• Transactions of Materials Processing
• /
• v.16 no.1 s.91
• /
• pp.3-8
• /
• 2007

Novel compression molding system for preform has been developed in this study. The preforms for injection blow molding and injection stretch blow molding are being manufactured by injection molding. However it contains gate mark that affects the bottom crack in the PET bottle. The compression molded preform does not contain gate mark, thus the appearance quality of bottle has been increased and the residual stress near gate(bottom of the bottle) has been reduced. The thickness distributions, haze, and transmittance are well accepted for the preform. Also, flow characteristics of the resin between a core and cavity could be analyzed through computer simulation.

• Transactions of Materials Processing
• /
• v.16 no.1 s.91
• /
• pp.61-66
• /
• 2007

Powder injection molding(PIM) is widely used for many parts in the field of automotives, electronics and medical industries, due to the capability of net shaping for complex 3-D geometry. Powder injection mold design for the dental scaler tip, a component of medical appliance, was presented. In comparison with conventional machining process, powder injection molding has many advantages, specially in price and dimensional stability, for molding dental scaler tip which has complex geometry. Both product design and mold design for dental scaler tip were presented. A PIM feedstock was made of stainless series(17-4PH, 316L, 440C) powder and a wax based binder. The 'rapid mold' concept was applied to manufacture the various forms and materials of dental scaler tip including vibration characteristics.

• Journal of mucopolysaccharidosis and rare diseases
• /
• v.1 no.1
• /
• pp.15-18
• /
• 2015

Biopharmaceuticals, with their ability to treat many unmet needs, are seen as promising medications in diabetes mellitus, growth hormone deficiency, chronic renal failure, cancer, and rheumatoid arthritis. However, almost all biopharmaceuticals should be administrated by injection; IV, IM, and SC. In addition, these treatments are long term, and patients should receive frequent injections for many years. Patient compliance is therefore of critical importance to ensure treatment benefits. Therefore, the goal of drug product development should be focused on improving patient compliance by reducing injection-associated pain as well as stable formulation development. This review will suggest the kinds of factors that should be considered to minimize injection pain with regard to formulation, device, and injection procedures focused on SC injections.

• The KSFM Journal of Fluid Machinery
• /
• v.14 no.6
• /
• pp.68-75
• /
• 2011

This study simulated the effect of steam injection on the performance and operation of a gas turbine combined heat and power (CHP) system. A commercial simple cycle gas turbine was analyzed. A full off-design analysis was carried out to investigate the variations in not only engine performance but also the operating characteristics of the compressor caused by steam injection. Variation in engine performance and operation characteristics according to various operation modes were examined. First, the impact of full steam injection was investigated. Then, operations aiming to guarantee a minimum compressor surge margin, such as under-firing and partial steam injection, were investigated. The former and latter were turned out to be relatively superior to each other in terms of power and efficiency, respectively.

• Korean Journal of Animal Reproduction
• /
• v.17 no.1
• /
• pp.21-25
• /
• 1993

We have previously shown that gossypol injection into the stroma of testis was found to effectively inhibit the process of spermatogenesis. In this study, properties and chemistry of blood were investigated weekly in ICR mouse after the injection of gossypol into the testicular stroma(5, 10 or 15mg per kg body weight). There were no significant differences in red blood cell(RBC), hematocrit, white blood cell(WBC), basophils, eosinophils and monocytes during first 4 weeks after injection of gossypol between treatments, but neutrophils increased and lymphocytes decreased, respectively(P<0.05). Total content of protein, albumin and globulin were not different, compared with control. However, the concentration of glucose after injection of gossypol increased significantly(P<0.05). In conculsion, the results of this study indicated that injection of gossypol into stroma of testis might affect both properties and chemistry of blood in mice.

• Transactions of Materials Processing
• /
• v.10 no.5
• /
• pp.402-410
• /
• 2001

The gas-assisted injection molding process is often perceived to be unpredictable, because of the extreme sensitivity of the gas. Since a slight change in design or process parameters can significantly change the resulting gas penetration, few designers and molders have the level of experience with the new gas-assisted injection molding process required for the development of new parts. This paper is concerned with the unified molding for a thick cosmetic chest by using gas-assisted injection molding. CAE analysis was carried out to design the part and the gas channel without inducing sink marks. And based on the part weight measurement, the processing parameters to control gas penetration percentage were chosen through the method of design of experiments. A thick cosmetic chest was successfully produced using the gas assist technology. The sink mark issue associated with the conventional injection molded parts was resolved. Weight savings and cycle-time reduction were also achieved.

• Design & Manufacturing
• /
• v.2 no.4
• /
• pp.5-10
• /
• 2008

Recently, the study for filling imbalance in thermoplastic polymer has gradually been increased. However, it is hard to find the researches for filling imbalance of thermoplastic elastomer(TPE). The experiment of filling imbalance was conducted for the three kinds of thermoplastic vulcanizes(TPVs) and PP polymer in the mold with geometrically balanced runner system(Unary Branch Type Runner System). In this experiment, the effects of the melt temperature, injection pressure and injection speed on the filling imbalance were investigated. There was also the imbalance in TPV injection molding process as well as in conventional injection molding with plastics. The tendency of filling imbalance in TPV injection molding specially decreased by taking place the hesitation of TPV melt.

• Journal of ILASS-Korea
• /
• v.25 no.1
• /
• pp.15-20
• /
• 2020

This study aims to investigate injection rate and microscopic spray characteristics of diesel fuel containing fine air bubble (FBD). fine bubble was generated by cavitation theory using bubble generator. Fuel spray was injected into constant volume chamber and visualized by high speed camera. The injection rate data was acquired with bosch tube method. Injection rate of finebubble diesel was very similar with that of diesel. It showed slightly faster injection start by 5 ㎲ attributed to the low viscosity characteristics. In microscopic spray visualization, fine bubble diesel spray showed unsymmetric spray shape compared with diesel spray. It also showed very vigorous spray atomization performance during initial spray development. Improved atomization was also attributed to the low viscosity and surface tension of finebubble diesel fuel.

• Transactions of Materials Processing
• /
• v.11 no.8
• /
• pp.691-700
• /
• 2002

Injection molded plastic parts have many surface detects: weld line, sink mark, flow mark, gloss, shading, scratching, and so on. Because these surface faults have not been accepted esthetically, plastic parts are Produced through painting or texturing. The purpose of this paper is to develop a paintless molded part of TV Mask Front by flow control method and gas-assisted injection molding. In order to minimize defects from injection molding, this study was carried out using computer aided injection mold filling simulations using MF/FLOW and MF/GAS. Based on these numerical results, we developed FR(Flame Retardant) HIPS and established guidelines of part design, mold design, and Processing conditions. We have achieved of cost sayings, improvement of productivity, and utilization of recycling by eliminating surface defects and painting process.

• Journal of Powder Materials
• /
• v.9 no.4
• /
• pp.245-250
• /
• 2002

In this paper we presented numerical method for the simulation of powder injection molding filling process, which is one of the key processes in powder injection molding. Rheological properties of powder binder mixture such as slip phenomena and yield stress were introduced into the numerical analysis model of powder injection molding filling simulation. Numerical model can be classified into two types. One is 2.5D model which can be introduced to a arbitrary thin geometry and the other is full 3D model which can be applied to a general 3D shape. For 2.5D model we showed the validity of our CAE system with several verification examples. Finally we suggested flow analysis model for 3D powder injection molding filling simulation.