• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.7
• /
• pp.9-15
• /
• 2019

The purpose of present study is to assess the maximum width of the surface cracks using the histogram analysis of image processing techniques in concrete structures. For this purpose, the concrete crack image is acquired by the camera. The image is Grayscale coded and Binary coded. After Binary coded image is Dilate and Erode coded, the image is then recognized as separated objects by applying Labeling techniques. Over time, dust and stains may occur naturally on the surface of concrete. The crack image of concrete may include shadows and reflections by lighting depending on a surrounding conditions. In general, concrete cracks occur in a continuous pattern and noise of image appears in the form of shot noises. Bilateral Blurring and Adaptive Threshold apply to the Grayscale image to eliminate these effects. The remaining noises are removed by the object area ratio to the Labeled area. The maximum numbers of pixels and its positions in the crack objects without noises are calculated in x-direction and y-direction by Histogram analysis. The widths of the crack are estimated by trigonometric ratio at the positions of the pixels maximum numbers for the Labeled objects. Finally, the maximum crack width estimated by the proposed method is compared to the crack width measured with the crack gauge. The proposed method by the present study may increase the reliability for the estimation of maximum crack width using image processing techniques in concrete surface images.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.12
• /
• pp.723-729
• /
• 2016

This study compared fin-tube and parallel-flow heat pipes for their sensible heat exchange rate, heat recovery amount, and air-side pressure drop. Tests were done with different refrigerant charging rates of 40-60% vol. and air flow rates of 300-1,400. The sensible heat exchange rate was highest for both types of heat pipes at a working fluid charge of 40% vol. and low flow rate. For the parallel-flow heat pipe, the 60% vol. charge is too high and results in a low sensible heat exchange rate. The reason is that the thicker liquid film of the tube wall deteriorates the heat transfer effect. Hence, the optimal charging rate is 40 to 50% vol. The evaporator heat pipe has a larger air-side pressure drop than the condenser section heat pipe. The reason is considered to be condensation water arising from the evaporator surface. Compared to the fin-tube heat pipe, the parallel-flow heat pipe showed better performance with a working fluid charging rate of 48%, volume of 41%, and an air-side pressure drop about 37%.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.2
• /
• pp.84-90
• /
• 2001

To investigate morphological characteristics of zephyr produced from two bamboo species, Phyllostachys nigra var. henonis and Gigantochloa apus, basic anatomic properties were examined by scanning electron microscopy and image analysis. According to SEM observation, zephyr from Phyllostachys nigra var. henonis was not of uniform in shape and showed macro crack between vascular bundle sheaths. This may be attributes to the sclerenchymatous fibers connected closely, thus resulting in difficult separation of intercellular layer. Zephyr from Gigantochloa apus was of uniform in shape, which may be caused by easy separation of intercellular layer of sclerenchymatous fibers having thin cell wall and large cell lumen. By image analysis in cross section of two species, the ratio of vascular bundle sheaths and cell wall ratio of sclerenchymatous fibers were examined. The ratio of vascular bundle sheaths in Phyllostachys nigra var. henonis was lower than that in Gigantochloa apus. However, cell wall ratio of sclerenchymatous fibers in Phyllostachys nigra var. henonis was higher than that in Gigantochloa apus.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.22 no.1
• /
• pp.19-24
• /
• 2012

Barium zirconate exhibits good thermo-chemical stability and proton conduction at high temperatures, but shows poor electron conductivity. Therefore, for high efficiency of hydrogen separation, a very thin and dense Pd-Barium zirconate membrane has to be coated on a porous substrate. A thin and dense Pd-Barium zirconate membrane was successfully synthesized on a porous substrate by means of dual sputtering method. The structural and chemical features of the $BaZr_{0.85}Y_{0.15}O_{3-{\delta}}$ membranes sputtered at $300^{\circ}C$ and $400^{\circ}C$ were investigated by X-ray diffractometry, and it was found that a well-crystallized membrane, Pm-3m space group of $BaZrO_3$, was synthesized. The surface and cross-sectional morphologies of membrane were assessed by SEM (scanning electron microscopy) and TEM(transmission electron microscopy) of the surface and of cross sections. The cross sectional observation of Pd-$BaZr_{0.85}Y_{0.15}O_{3-{\delta}}$ membrane by dual sputtering shows that the coating is quite dense with columnar structure.

• Membrane Journal
• /
• v.27 no.5
• /
• pp.389-398
• /
• 2017

The most important characteristic of the polymer electrolyte membranes (PEMs) for fuel cells, the proton conducting ability is mainly influenced by the distribution and morphology of the water channels inside the PEMs. Non-perfluorinated hydrocarbon PEMs are known to have weaker water channels than perfluorinated PEM, Nafion, and thus relatively low proton conducting ability. In this study, we used a mesoscale simulation technique to observe the water channel formation and phase separation behavior of hydrocarbon PEM, sulfonated polyimides, under the humidification condition. It was observed that the water molecules were distributed evenly through the entire hydrophilic region, and clear water clusters were formed only in the sulfonated polyimide having high sulfonation degree. In addition, it was observed that sulfonated polyimides have a difficulty in forming water channel under the low hydrated condition. These results clearly support the theories of the formation of water channels in non-perfluorinated hydrocarbon PEMs, and also well explain the tendency of proton conducting abilities of sulfonated polyimides. Thus, it is confirmed that mesoscale simulation techniques can be very effective in analyzing phase separation behavior and water channel formation in PEMs for fuel cells and elucidating the ion conducting abilities.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.3-3
• /
• 2009

선박의 건조과정에서 필수적으로 선체 외판에는 선박의 안전과 운항 및 정비 등에 필요한 정보를 나타내기 위해 다양한 종류의 마크 및 문자가 마킹되어진다. 하지만, 단순한 도장 작업만으로는 해상과 같은 부식 환경에서 마크 및 문자가 쉽게 지워지거나 손상되기 때문에 마크 및 문자를 용접 비드(welding bead)로 표시하거나 미리 절단된 강판(steel plate)을 수동으로 용접한 뒤 도장을 함으로써 마크 및 문자의 손상을 방지하고 있다. 이러한 문자마킹작업을 하기 위해서는 작업자가 수작업으로 기준선과 마크 및 문자의 위치를 먹줄 등을 이용하여 마킹을 하고, 해당 마크 및 문자의 템플렛(template)을 이용하여 펀칭을 실시한 후 수동으로 용접을 실시한다. 하지만, 수작업을 통한 선체외판 문자마킹 작업은 작업자의 기량에 따라 품질이 상이하여 품질 저하의 원인이 된다. 또한 대조립 및 탑재 단계에서 문자 마킹 작업시 수직자세의 용접을 요구함으로써 작업자가 안전사고에 노출되어 있으며, 선박의 각 단계별 주요 공정보다 작업시간이 길어져 전체 선박 건조공정을 지연시키는 문제점 등을 야기시킬 수 있다. 이러한 문제점들을 해결하기 위해 조선업계에서는 선체 외판의 마크 및 문자를 자동으로 용접할 수 있는 장치를 개발하기 위해 노력해왔으며, 몇몇 개발 사례가 보고되고 있다. 하지만, 그 실효성 부분에서는 아직까지 해결하지 못한 문제점들로 인해 현장 적용에는 어려움을 보이고 있다. 본 연구에서는 선박외판 문자 자동용접장치의 기능성뿐만 아니라 현업 적용성을 가장 우선적으로 고려하여 문자마킹장치(Marking Robot for Shipbuilding) 개발을 진행하였다. 우선, 적절한 용접 재료를 선정하기 위해서 솔리드 와이어(Solid Wire)와 플럭스 코어드 와이어(Flux Cored Wire)에 대한 비드온 용접(Bead-On Welding)을 아래보기자세와 수직자세에 대해서 실시하여 적절한 용접 조건을 설정하였다. 본 연구에서 개발된 문자마킹 자동용접장치는 3축으로 구성되어 있으며 각 축들을 분리할 수 있도록 개발하여 이동성을 향상시켰으며, 작업면과 용접토치간의 거리를 일정하게 유지시킬 수 있도록 용접전류 센서(Welding Current Sensor)를 이용하여 토치 높이(Wire Extension)를 제어함으로써 균일한 품질의 용접비드를 얻을 수 있었다. 또한 문자마킹 자동용접장치는 본체 구동부와 제어부(Touch Screen)가 쉽게 분리되고 장착이 가능한 구조로 개발되었으며, 용접시 각 용접자세별로 용접전압, 전류 그리고 용접속도 설정이 가능하여 아래보기 자세뿐만 아니라 어떠한 자세에서도 같은 모양의 비드형상을 가지는 문자마킹용접이 가능하도록 개발하였으며, 이는 실험과 현장적용을 통해 검증하였다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.17 no.4
• /
• pp.375-387
• /
• 2004

A new finite element model will be presented to analyze the nonlinear behavior of RC beams and slabs strengthened by a patch repair. The numerical approach is based on the p-version degenerate shell element including theory of anisotropic laminated composites, theory of materially and geometrically nonlinear plates. In the nonlinear formulation of this model, the total Lagrangian formulation is adopted with large deflections and moderate rotations being accounted for in the sense of von Karman hypothesis. The material model is based on hardening rule, crushing condition, plate-end debonding strength model and so on. The Gauss-Lobatto numerical quadrature is applied to calculate the stresses at the nodal points instead of Gauss points. The validity of the proposed p-version nonlinear finite element model is demonstrated through the load-deflection curves, the ultimate loads, and the failure modes of RC beams or slabs bonded with steel plates or FRP plates compared with available result of experiment and other numerical methods.

• Membrane Journal
• /
• v.26 no.2
• /
• pp.116-125
• /
• 2016

This study described a synthesis of MF having a arsenic removal characteristics and the fundamental research was performed about the simultaneous removal system of both As(III) and As(V) ions with the composite nanofiber membrane (PMF) based on PVdF and MF materials for the water-treatment application. From the TEM analysis, the shape and structure of MF materials was investigated. The mechanical strength, pore-size, contact angle and water-flux analysis for the PMF was performed to investigate the possibility of utilizing as a water treatment membrane. From these results, the PMF11 showed the highest value of mechanical strength ($232.7kgf/cm^2$) and the pore-diameter of composite membrane was reduced by introducing the MF materials. In particular, their pore diameter decreased with an increase of iron oxide composition ratio. The water flux value of PMF was improved about 10 to 60% compared with that of neat PVdF nanofiber membranes. From the arsenic removal characterization of prepared MF materials and PMF, it was shown the simultaneous removal characteristics of both As(III) and (V) ions, and the MF01, in particular, showed the highest adsorption-removal rate of 93% As(III) and 68% As(V), respectively. From these results, prepared MF materials and PMF have shown a great potential to be utilized for the fundamental study to improve the functionality of water treatment membrane.

• Cartoon and Animation Studies
• /
• s.41
• /
• pp.407-427
• /
• 2015

This thesis is research about the development and application of the panorama image in contemporary artwork, focusing on sculpture and installation. The samples of artworks are a selection of representatives from numerous examples of works that cannot be introduced without exceeding a reasonable scope of the thesis. A brief outline of the historical concepts of the perspective will describe the development of the panorama in itself. Some technical explanations and the practical use of the panorama with its link to 3-dimensional applications should bridge the explanation gap between the 2nd and 3rd dimensional usage of the panorama in contemporary artwork. Furthermore, some philosophical statements are proposed in the discussion. One of the main interests and initial motivation of this study was my personal believe that there is always a relationship between social philosophical values and the way a society sees or encounters visual structures. In other words the contemporary understanding of space and perspective is mirroring the actual zeitgeist and creates an exemplary visual aesthetics.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.2
• /
• pp.124-134
• /
• 2013

This study investigated the effect of surface water on concrete substrate on adhesive strength in tension of very high flowable SBR-modified cement mortar. The specimens were prepared with proportionally mixing SBR latex, ordinary portland cement, silica sand, superplasticizer and viscosity enhancing agent. Polymer cement ratio (P/C) were 10, 20, 30, 50 and 75% and the weight ratio of fine aggregate to cement were 1:1 and 1:3. The specimens obtained with different P/C and C:F were characterized by unit weight, flow test, crack resistance and adhesion test. After basic tests, two mixtures of P/C=20% and 30% in case of C:F=1:1, and one mixture of P/C=50% in case of C:F=1:3 were selected, respectively. These three selected specimens were studied about the effect of surface water evenly sprayed on concrete substrate by a amount of 0, 0.006, 0.012, 0.017, 0.024g per unit area ($cm^2$) of concrete substrate surface The results show that surface water on concrete substrate increases the adhesive strength in tension of high flowable SBR-modified cement mortar and improve the flowability compared to the non-sprayed case.