• Journal of electromagnetic engineering and science
• /
• 제9권3호
• /
• pp.146-151
• /
• 2009

This paper presents a low-loss broadband balun that uses a coplanar waveguide-to-slotline field transformation. It operates over a very wide frequency range and is of compact size since it does not depend on a resonant structure. To analyse imbalance, the coplanar wavelength(CPW) input ground is connected to the CPW output ground through various capacitors to introduce common-mode impedances. As the common-mode impedance increased the imbalance became significantly higher at the higher-frequency band compared with the lower-frequency band. The bias-circuit approach is used to improve the operation bandwidth of the lower-frequency band. The measured results show a passband of 200 MHz to 2 GHz, an insertion loss of less than 0.75 dB, and a size of $20{\times}14\;mm$. The amplitude imbalance is approximately 0.3 dB and the phase imbalance is less than $6^{\circ}$ over the entire operational range.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1993년도 추계학술대회 논문집
• /
• pp.71-74
• /
• 1993

In this paper, the permeability(${\mu}$$\sub$r′/, ${\mu}$$\sub$r"/), permittivity($\varepsilon$$\sub$r′/, $\varepsilon$$\sub$r"/) and absorption properties of Ferroxplana/Rubber composites were investigated. The composite specimens were prepared by molding and curing the mixtures of matrix rubber and Ni$_2$Y ferroxplana powders which were synthesized by coprecipitated method. The permeability(${\mu}$$\sub$r′/) of specimen was decreased in the range of 8∼12.5(GHz) and the permeability(${\mu}$$\sub$r"/) and Permittivity($\varepsilon$$\sub$r′/, $\varepsilon$$\sub$r"/) were increased. The optimum thickness of electromagnetic wave absorber (F/R=4, 1,200($^{\circ}C$) ), utilizing the Smith chart, was about 3.0(mm). The Figure of Merit was 93(%).

• 전자공학회논문지A
• /
• 제31A권1호
• /
• pp.65-70
• /
• 1994

GaAs power MESFETs with 0.8$\mu$m gate lengths are fabricated using image reversal (IR) methods on the wafer with an undoped surface layer grown by MOCVD. The fabricated GaAs power MESFETs with an undoped surface layer show that an ideality factor 1.17, a built-in potential 0.83 V, a pinch-off voltage -2.7 V, a specfic contact resistance 1.21$\times$10$^{5}$ ~3.42$\times$10$^{2}$$\Omega$-cm$^{2}$ and an extrinsic g$_{m}$ = 103.5 mS/mm. The maximum RF output power densities of the 0.8$\mu$m devices are 360 mW/mm and 499 mW/mm, and power added efficiencies 29.67% and 29.05%, for the unit gate width 150$\mu$m and 200$\mu$m at 12 GHz.

• 천문학회보
• /
• 제39권2호
• /
• pp.73.2-73.2
• /
• 2014

We investigate the rotation measure (RM) of the nearby low luminosity AGN M87 by using archival polarimetric VLA data at 8, 15, 22 and 43 GHz. For the first time, the RM properties of its jet are resolved at at arc-second scales. The distribution of the RM appears to be a gaussian with a mean value of ~200rad/m2 and the power spectrum follows a power law with index -2.5. A simple Kolmogorov model assuming a random turbulent magnetic fields extrinsic to the jet appears not to be adequate to explain the observed RM power spectra. On the other hand, underlying RM gradients possibly connected with the jet could be a possible interpretation.

• 전자공학회논문지D
• /
• 제34D권11호
• /
• pp.83-89
• /
• 1997

An optimize delectroabsorption modulator structure is designed for high speed optical communication systems considering the extinction efficiency, operating bandwidth, polarization loss, and wavelength chirping. the operating wavelength region is $1.55\mu\textrm{m}$ and the deep ridge structure is adapted for th eminimum polarization loss. Simulations show that the absorption layer thickness larger than $0.25\mu\textrm{m}$, and the modulator length shorter than $200\mu\textrm{m}$ are required for the bandwidth over 10GHz. To obtain the modulatiron efficiency over 10dB/V, a wavelength detuning needs to be determined less than 40meV.

• ETRI Journal
• /
• 제29권4호
• /
• pp.452-456
• /
• 2007

Very compact 4-channel 200-GHz-spacing external cavity lasers (ECLs) were fabricated by hybrid integration of reflection gratings and superluminescent laser diodes on a planar lightwave circuit chip. The fifth-order gratings as reflection gratings were formed using a conventional contact-mask photo-lithography process to achieve low-cost fabrication. The lasing wavelength of the fabricated ECLs matched the ITU grid with an accuracy of ${\pm}0.1$ nm, and optical powers were more than 0.4 mW at the injection current of 80 mA for all channels. The ECLs showed single mode operations with more than 30 dB side lobe suppression.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.802-805
• /
• 2003

Structural surface becomes an antenna. The integration of antennas into structural body panels is a new high payoff technology. It emerged from the need to improve structural efficiency and antenna performance. In this paper, we developed new design concept for the structural surface which transmits and receives the electromagnetic signals, and it is termed Surface-Antenna-Structure (SAS). Design procedure was presented including structure design. material selection and design of antenna elements, which was processed according to the communication with KORSAT satellite at Ku-Band (12.25-12.75 GHz). The final demonstration article was 350$\times$200$\times$7.5mm flat antenna panel. Experimental results for antenna performances were in good agreements with design requirements. Also structural analysis was performed with SAS. estimating stress distributions under simply supported condition with Laminated Plate Theories and Wavier Solutions. The SAS concept can be extended to give a useful guide to manufacturers of structural body panels as well as antenna designers. promising innovative future communication technology.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2009년도 춘계학술대회 논문집
• /
• pp.202-206
• /
• 2009

본 논문에서는 X-band GB-SAR 시스템을 이용하여 지상을 모니터링 하였으며, 대기 중의 습도와 거리의 영향을 받는 대기보정 상수를 산출하였다. 시스템에서 X-band 안테나는 중심주파수 9.65 GHz, 밴드 폭 600 MHz이며, 신호의 증폭과 다편파 측정 및 분석을 위해 각각 마이크로파 앰프와 마이크로파 스위치를 이용하였다. Azimuth step과 length는 5 cm와 5 m로 최대 관측 거리는 약 200 m 이다. phase 분석에 쓰인 산란체는 총 5개의 trihedral corner reflector로서, 시스템으로부터의 거리를 각각 다르게 설정하였다. 실험은 3일간 연속적으로 수행되었으며, 실험간 상대습도는 최소 50 %에서 최대 90 %까지로 약 40 %의 변화를 보였다. 고정된 상태의 reflector는 마치 이동한 것과 같은 현상을 보였는데 이는 마이크로화의 전파과정에서 발생하는 거리와 습도에 따른 지연효과라고 판단하였으며, 이를 배제하기 위하여 대기보정식을 산출하였다. 산출과정에서 temporal coherence가 0.98 이하인 reflector의 신호는 제외하였는데 이 경우 시스템 및 reflector의 안정성에 문제가 있다고 판단하였기 때문이다. 산출된 대기보정식은 C-band 안테나를 사용한 실험과 비교하여 보았다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 봄 학술발표회 논문집
• /
• pp.817-820
• /
• 2000

Existence of void or delamination inside building foundation or tunneling lining can cause serious problems in structural safety. Therefore, 0probing of such voids in architectural and civil structures is an important process in evaluating the overall integrity of the structures. In this study, the radar method has been examined in its use in detecting voids inside concrete specimens. The dimensions of the specimens are 1,000 mm(width) $\times$ 600 mm (height) $\times$ 140 mm (thickness). A void is embedded inside concrete specimens with the dimensions of 200 mm(width) $\times$ 600 mm (height) $\times$ 50 mm (thickness). Concrete cover depth of 30 mm, 60 mm is studied for comparison. In both cases, the voids is located with 1 GHz antenna.

• 전자공학회논문지A
• /
• 제31A권9호
• /
• pp.114-120
• /
• 1994

We have been successfully fabricated the low nois HEMT device with AlGaAs and GaAs structure. The epitazial layer with n-type AlgaAs and undoped GaAs was grown by molecular beam epitaxy(MBE) system. Ohmic resistivity of the ource and drain contact is below 5${\times}10^{6}{\Omega}{\cdot}cm^{2}$ by the rapid thermal annealing (RTA) process. The ideality factor of the Schottky gate is below 1.6 and the gate material was Ti/Pt/Au. The HEMTs with 0.25$\mu$m-long and 200$\mu$m-wide gates have exhibited a noise figure of 0.65dB with associated gain of 9dB at 12GHz, and a transconductance of 208mS/mm.