). CoMP Doppler velocities are consistent with the EIS ones within the EIS measurement accuracy in most regions (≥ 87% of pixels) except for the polar region (45% of pixels). We find that CoMP and EIS non-thermal width distributions are similar overall in the active regions (0.06 ≤ CC ≤ 0.61), while they seem to be different in the others (-0.1 ≤ CC ≤ 0.00). CoMP non-thermal widths are similar to EIS ones within the EIS measurement accuracy in a quiescent active region (79% of pixels), while they do not match in the other regions (≤ 61% of pixels); the CoMP observations tend to underestimate the widths by about 20% to 40% compared to the EIS ones. Our results demonstrate that CoMP observations can provide reliable 2-D LOS Doppler velocity distributions on active regions and might provide their non-thermal width distributions.

• 한국의류산업학회지
• /
• 제21권2호
• /
• pp.171-178
• /
• 2019

This study analyzed the pressure, subjective wearing comfort, and design preference of brassiere shoulder straps among women in their 20s and 40s. Experimental clothing was made by different shoulder strap designs on a brassiere. In the four designs (A-D), the front attachment points of the shoulder straps were the same, but the back attachment points were different. Three of them (E, E1, E2) were of a halter neck design, with different front attachment positions. The pressures of A-D were measured at the position passing through the shoulder line (P1), and E-E2 was measured at the back neck (P2) as well as at P1. Subjective wearing comfort and design preference were rated on a 7-point Likert scale. A was determined to exert the highest pressure at the neck side of the design in the pressure measurement analysis of A-E2, whereas E1 exerted the lowest. E was measured to have the highest pressure among the E-E2 designs, whereas E2 had the lowest. Participants preferred A the most and E the least in regards to the subjective wearing comfort of A-E. Thus, participants deem A to be the most comfortable despite the high strap pressure. However, E was the most favored design, despite its poor wearing comfort. Participants' subjective impressions of E-E2 were that E2 was the most uncomfortable, but its design was the most preferred. Consumers' design preferences and subjective impressions of wearing comfort did not match.

• 대한방사선치료학회지
• /
• 제35권
• /
• pp.7-13
• /
• 2023

목 적: 본 연구에서는 자궁경부암이 자궁과 함께 몸 밖으로 돌출되었을 때 맞춤형 Bolus를 사용하는 것이 치료계획에서 선량 전달에 미치는 영향을 평가하고 환자 set-up에서의 재현성을 평가하고자 한다. 대상 및 방법: 치료 계획은 Eclipse Treatment Planning System (Version 15.5.0, Varian, USA)을 사용했으며 치료기는 VitalBeam (Varian Medical Systems, USA)을 사용하였다. 방사선 치료 기법은 3D-CRT로 AP/PA 방향으로 6MV 에너지를 이용하였다. 처방 선량은 1.8 Gy/fx이고 총 선량은 50.4 Gy/28 fx이다. 이온챔버는 Semiflex TM31010 (PTW, Germany)을 사용하였으며, 각 위치 이동 및 종양 중심 선량에 따른 계획선량과 측정된 선량을 비교하여 선량 분포를 분석 및 평가하였다. 첫 번째 측정은 팬텀에 맞춤형 Bolus를 적용하여 중심에서 수행하였으며, 위치 오차를 가정하여 중심에서 X, Y, Z축 방향으로 -2 cm ~ +2 cm 범위에서 이동하면서 측정하였다. 0.5 cm 간격으로 측정하였으며, Y축 방향은 ±3 cm까지 측정하였고 Bolus가 잘못 set-up된 상황도 측정하였다. 측정된 선량은 팬텀의 air cavity 대신 실리콘의 CT Hounsfield Unit (HU) 240으로 보정된 선량을 기준으로 비교하였다. 결 과: 위치 오차는 모든 X, Y, Z축에서 최대 ±2 cm까지 약 -1%이다. Y축의 경우 +3 cm의 차이가 발생했을 때 -9.73%의 오차가 발생하였다. 그리고 Bolus가 피부에 올바르게 부착되지 않았을 때 -2.6%, 완전히 제거되었을 때 3.92%의 오차가 있었다. 결 론: 맞춤형 Bolus를 사용한 경우 치료 선량 분포가 균일했으며, 위치 오차가 발생한 경우에도 처방 선량과 실제 측정값 사이에 큰 차이가 없었다. 기존 시트형 Bolus는 몸 밖으로 튀어나온 불규칙한 모양의 종양을 보완하기는 어렵지만 맞춤형 Bolus는 치료 선량을 균일하게 전달하는데 유용한 것으로 확인된다.

• Tribology and Lubricants
• /
• 제34권2호
• /
• pp.43-48
• /
• 2018

This paper presents the thermohydrodynamic analysis of tilting journal pad bearings supporting a power turbine rotor applied to a 250 kW super-critical $CO_2$ cycle. In the analysis, the generalized Reynolds equation and 3D energy equation are solved to predict oil film temperature and the 3D heat conduction equation is solved for pad temperature. The power turbine rotor is supported by two tilting pad bearings consisting of five pads with an oil supply block between the pads. Copper backing pads with higher thermal conductivity compared to steel backing pads are adopted to improve thermal management. The predicted maximum pad temperature is around $55^{\circ}C$ which is approximately $15^{\circ}C$ higher than oil supply temperature. In addition, the predicted minimum film thickness is 50 mm at a rotating speed of 5,000 rpm. These results indicate that there is no issue in the thermal behavior of the bearing. An operation test is performed with a power turbine module consisting of a power turbine, a reduction gear and a generator. Thermocouples are installed at the 75% position from the leading edge of the pad to monitor pad temperature. The power turbine uses compressed air at a temperature of $250^{\circ}C$ in its operation. The steady state pad temperatures measured in the test show good agreement with the predicted temperatures.

• The International Journal of Costume Culture
• /
• 제13권2호
• /
• pp.118-129
• /
• 2010

Digital technology introduced into the clothing and fashion industry is evolving to digital virtual fashions and consumer-centered mass-customized production systems. Today the application of such 3D virtual try-on systems is being expanded gradually in the clothing industry. This study purposed to make virtual avatars and virtual garments using OptiTex and V-stitcher virtual software and compared the appearance of the virtual garments put on the virtual avatars. For this, we created virtual avatars and virtual garments using body measurements obtained from jive subjects of top jive body shapes, respectively, using $[TC]^2$ body scanner. According to the results of comparing the outcomes of the two different virtual software systems, virtual avatar II of V-Stitcher tended to have a more round and lifted hip and the waist line at a higher position. In addition, the body curves and shapes of a virtual avatar affect the appearance of virtual garments. This study applied the same body measurements to virtual avatars and the same pattern to virtual garments, but when different kinds of virtual software were used, the virtual avatars and virtual garments showed different appearance and fit. This result may mean that when customers buy apparel products using different kinds of virtual try-on systems, their evaluation of appearance can vary depending on the virtual try-on system. Therefore, research needs to be made actively for the development and use of linkage programs that can reflect actual body measurements between virtual software systems and 3D body scanning systems.

• The Journal of Korean Physical Therapy
• /
• 제27권5호
• /
• pp.311-314
• /
• 2015

Purpose: This study attempted to determine intra-rater reliability and inter-rater reliability for measurement of foot form using the FPI-6 (Foot Posture Index) in patients with hemiplegia caused by stroke. Methods: Twenty two stroke patients were recruited into the research and their foot posture was evaluated using the FPI. Two raters assessed 6 items sequentially in accordance with the FPI-6 manual. This procedure involved asking the subject to take several steps in-place, prior to settling into a comfortable stance position with double limb support. Subjects were instructed to stand still with their arms by their sides and look straight ahead. FPI-6 values ranged from -2 to +2 for each of the six criteria and from -12 to +12 for the total score, indicating a position for each foot either along the supinated (negative score) to pronated (more than +6) continuum of foot posture. Results: The results showed that intra-rater reliability and inter-rater reliability for a total FPI-6 score was high: 0.807-0.888. An almost perfect agreement between the two raters was identified in the foot's morphological classification (Somer's D=0.712; p<0.05). Intra-percentage agreement was high (88.6%). Conclusion: The FPI-6 is a quick, simple, and reliable clinical tool with demonstrated good to excellent intra-rater reliability and good inter-rater reliability when used in assessment of the stroke patient's foot.