• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.1
• /
• pp.29-35
• /
• 2012

The treatments for spinal canal stenosis are radicular cyst removal, spine fusion, and implantation of an artificial intervertebral disc. Artificial intervertebral discs have been most widely used since the mid-2000s. The study of artificial intervertebral discs has been focused on the analysis of the axial rotation, lateral bending, the degrees of freedom of the disc, and flexion-extension of the vertebral body. The issue of fatigue failure years after the surgery has arisen as a new problem. Hence, study of artificial intervertebral discs must be focused on the fatigue failure properties and increased durability of the sliding core. A finite element model based on an in the artificial intervertebral disc (SB Charit$\acute{e}$ III) was produced, and the influence of the radius of curvature and the change in the coefficient of friction of the sliding core on the von-Mises stress and contact pressure was evaluated. Based on the results, new artificial intervertebral disc models (Models-I, -II, and -III) were proposed, and the fatigue failure behavior of the sliding core after a certain period of time was compared with the results for SB Charit$\acute{e}$ III.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.18 no.1
• /
• pp.87-108
• /
• 1996

This study was intended to perform cephalometric analysis of the facial soft tissue profile after surgical correction of skeletal Class III malocclusion after SSRO in 29 patients (Males 12, females 17). Lateral cephalograms were taken in centric occlusion before and immediate, long term after surgeries. 1. Counter-clockwise rotation of mandible was observed after the surgery, average relapses of mandibular set back were 1.23-1.28mm. The net effects of the mandibular set-back after surgeries were 81.7-82.2%. Because these relapse tendencies may reduce the effects of the surgical outcomes, surgeon must consider these net before the surgical treatment planning. 2. The ratio of horizontal changes of hard tissue to soft tissue at lower lip, mentolabial sulcus, pogonion were 72.7-93.7%, 100.3%, 99.1-102.1% respectively. There were little changes at upper lip position anteroposteriorly. 3. The relationship of upper and lower lips were improved after surgery. Lower lip was posteriorly repostioned and upper lip was flattend and elongated in conjunction with deepening of inferior lobial sulcus. But profile of chin was still prominent after surgery. 4. Hard tissue horizontal changes and tissue vertical changes were significantly correlated with each other and there were reverse correlations with hard tissue vertical changes and soft tissue horizontal changes.

• Proceedings of the Korea Crystallographic Association Conference
• /
• 1999.04a
• /
• pp.1-1
• /
• 1999

부유대용융법에 의하여 불순이온의 종류와 각 이온의 주입 농도를 달리하는 Rutile 단결정을 성장하였다. 성장된 결정으로부터 제조한 박편시료를 이용하여 결정결함과 광투과도에 미치는 각 불순이온의 영향을 조사하였다. 결정성장용 주원료로 99.99%의 TiO2를 사용하고, 불순이온 주입을 위한 원료로서 99.99%의 Al2O3, H3BO3, Ga2O3, Sc2O3, V2O5, Fe2O3, ZrO2, Er2O3, Cr2O3를 각각 사용하였다. 불순이온의 종류에 따르는 영향을 조사하기 위하여 TiO2 99.8 atomic%-불순이온 0.2atomic%의 조성이 되도록 각 이온별로 원료를 정밀하게 평량하고 균일 혼합하였다. 불순 이온의 첨가량에 따르는 영향을 조사하기 위하여 Al2O3는 각각 pure, 0.2, 0.4, 0.6 atomic%를, Cr2O3는 pure, 0.003, 0.05, 0.2 atomic%를 각각 치환하여 원료를 조합하였다. 균일 혼합된 원료를 직경 8mm의 고무 튜브에 넣고 CIP(Cold Isostatic Press0에서 2000kg/$\textrm{cm}^2$의 압력으로 성형한 후 150$0^{\circ}C$에서 1시간 소결함으로서 결정성장용 다결정 원료를 합성하였다. 합성된 다결정을 double ellipsoidal mirror 내에 설치하고,halogen lamp로 가열하여 원료의 한쪽 끝을 용융한 다음, 20rpm의 회전속도, 3-5mm/hr의 성장속도로 하는 유속 1$\ell$/min의 O2 분위기속에서 부유대용융법에 의하여 결정을 성장하였다. 성장된 결정을 성장축에 수직한 방향으로 각각 절단, 연삭, 연마한 박편을 이용하여 편광하에서 low-angle grain boundaries 및 기타의 결정결함을 관찰하였으며, 0.3$\mu\textrm{m}$~0.8$\mu\textrm{m}$ 범위 및 0.6$\mu\textrm{m}$~3.4$\mu\textrm{m}$ 범위에서의 투과 및 흡수 스펙트럼을 측정하였다. 결정 성장 결과 B3+, Er3+, Cr3+ 이온은 Ti4+ 이온과 이온의 크기 차이가 심하여 결정의 정상적인 성장을 방해하는 물성을 나타냈고, V5+, Cr3+ 이온은 흑색의 결정, Fe3+ 이온은 적갈색의 결정으로 성장되었다. Al3+, Zr4+, Al3+의 순서로 투과도가 높아지는 것이 관찰되었다. 불순이온의 농도에 따른 영향으로서 Al3+ 이온의 경우 주입농도가 높아질수록 low angle boundary와 oxygen deficiency가 감소하였고, 투과율은 조금 감소하거나 큰 차이가 없는 것으로 나타났다. 반면에 Cr3+ 이온을 주입한 경우 0.003 atomic%에서 최적의 물성을 보였으며, 주입농도가 높아질수록 결정성장이 어려워지고 광의 투과도가 급격히 저하되었다.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.46 no.11
• /
• pp.1327-1335
• /
• 2017

This study was carried out to determine the effect of cacao bean addition on the physicochemical properties of extruded rice flour. Rice-based cacao beans (0, 20, 40, 60%) were extruded at a die temperature of $130^{\circ}C$, screw speed of 200 rpm, and moisture content of 25%. As the content of cacao beans increased from 20% to 60%, expansion index decreased, while piece density and specific length increased. The water soluble index and water absorption index of the extrudate increased through extrusion cooking. Lightness decreased as cacao bean content increased while redness increased. As the content of cacao beans increased, paste viscosity decreased. Cold peak viscosity was observed in all extrudates of raw roasted cacao beans. ${\alpha},{\alpha}$-Diphenyl-${\beta}$-picrylhydrazyl (DPPH) radical-scavenging activity increased upon extrusion and cacao bean addition. As content of cacao beans increased, non-roasted cacao beans had higher total phenolic contents than roasted cacao beans. This study showed that addition of cacao beans to extruded rice snack improved antioxidant activity.

• Korean Journal of Applied Biomechanics
• /
• v.18 no.3
• /
• pp.61-69
• /
• 2008

The purpose of this study is to examine the success or failure on the balance beam in element group requirements posture which is bending salto side-ward tucked through kinetic analysis. The national team players were participated. The goal was to present training methods to coaches and athletes so as to provide scientifically useful information. The results from this study were summarized as below. When the performance was successful, the features of the body's center of gravity during the side somersault motion showed to spread from the center of the balance beam and the center of the gravity moved to the direction of the body's rotation. In the spring sections - event2 and 3, when the performance was successful, up/down fluctuation became more wider and increased air time. It supported the result that the projecting variable was higher than in failure trial. In addition, the right side hip joint angles and speed, and angular velocity as jumping up for a leap were larger than in failure trial. Those variables showed the optimal conditions for a leap. By increasing the speed of the upper limb from the shoulder and the speed of the shoulder joint angular velocity, the momentum was increased. Especially the right side shoulder joint angular velocity increased dramatically because the right leg was held. As to the side somersault motion, the angular momentum of successful trial with respect to x-axis was bigger than failed trial. It indicated that the increasing angular momentum with respect to x-axis was an important factor in flying motion. Besides, as to side somersault, the appropriate proportion of angular momentum with respect to y-axis and z-axis was a key to successful trails.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.15 no.2
• /
• pp.85-94
• /
• 2016

Lane Designation is defined as reasonable road management to ensure the road safety and enhance road efficiency. While the lane designation system was abolished in 1999, it was redefined because of the increasing number of large vehicles in the passing lane, violent on driving and traffic accidents in 2000. The needs of improvement on operating the lane designation has been increasing more in recent due to the low ratio of compliance with the system and difficulties to keep the right lane due to need of turning and demand of widening of designates lane for two-wheeled vehicles and truck. In this study, we presented the improvement plan through the question survey, simulation analysis, safety evaluation. It found a problem that the low-speed vehicle is to use the upper level roadway, difficulties of supervision, the imbalance in the lane use, imbalance traffic and does not match the international standards. This study suggested five different alternatives through the survey. micro simulation has used in order to examine each alternative by management effectiveness and feasibility. It analyzed the traffic speed, efficiency, traffic balance of alternatives. Also, safety evaluation conducted in terms of the range of field-of-view to ensure the easiness of field of view by various configurational difference between the vehicles. By the analysis results of such indicators, This study presents proposals for improvement in operating designated lane that low-speed-big-sized vehicles keep to the right lane, and high-speed-small sized vehicles keep to the left lane.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.74-74
• /
• 2015

최근 홍수의 특성과 피해 양상은 과거와는 다르게 변화하고 있으며, 급격한 도시화로 인하여 기존 하천유역의 저류 능력이 감소하였으며 이러한 한계를 극복하기 위하여 이미 외국에서는 대심도 터널을 활용한 홍수재해 관리방안이 오래전부터 활용되어 왔다. 본 연구에서는 대심도 터널의 유입구, 수직갱, 감세지, 배수터널과 같은 시설물 중 대심도 터널 설계 시 수직 유입구를 통해 유입되는 유량의 에너지를 완화하고 효과적으로 배수 할 수 있도록 중요한 역할을 하는 감세지의 효율적인 깊이 산정을 위하여 수리모형실험을 실시하였으며, 모형은 Froude 상사법칙을 사용하여 원형의 1/18크기로 제작하였다. 본 연구에서 실시한 감세지 모형의 깊이는 0.278 m(원형 5.0 m), 0.417 m(원형 7.5 m)이며, 각 감세지 깊이별 수직 유입구 3개소(저지수직구1, 저지수직구2, 고지수직구) 및 5가지의 유량 CASE에 대하여 감세지 바닥면 압력을 비교?분석 하였다. 수직 유입구 3개소의 설계조건에 따른 감세지 깊이별 바닥면 압력 분포 평가를 실시한 결과 저지수직구1의 감세지 깊이 0.278 m(원형 5.0m)에서는 최대 압력이 4번 지점에서 $0.075kg/cm^2$(원형 1.30 MPa)이 측정 되었으며, 0.417 m(원형 7.5m)에서는 최대 압력이 1번지점에서 $0.089kg/cm^2$(원형 1.54MPa)이 측정되었다. 또한 저지수직구2의 감세지 깊이 0.278 m(원형 5.0 m)에서는 최대 압력이 1번 지점에서 $0.074kg/cm^2$(원형 1.28 MPa)이 측정 되었으며, 0.417 m(원형 7.5 m)에서는 최대 압력이 2번지점에서 $0.088kg/cm^2$(원형 1.52 MPa)이 측정되었다. 고지수직구의 감세지 깊이 0.278 m(원형 5.0 m)에서는 최대 압력이 3번 지점에서 $0.082kg/cm^2$(원형 1.42 MPa)이 측정 되었으며, 0.417 m(원형 7.5 m)에서는 최대 압력이 1번지점에서 $0.092kg/cm^2$(원형 1.59 MPa)이 측정되었다. 본 연구에서 실시한 수리모형실험의 결과 저유량에서 고유량으로 갈수록 최대압력지점은 반시계방향으로 움직이는 것을 알 수 있으며, 이는 수직 유입구의 설계조건에 따른 수직갱에서의 회전수차에 의하여 발생하는 것으로 분석하였다. 따라서 적절한 감세지 깊이 산정을 위해서 대심도터널의 수직 유입구(유입구형태, 수직갱)의 평가가 함께 유기적으로 이루어져야 할 것으로 판단된다.

• Elastomers and Composites
• /
• v.38 no.3
• /
• pp.213-226
• /
• 2003

The cure and rheological behavior of diglycidyl ether of bisphenol F/nadic methyl anhydride resin system with the kinds of imidazole were studied using a differential scanning calorimeter (DSC) and a rotational rheometer. The isothermal traces were employed to analyze cure reaction. The DGEBF/ anhydride conversion profiles showed autocatalyzed reaction characterized by maximum conversion rate at $20{\sim}40 %$ of the reaction. The rate constants ($k_1,\;k_2$) showed temperature dependance, but reaction order did not. The reaction order (m+n) was calculated to be close to 3. There are two reaction mechanisms with the kinds oi catalyst. The gel time was determined by using G'-G" crossover method, and the activation energy was obtained from this results. From measurement of rheological properties it was found that the logarithmic 1:elation time of fused silica filled DBEBF epoxy compounds linearly increased with the content of filler and decreased with temperature. The highly filled epoxy compounds showed typical pseudoplastic behavior, and the viscosity of those decreased with increasing maximum packing ratio.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.3
• /
• pp.276-286
• /
• 2021

General high fluidity concrete is the area of high strength concrete with a high amount of cement to secure the required fluidity and workability. Since most of the concrete structures currently used have normal strength, there is a limit to the practical expansion and practicality of use. Thus it is necessary to develop normal strength-high fluidity concrete with low binders that can be used not only in general buildings but also in special buildings, and can greatly reduce construction time and save labor costs. This requires to develop and apply the polycarboxylate-based superplasticizer. In this study, PCE was prepared for each combination of starting materials(WR, HB, RT) and the rheological properties of cement paste were analyzed using ringflow cone and a rotary viscometer. As a result, when PCE with a combination of WR 80%, HB 6.5%, and RT 13.5% was applied, the yield stress can be minimized while securing the plastic viscosity at level of the normal strength. In addition, high fluidity due to the high dispersion effect was confirmed.

• Korean Chemical Engineering Research
• /
• v.56 no.6
• /
• pp.901-908
• /
• 2018

Graphite is used as a sample anode active material. However, since the maximum theoretical capacity is limited to $372mA\;h\;g^{-1}$, a new anode active material is required for the development of a high capacity lithium ion battery. The maximum theoretical capacity of Si is $4200mA\;h\;g^{-1}$, which is higher than that of graphite. However, it is not suitable for direct application to the anode active material because it has a volume expansion of 400%. In order to minimize the decrease of the discharge capacity due to the volume expansion, the Si was pulverized by the dry method to reduce the mechanical stress and the volume change of the reaction phase, and the change of the volume was suppressed by coating the carbon layers to the particle size controlled Si particles. And carbon fiber is grown like a thread on the particle surface to control secondary volume expansion and improve electrical conductivity. The physical and chemical properties of the materials were measured by XRD, SEM and TEM, and their electrochemical properties were evaluated. In this study, we have investigated the synthesis method that can be used as anode active material by improving cycle characteristics of Si.