• Korean Journal of Materials Research
• /
• v.9 no.9
• /
• pp.919-925
• /
• 1999

Grain boundary characteristics and corrosion behavior of Alloy 600 material were investigated using the concept of grain boundary control by thermomechanical treatment(TMT). The grain boundary character distribution (GBCD) was analyzed by electron backscattered diffraction pattern. The effects of GBeD variation on intergranular at tack(JGA) and primary water stress corrosion cracking(PWSeC) were also evaluated. Changes in the fraction of coinci dence site lattice(CSL) boundaries in each cycle of TMT process were not distinguishable, but the total eSL boundary frequencies for TMT specimens increased about 10% compared with those of the commercial Alloy 600 material. It was found from IGA tests that the resistance to IGA was improved by TMT process. However, it was found from PWSCC test that repeating of TMT cycles resulted in the gradual decrease of the time to failure and the maximum load due to change in grain boundary characteristics, while the average crack propagation rate of primary crack increased mainly due to suppression of secondary crack propagation. It is considered that these corrosion characteristics in TMT specimens is attributed to 'fine tuning of grain boundary' mechanism.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2005.10a
• /
• pp.173-177
• /
• 2005

리튬이온 2차전지(Lithium ion battery, LIB)는 기존에 사용되던 전지에 비해 에너지 밀도가 높고 충방전 사이클이 우수하다. 이 때문에 휴대전화와 노트북 등에 수요가 급속하게 증가하고 있으며 1995년 LIB의 생산량은 4천만 개에서 2004년에는 약 8억 개로 20배 이상 증가하였다. 이에 따라 폐LIB도 급속하게 증가하게 되어 전국적인 재활용 시스템의 확보가 필요한 실정이다. 본 연구에서는 폐LIB에 함유되어 있는 유가금속 중에서 리튬코발트옥사이드(이하 $LiCoO_2$)를 회수하기 위하여 분쇄기(orient vertical cutting mill)와 진동 Screen을 사용하여 유기분리막, 금속류(Aluminium foil, Copper foil, case 등) 그리고 전극물질(lithium cobalt oxide와 graphite 등의 혼합 분말)로 분리하였다. 전극물질에서 $LiCoO_2$와 graphite 분리를 위한 전처리 단계로서 $500^{\circ}C$ 정도의 열처리를 하여 $LiCoO_2$의 표면 성질을 변화시켜 부유선별에 의해 $LiCoO_2$와 graphite의 분리가 가능하도록 하였다. 부유선별 실험 결과 93% 이상의 순도를 가지는 $LiCoO_2$를 92% 이상 회수할 수 있었다.

• Electrical & Electronic Materials
• /
• v.8 no.6
• /
• pp.737-743
• /
• 1995

Two step RTD(Rapid Thermal Diffussion) of P into silicon wafer using tungsten halogen lamp was used to fabricated very shallow n$^{+}$p junction. 1st RTD was performed in the temperature range of 800.deg. C for 60 see and the heating rate was in the 50.deg. C/sec. Phosphrous solid source was transfered on the silicon surface. 2nd RTD process was performed in the temperature range 1050.deg. C, 10sec. Using 2 step RTD we can obtain a shallow junction 0.13.mu.m in depth. After RTD, the Ti-silicide process was performed by the two step RTA(Rapid Thermal Annealing) to reduced the electric resistance and to improve the n$^{+}$p junction diode. The titanium thickness was 300.angs.. The condition of lst RTA process was 600.deg. C of 30sec and that of 2nd RTA process was varied in the range 700.deg. C, 750.deg. C, 800.deg. C for 10sec-60sec. After 2 step RTA, sheet resistance was 46.ohm../[]. Ti-silicide n+p junction diode was fabricated and I-V characteristics were measured.red.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.61-61
• /
• 1999

저항이 5$\Omega$-cm인 n-type Si(100) 웨이퍼를 실리콘 식각시 마스크로 사용하기 위하여 습식 열산화법을 이용하여 100$0^{\circ}C$에서 SiO2을 2400$\AA$ 성장시킨 후, OPCVD 공정을 통해 785$^{\circ}C$서 SiH2Cl2 가스 30sccm과 NH3가스 100sccm을 이용하여 Si3N4를 3000$\AA$ 증착시켰다. 이 웨이퍼를 포토-리쏘그라피 공정을 거쳐 지름 2$\mu\textrm{m}$의 포토레지스트 패턴을 제작한 후 600W의 RF power하에서 CF4 가스 10sccm, CHF3 가스 15sccm, O2가스 8sccm 및 Ar가스 10sccm을 이용하여 MERIE 방법으로 Si3N4를 식각한 다음, 7:1 BHF 용액내에서 30초간의 습식식각을 통해 40wt.%의 KOH 용액내에 8$0^{\circ}C$에서 30초간의 이방성 식각을 통해 피라미드 모양의 Si FEA(field emitter array)를 제작하였다. 본 실험은 다음과 같이 완성된 Si FEA를 샤프닝 산화 후 산화막 식각을 통해 마스크를 제거한 다음, tip의 열화학적 내구성을 증가시키고 장시간 구동시 안정성과 전계방출 전류밀도를 높이기 위해 tip의 표면에 Ti를 sputter 방법으로 약 300$\AA$ 증착시킨 후, RTA 장비를 이용하여 2단계 열처리 (first annealing:$600^{\circ}C$/30sec, second annealing : 85$0^{\circ}C$/15sec)를 통해 Si FEA의 경우보다 낮은 turn-on 전압과 높은 전계방출 특성을 나타낼 것으로 기대된다.

• Korean Journal of Food Science and Technology
• /
• v.50 no.3
• /
• pp.292-296
• /
• 2018

Softening effects of enzyme following pre-treatments were examined. Four pre-treatments: raw (R), heat (H), heat and freeze-thawing (HFT), heat and freeze-drying (HFD) were applied to carrot. Subsequently, each treated sample was immersed in 10% celluclast enzyme solution for up to 6 h and then their properties were compared. The minimum and the maximum color change was observed in HFD and H, respectively. R showed no change in hardness after 6 h immersion, indicating that the enzyme did not penetrate the carrot. The number and size of pores were greater in samples undergone HFT or HFD as observed by microstructure analysis using SEM, and HFD caused 99.5% reduction in hardness after 6 h immersion. After 6 h immersion post-HFT or 3 h immersion post-HFD, the hardness was less than $20,000N/m^2$, indicating tongue ingestion was possible, and the samples retained their original shape and easily collapsed by spoon pressing.

• Progress in Superconductivity
• /
• v.4 no.1
• /
• pp.90-93
• /
• 2002

The sintering process of BSCCO 2223 tapes is a complex process that is very sensitive to parameters, such as temperature, oxygen partial pressure, heating and cooling rate and holding time. During the first heat treatment, 2212 phase of precursor powder is partially transformed into 2223 phase and some residual secondary phases, such as $(Bi,Pb)_2$$Sr_2$CuO／sub y／(2201), $(Ca,Sr)_2$CuO／sub y／(2/1AEC), (Ca,Sr)／sub 14／Cu／sub 24／O／sub 41／(14／24 AEC) etc. The secondary phases are difficult to be removed from the BSCCO 2223 matrix on the heat treatment. These secondary phases degrade the critical current density. In order to minimize the amount and size of alkaline earth cuprate(AEC) particles step heat treatment is applied during the first heat treatment under the varying atmosphere. Experimental results showed that by adapting the step heat treatment process, the amount and particle size of the secondary phases in the final tapes are decreased. Consequently, the BSCCO 2223grain texture and Jc properties are improved.

• Composites Research
• /
• v.26 no.2
• /
• pp.123-128
• /
• 2013

The PVDF (polyvinylidene fluoride) fibers were prepared using the wet spinning processing. To improve ${\beta}$-phase crystalline which closely related piezoelectric property PVDF wet spun fibers conducted post treatment. Post treatment is consisted of heat stretching and annealing process. The heat stretching and annealing conditions were controlled by changing temperature between glass transition temperature and melting temperature. From these experimental data, the resulting crystal structure of the ${\beta}$-phase crystalline was confirmed by FT-IR and XRD experiments. From these analysis results, optimum stretching and annealing conditions of the wet spun PVDF fibers were founded to increase high ${\beta}$-phase crystalline. Furthermore results showed that thermal processing had a direct effect on modifying the crystalline microstructure and also confirmed that heat stretching and annealing could increase the degree of crystallinity and ${\beta}$-phase crystalline. Finally, piezoelectric constant ($d_{11}$) of the post heat treated PVDF fibers reinforced composite were measured to investigate the feasibility for the sensing materials.

• Polymer(Korea)
• /
• v.32 no.1
• /
• pp.56-62
• /
• 2008

Three types of network polyesters have been newly synthesized by a two-step condensation reaction by the various combination of several diols and diacids. When these polymer films were thermally treated at $240^{\circ}C$, they exhibited absorptions in a visible range despite the forbidden transition of carbonyl group. When excited at wavelengths above 330 nm, the polymers showed fluorescences in a wide visible range from blue to near yellow. These fluorescence phenomena are due to the formation of certain conjugated structures by the Knoevenagel type self-condensation under the high-temperature thermal treatment. These polymers showed significant difference in the thermal properties as a function of the degrees of chemical crosslinking. They also underwent photodegradation. Highly resolved, fluorescent image patterns were successfully obtained by the photodegradation of malonate group under a strong UV-light irradiation.

• Journal of the Korean Ceramic Society
• /
• v.36 no.3
• /
• pp.307-318
• /
• 1999

동결건조법에 의한 저유전성 실리카 박막의 제조공정 개발 및 층간 절연물질로의 응용성이 연구되었다. 코팅용 폴리머 실리카 졸은 TEOS와 이소프로판올(iso-propanol:IPA)또는 터트부탄올(tert-butanol:TBA)을 용매로한 2단계 공정에 의하여 제조되었으며, 이들 졸을 p-Si(111)웨이퍼 상에 스핀코팅한 습윤겔 박막을 동결건조 하여 다공성 실리카 박막을 제조하였다. 균일한 박막 코팅층을 얻을 수 있는 실리카 졸의 최적 점도범위는 IPA와 TBA를 용매로 한 실리카 졸의 경우 각각 10~14 cP와 20~30cP 정도였으며 스핀속도는 2000 rpm 이상이었다. 결함이 없는 다공성 실리카 박막은 TBA(빙점 $25^{\circ}C$)를 동결용매로 하여-196$^{\circ}C$까지 급랭시킨 후 $0^{\circ}C$와 0.1 torr 까지 가열 감압한 상태에서 고상의 TBAFMF 모두 제거한 다음 20$0^{\circ}C$까지 열처리하여 제조되었다. 다공성 실리카 박막의 두께는 졸의 타입과 스핀코팅 속도에 의해 2500~15000$\AA$범위 내에서 제어가 가능하였으며 이들 막의 밀도와 유전상 수 값은 각각 0.9$\pm$0.3g/㎤(기공율 60$\pm$10%)과 2.4 정도였다.

• Food Science of Animal Resources
• /
• v.22 no.2
• /
• pp.179-182
• /
• 2002

Using differential scanning calorimetry (DSC), changes underwent by a mixture of $\alpha$-lactalbumin ($\alpha$-La) and $\beta$-lactoglobulin ($\beta$-Lg) during heat treatment were studied, yielding useful information for the dairy industry. Results of the DSC showed that the heat denaturation temperature of the hobo-$\alpha$-La was higher than that of apo-$\alpha$-La, suggesting hole-$\alpha$-La‘s greater stability. The denaturation temperature of a mixture of holo-$\alpha$-La and $\beta$-Lg was also slightly lower than that of holo-$\alpha$-La alone. The denaturation temperature of an apo-$\alpha$-La and $\beta$-Lg mixture was higher than that of holo-$\alpha$-La and $\beta$-Lg, suggesting that the heat stability of apo-$\alpha$-La was increased by $\beta$-Lg. Based on these results, it is possible to conclude that a mixture of holo-$\alpha$-La and $\beta$-Lg is more intensively affected by an increase in temperature than other samples, and that free sulphydryl groups seem to take part in this heat-induced denaturation.