• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.155-160
• /
• 2004

This paper presents a study on the permittivities of the carbon black/epoxy composite at microwave frequency. The measurements were performed at the frequency band of $1 GHz\~18GHz$. The results show that the complex permittivities of composites depend strongly on the natures and concentrations of the carbon black dispersion. The frequency spectrums of dielectric constants and ac conductivities of composites show the good conformities with descriptions of the percolation theory. The carbon black concentration dependencies do not have conformities with the descriptions of percolation theory and there is no peculiar concentration like percolation threshold, on that concentration, the conductivity of composite jumps up. A new scheme, that is a branch of Lichtenecker-Rother formula, is proposed to obtain a mixing law to describe the complex permittivities of the composites as function frequency and concentration of carbon black.

• Polymer(Korea)
• /
• v.33 no.5
• /
• pp.420-428
• /
• 2009

In this study, the composites containing carbon black (CB) or carbon fibers were prepared, and the microwave absorbing properties and the absorption mechanism of them were investigated and discussed in the frequency range of 2-18 GHz, respectively. The optimum mass fraction of CB has been found as 6%, and the carbon fibers were discovered to absorb radar wave either under parallel or vertical polarization, the suitable gap distance between each bundle of which was 5 mm. According to the results of the single constitute absorber samples, the structured composites with the two kinds of absorbers combination were fabricated and studied at 2-18 GHz. The top layer absorbers affect the absorption performance a lot; the maximum reflection loss of composites with CB as top layer absorbers was -31.8 dB with the frequency range of 2.4 GHz below -10 dB, and the other type with CFs as the top layer absorbers obtained the reflection loss peak value of -31.4 dB with 2 GHz below-10 dB.

• Composites Research
• /
• v.22 no.3
• /
• pp.44-54
• /
• 2009

In this paper, we proposed a numerical model the complex permittivity for the E-glass fabric/epoxy composite laminate containing electrical conductive carbon black. The model is based on the percolation theory and for the composites over than the percolation threshold and in higher frequency band in that the AC conductivity is fully proportional to the frequency. The measurement for the complex permittivity wasperformed at the frequency band of 0.5 GHz $\sim$ 18.0 GHz using a vector network analyzer with a 7 mm coaxial air line. The proposed model is composed of the numerical equations of the scaling law used in percolation theory and constants obtained from experiments to quantify the model itself. The model describes the complex permittivity as the function of frequency and filler concentration. The model was verified by being compared with the measurements.

• Journal of the Korean Ceramic Society
• /
• v.39 no.1
• /
• pp.26-32
• /
• 2002

The effects of $Nd_2O_3$ addition to $Q{\cdot}f_{0}(GHz)$ ceramics with ${\varepsilon}_r$ of 126, $Q{\cdot}f_{0}(GHz)$ of 2240 and of $68\;ppm/^{\circ}C$ on their microwave properties were investigated. For the addition of 5 wt% $Nd_2O_3$, the dielectric constant (${\varepsilon}_r$) showed maximum value of 131, then decreased with the further addition of $Nd_2O_3$. $Q{\cdot}f_{0}(GHz)$ value was still increased to 3533 with 9 wt% $Nd_2O_3$ addition, it is influenced by densification of grain boundary. With more addition of $Nd_2O_3$ up to 18 wt%, the abnormal grain growth have influence on the decreasing of $Q{\cdot}f_{0}(GHz)$ value. But with the further addition of $Nd_2O_3$ over 25 wt%, the $Q{\cdot}f_{0}(GHz)$ value was again increased by the effect of the second phase ($Nd_2Ti_2O_7$) forming. The temperature coefficient of resonant frequency (${\tau}_f$) was decreased from $+\;68\;ppm/^{\circ}C$ with the addition of $Nd_2O_3$, reached $0\;ppm/^{\circ}C$ at 12 wt% addition, and became negative with the further addition of $Nd_2O_3$. The optimum microwave dielectric properties were obtained for $0.3CaTiO_3-0.7(Li_{1/2}Nd_{1/2})TiO_3$ with 9 wt% $Nd_2O_3$ sintered at $1425^{\circ}C$ for 3 hrs. The dielectric constant (${\varepsilon}_r$), the $Q{\cdot}f_{0}(GHz)$ value, and the temperature coefficient of resonant frequency (${\tau}_f$) were 108, 3533, and $+\;6\;ppm/^{\circ}C$, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.8
• /
• pp.1102-1107
• /
• 1993

Microwave dielectric properties of CaTiO3 and CaTiO3-TiO2 ceramics for the composition range between 40 and 50 mol% CaO in CaO-TiO2 binary system were investigated. CaTiO3 ceramics with50 mol% CaO showed the dielectric constant (e,) of 178, the temperature coefficient of resonant frequency(c,) of+1000 ppm/'c and the qualify factor Q of 2760 (f0=2.7 GHz ). Dielectric constant and temperature coefficient of resonant frequency of ceramics with dual phases of CaTiO3 and TiO2 decreased gradually from those of CaTiO3 as the CaO content decreased. Q value and density were found to have minimum at the composition of 47 mol% CaO. The degradation of Q value and density in dual phase ceramics seems to be caused by the large pores at grain boundaries and/or within grains remained after rapid growth of CaTiO3 grains as TiO2 Phase decreased.

• Journal of Broadcast Engineering
• /
• v.3 no.1
• /
• pp.93-99
• /
• 1998

본 논문에서는 Ka-밴드 위성통신 송신주파수대역(30.085∼30.885 GHz)의 대역통과 필터를 유도성 fin-line 구조를 이용하여 분석, 설계 및 제작하였다. 도파관내의 공진기들이 전계면에 수직한 금속 fin으로 구성된 구조를 해석하는데 가장 적합한 모드정합법을 사용하여 설계하였다. 제작된 필터는 마이크로파대역 뿐만 아니라 밀리미터파대역의 주파수에서도 우수한 필터특성을 갖는다는 특징을 가지고 있으며, 상업용 도파관을 사용하는 대신에 가격이 저렴하고 가공이 용이한 알루미늄을 사용함으로써 대량생산이 가능하다. 또한 도파관내 금속삽입형태에 의한 대역 통과 필터의 구현이 아닌 유한한 두께를 갖는 포토-에칭된 유전체 기판을 삽입함으로써 제작성의 어려움을 해결하였다. 설계, 제작된 필터의 측정결과 통과대역내에서 1.6dBal만의 삽입손실과 18dB이상의 반사손실을 갖는 응답특성을 얻었으며 이론에 의한 계산치와 측정치와의 비교를 통해 본 논문에서 제안된 설계방법의 타당성을 입증하였다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.7
• /
• pp.771-777
• /
• 2008

In this paper, a frequency doubler using modified time-delay technique is proposed. A voltage controlled delay line (VCDL) in the proposed frequency doubler compensates the group delay time mismatching between input and delayed signal. With the group delay time matching and waveform shaping using the adjustable Schmitt triggers, the unwanted fundamental component($f_0$) and the higher order harmonics such as third and fourth are diminished excellently. In result, only the doubled frequency component($2f_0$) appears dominantly at the output port. The frequency doubler is designed at 1.15 GHz of $f_0$ and fabricated with TSMC $0.18\;{\mu}m$ CMOS process. The measured output power at $2f_0$ is 2.67 dBm when the input power is 0 dBm. The obtained suppression ratio of $f_0,\;3f_0$, and $4f_0$ to $2f_0$ are 43.65, 38.65 and 35.59 dB, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.8
• /
• pp.840-845
• /
• 2004

The microstructure and microwave dielectric properties of $(1-x){Mg}_4{Ta}_2{O}_9-xTi{O}_2(x=0\sim0.9)$ ceramics were investigated. The specimens were prepared by the conventional mixed oxide method with sintering temperature of 140$0^{\circ}C$∼150$0^{\circ}C$. To improve the quality factor and the temperature coefficient of resonant frequency,$ Ti{O}_2(\varepsilon\Gamma=100, Q\times f_\Gamma=40,000 GHz,\ta_f= +450 ppm\diagup^{\circ}C $ was added in ${Mg}_4{Ta}_2{O}_9$ceramics. The dielectric and structural properties were investigated. According to the XRD patterns, $(1-x){Mg}_4{Ta}_2{O}_9-xTi{O}_2(x=0\sim0.9)$ ceramics had the ${Mg}_4{Ta}_2{O}_9$ phase(hexagonal) and ${MgTi}_2{O}_5$phase(orthorhombic). The dielectric constant($\varepsilon_r$). quality($Qtimes{f}_r$${\tau}_f$) of the $(1-x){Mg}_4{Ta}_2{O}_9-xTi{O}_2(x=0\sim0.9)$ ceramics were 8.12∼18.59, 18,750∼186,410 GHz and －36.02∼＋3.46 ppm/$^{\circ}C$, respectively.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.11
• /
• pp.50-58
• /
• 2000

A Mach-Zehnder type $Ti:LiNbO_3$ optical modulator with a grooved $SiO_2$ buffer layer, was evaluated in terms of an electrode structure. The finite element method was performed to find out the optinum design parameters of electrodes. characteristic impedance ($Z_o$), MW effective index ($N_{eff}$) and attenuation constant ($a_o$)of fabricated traveling-wave electrodes were measured and compared with those obtained by the simulation expectation. For an optical modulator with 11${\mu}m$thick electrodes and a grooved $SiO_2$ buffer layer, the 3dB bandwidth based on the RF measurement results turned out to be 18GHz.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.6
• /
• pp.532-537
• /
• 2005

In order to develop a tunable resonator which can be easily operated by DC bias and applied for microwave tunable filters and devices using ferroelectric thin or thick films, the non conductor backed-and conductor backed- coplanar stripline resonators have been designed and analyzed. They have been designed to be operated at 25 GHz which involve coplanar stripline input and output ports. The resonators have been simulated and analyzed using Ansoft HFSS. The research has been focused on the Quality factor of the coplanar stripline resonator. The conductor Q, box Q, and radiation Q of the resonators have been analyzed and calculated according to the substrate thickness & conductor width of the resonators. From these parameters, the loss factors of the coplanar stripline resonator have been investigated. The conducting Q of the coplanar stripline resonator has no relation with the thickness of dielectric substrate and increases as the conductor width increases. The box Q has no much relation with the thickness of substrate and the conductor width, which is above 2000. The radiation loss increases as the thickness of substrate and the conductor width increase. To decrease the radiation loss of the coplanar stripline resonator, a conductor backed coplanar stripline resonator has been proposed which has the unloaded Q of 170.