Browse > Article
http://dx.doi.org/10.9725/kts.2018.34.2.43

Thermal Analysis and Temperature Measurement of Tilting Pad Bearings Supporting a Power Turbine for the Supercritical CO2 Cycle Application  

Lee, Donghyun (Dept. of System Dynamics, Korea Institute of Machinery and Material)
Kim, Byungok (Dept. of System Dynamics, Korea Institute of Machinery and Material)
Lim, Hyungsoo (Dept. of Energy Conversion System, Korea Institute of Machinery and Materials)
Publication Information
Tribology and Lubricants / v.34, no.2, 2018 , pp. 43-48 More about this Journal
Abstract
This paper presents the thermohydrodynamic analysis of tilting journal pad bearings supporting a power turbine rotor applied to a 250 kW super-critical $CO_2$ cycle. In the analysis, the generalized Reynolds equation and 3D energy equation are solved to predict oil film temperature and the 3D heat conduction equation is solved for pad temperature. The power turbine rotor is supported by two tilting pad bearings consisting of five pads with an oil supply block between the pads. Copper backing pads with higher thermal conductivity compared to steel backing pads are adopted to improve thermal management. The predicted maximum pad temperature is around $55^{\circ}C$ which is approximately $15^{\circ}C$ higher than oil supply temperature. In addition, the predicted minimum film thickness is 50 mm at a rotating speed of 5,000 rpm. These results indicate that there is no issue in the thermal behavior of the bearing. An operation test is performed with a power turbine module consisting of a power turbine, a reduction gear and a generator. Thermocouples are installed at the 75% position from the leading edge of the pad to monitor pad temperature. The power turbine uses compressed air at a temperature of $250^{\circ}C$ in its operation. The steady state pad temperatures measured in the test show good agreement with the predicted temperatures.
Keywords
super critical $CO_2$; tilting pad bearing;
Citations & Related Records
Times Cited By KSCI : 3  (Citation Analysis)
연도 인용수 순위
1 Bae, Y., Cho, J., Shin, H., Lee, K., "A supercritical carbon dioxide cycle power cycle tehcnologys", J. of KSME, Vol. 58, pp. 28-32, 2018.
2 Turchi, C., Ma, Z., Wagner, M., "Thermodynamic study of advanced supercritical carbon dioxide power cycles for concentrating solar power systems", J. of Sol. Energy Eng., Vol. 135, pp. 041007, 2013.   DOI
3 S. Cho, M. Kim, S. Baik, Y. Ahn, J. Lee, "Investigation of the bottoming cycle for high efficiency combined cycle gas turbine system with supercritical carbon dioxide power cycle", Turbo Expo, Montreal, Canada, June, 2015.
4 Huck, P., Freund S., Lehar, M., Peter, M., "Performance comparison of supercritical $CO_2$ versus steam bottoming cycles for gas turbine combined cycle applications", The 5th International Symposium - Supercritical $CO_2$ Power Cycles, San Antonio, Texas., U.S.A., March, 2016.
5 Kus, B., Neks, P., "Development of one-dimensional model for initial design and evaluation of oil-free CO2 turbo-compressor", Int. J. of Refrig., Vol. 134, pp. 2079-2090, 2013.
6 Pecnik, R., Rinaldi, E., and Colonna, P., "Computational fluid dynamics of radial compressor operating with supercritical $CO_2$", J. of Eng. Gas Turbines and Power, Vol. 134, pp. 122301, 2013.
7 D. Lee, B. Kim, H. Lim, M. Park, D. Kang, B. Choi, "Rotordynamic characteristic analysis for axial turbine for the 10 mw super-critical $CO_2$ cycle application", The KSFM J. of Fluid Machinery, Vol. 21, pp. 13-18, 2018.   DOI
8 H. Lim, J. Park, E. Yoon, "Introduction to the core fluid machinery for a supercritical carbon dioxide cycle power cycle application", J. of KSME, Vol. 58, pp. 33-37, 2018.
9 D. Lee, B. Kim, "Bearing and rotordynamic performance analysis of a 250 kW reduction gear system", J. Korean Soc. Tribol. Lubr. Eng., Vol. 32, No. 4, pp. 107-112, August, DOI: 10.9725/kstle-2016.32.4.107, 2016.   DOI
10 D. Lee, K. Sun, "Thermohydrodynamic analysis and pad temperature measurement of a tilting pad journal bearing for a turbine simulator", J. Korean Soc. Tribol. Lubr. Eng., Vol. 33, No. 3, pp. 112-118, June, DOI: 10.9725/kstle-2017.33.3.112, 2016.   DOI