• 한국농공학회논문집
• /
• 제60권5호
• /
• pp.135-147
• /
• 2018

The objective of this study was to analyze the characteristics of combined 1D/2D inundation simulation of riverside farmland using the Hydrologic Engineering Center - River Analysis System (HEC-RAS). We compared and analyzed inundation simulation results between 1D and combined 1D/2D hydraulic simulation using HEC-RAS. Calibration and validation of stream stage were performed using three rainfall events. The coefficient of determination ($R^2$) and root mean square error (RMSE) between simulated and observed stream stage were 0.935 - 0.957 and 0.250 m - 0.283 m in calibration and validation, respectively. The inundation area showed no significant difference in 1D and combined 1D/2D simulation ($8.48km^2$ in 1D simulation, $8.75km^2$ in combined 1D/2D simulation). The average inundation depth by 1D simulation was 1.4 m deeper than combined 1D/2D simulation. In the lower inundation depth, the inundation area by combined 1D/2D simulation was larger than inundation area by 1D simulation. As the inundation depth increased, the inundation area by 1D simulation became wider. In the case of the 1D/2D combined simulation, low elevation areas along the river bank were inundated widely. Compared to 1D/2D combined simulation, the flood radius in some sections was longer in 1D simulation. In the 1D analysis, because the low altitude riverside farmlands are also assumed to stream, it is calculated that riverside farmlands have the same stage as the mainstream when the stream is overflowed. Therefore, the inundation area seems to be overestimated in those sections. In other regions, the inundation areas tend to be broken depending on overflow by each stream cross-section. In the case of river flooding, the overflow is expected to flow to the lower area depending on the terrain, such as the results of the combined 1D/2D simulation. It is concluded that the results of combined 1D/2D inundation simulation reflected the topographical characteristics of low-lying farmland.

• Journal of International Society for Simulation Surgery
• /
• 제2권2호
• /
• pp.71-75
• /
• 2015

To overcome limitations of conventional diagnosis and planning for orthognathic surgery, surgeons have begun to use 3-dimensional (3D) virtual simulation to plan complex orthognathic surgery. In many literatures, it has shown that better surgical outcome achieved with 3D virtual simulation than that with conventional methods. But, there is still lack of data about accuracy of maxillary segmental surgery with 3D virtual simulation. The purpose of this paper was to report the case of maxillary segmental orthognathic surgery with 3D virtual simulation and to assess the actual surgical outcome. Though the result was clinically acceptable, discrepancy between 3D simulation and actual surgery was not superior compared with conventional method. The accuracy of 3D simulation surgery and intermediate wafer fabrication for maxillary segmental surgery needs to be improved. Advancement in 3D software program and careful surgical technique will make it more precise and reliable method.

• 한국멀티미디어학회논문지
• /
• 제19권2호
• /
• pp.504-511
• /
• 2016

3D simulation programs or games on a smart phone and a personal computer have often employed 3D graphic processing techniques and 3D graphical views. However, the user interfaces in those 3D programs have sticked to take a typical 2D style user interface and thus the combination of a 2D user interface view and a 3D simulation view give us a mismatched sense. Since a 2D user interface has been based on the windows controls, it causes sometime DC conflicts between a simulation view and an interface view. Therefore, we will implement the UI developing tool which can be inserted into the pipeline structure for the development of a 3D simulation software and also follows the view-handler design pattern in Microsoft windows system. It will provide various graphical effects such as the deformation of UI depending on the view direction of simulation view and the sitting pose of user. This developing tool gives the natural user interface which heightens the sense of unity with a given 3D simulation view.

• 산업공학
• /
• 제25권2호
• /
• pp.216-228
• /
• 2012

BIM-based 4D simulation makes people easily understand complex construction process using 3D graphics model and helps them review and identify the construction schedule in each phase of the construction process. Moreover, 4D simulation can be used as reference data to determine the validity of the process in the design phase and will be utilized as a measure for checking the construction process. Therefore 4D simulation of construction improves efficiency of project management. However, current commercial applications available for 4D simulation do not provide sufficient functions for connection of 3D models and process information. In this paper, we propose an automated generation method through the definition of the process based on a work method template and developed the template based schedule generation system (TSGS).

• 상하수도학회지
• /
• 제26권1호
• /
• pp.87-95
• /
• 2012

In this study, the following conclusions were obtained from an investigation of the effect of the simulation time step on the simulation results of the two-dimensional, vertically averaged sediment transport model SED2D and an analysis of the deposited sediment distribution in suspended sediments of reservoirs according to grain size. The simulation time step has a significant effect on the deposited sediment distribution in a reservoir. In particular, if the simulation time step is set to be excessively large, physically invalid results are obtained. Additionally, in order to determine an appropriate simulation time step for SED2D, the selection of a simulation time step that will allow the analysis of the suspended sediment concentration profile at the main points of the simulation domain is necessary. The deposited sediment distribution in a reservoir according to grain size, including suspended sediments of clay, silt, and sand, was successfully simulated. Such information will prove valuable in application to the establishment of efficient management and reduction measures of reservoir sediment deposits.

• 한국컴퓨터정보학회논문지
• /
• 제13권7호
• /
• pp.221-229
• /
• 2008

컴퓨터와 더불어 멀티미디어의 발전은 가상현실이라는 신기술을 만들어 내게 하였고 가상현실 분야 중 컴퓨터 시뮬레이션 기술은 항공, 자동차, 의학, 스포츠, 교육, 패션 분야에 이르기까지 그 적용이 확대되고 있다 본 연구는 헤어스타일링 분야에서 기존의 2차원 헤어시뮬레이션의 개발 및 상용 현황과, 연구 단계에 있는 3차원 헤어스타일 시뮬레이션의 개발 현황을 살펴본다. 아울러 현재 개발된 3차원 헤어스타일 시뮬레이션이 상용화하기 위해서는 3D 시스템 부스의 조정, 저가 저화질의 카메라 개선 등의 문제점이 있음을 제시하였다. 이를 개선하기 위해서 object photography 방식에서 panoramic photography 방식의 전환, 중 고가의 고화질 카메라로의 대체들을 제안한다.

• 대한교통학회:학술대회논문집
• /
• 대한교통학회 1999년도 제36회 학술발표회논문집
• /
• pp.477-482
• /
• 1999

• Journal of International Society for Simulation Surgery
• /
• 제3권2호
• /
• pp.69-73
• /
• 2016

Traditionally 2D cephalometric analysis has been used for diagnosis and treatment of maxillofacial deformities. However, 2D has some limitations in diagnosis and treatment planning especially facial asymmetry cases. The most weakness of 2D is overlapping and unpredictability. Today 3D treatment tools are used by many maxillofacial surgeons. 3D treatment tools can show ungarbled facial anatomy and do virtual surgery. The aim of this report is to present usefulness of using 3D analysis and virtual orthognathic surgery for severe facial asymmetry patients.

• 한국CDE학회논문집
• /
• 제9권2호
• /
• pp.133-142
• /
• 2004

CAMPfonn2D is a Finite Element Method (FEM) based process simulation system designed to analyze two dimensional (2D) flow of various metal forming processes. It enables designers to analyze metal forming processes on the computer rather than the shop floor using trial and error and provides vital information about material and thermal flow during the forming process to facilitate the design of products. CAMPfonn2D can be used by companies, research institutes and industrial applications to analyze forging, extrusion, drawing, heading, upsetting and many other metal forming processes. Also, process simulation using CAMPfonn2D can be instrumental in cost, quality and delivery improvements at leading companies. Today's competitive pressures require companies to take advantage of every tool for rapid manufacturing of well-designed product. So, the preprocessor of simulation program must be easy to use to speed-up design. In this paper, we introduce new version of Preprocessor and show how easy to use it. And, Preprocessor will prove itself to be easy and extremely effective.

• 산업공학
• /
• 제16권2호
• /
• pp.258-267
• /
• 2003

Recently, virtual reality technologies have been rapidly developed and realtime virtual simulation methods have been extensively employed for several application areas such as game, sports, manufacturing, military, and so on. A 3D database in realtime virtual simulation plays a key role because it makes users feel reality in virtual space. In a application view of 3D database, a systematic construction approach is required to reduce its construction time and increase its quality. However, many researches have been mostly focused on realtime graphic issues and its key technologies. In virtual simulation of transportation equipments, this paper proposes a systematic construction process of 3D database consisting of four stages as follows: 1) determine the activity space of a equipment, 2) collect data related to 3D database construction, 3) make a 3-dimensional modeling strategy, and 4) generate and evaluate a 3D model. This paper also introduces a new procedure of 3D environment modeling, which summarizes and expands our modeling experiences, to be used as a modeling guide.