• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.10
• /
• pp.979-987
• /
• 2008

In aerospace structural design, the position of lightening hole is often required to be optimized from the initial design in order to avoid an excessive stress concentration. To remodel the updated configuration in optimization procedure, re-meshing procedure is conventionally adopted. However, this approach is time-consuming, and has limitations especially in handling hexahedral or quadrilateral meshes, which are preferred because of their good numerical performances. To attenuate these disadvantages, new optimization scheme is proposed by combining the MLS(Moving Least Squares) based overset method and the genetic algorithm in this work. To test the validity of the proposed optimization scheme, optimizations of positions of lightening holes in 2D structures have been carried out.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.10
• /
• pp.940-947
• /
• 2007

For the performance upgrade of a supersonic jet fighter, the processor and FLCC(Flight Control Computer) Architecture were upgraded from a baseline FLCC. Prior to the hardware implementation phase, the exact CPU throughput estimation is necessary. For this purpose, an experimental method for new FLCC throughput estimation was introduced in this study.　While baseline FLCC operating, the CPU address bus was collected with logic analyzer, and then decoded to get the exact access times to each memory-memory and the number of program Instruction branches. Based on these data, a throughput test in CPU demo-board of the new FLCC configuration was performed. From test results, the CPU-Memory architecture was design-changed before FLCC hardware implementation phase. To check the flight stability degradation due to power-interrupt problem due to CPU-Memory architecture change, the piloted HILS (Hardware-In-the Loop Simulator) test was conducted.

• Journal of the Korean Electrochemical Society
• /
• v.11 no.1
• /
• pp.51-58
• /
• 2008

Many researches for effects of different flow configurations on performance of Proton Exchange Membrane Fuel Cell have extensively been done but the effects of flow direction at the same flow channel shape should be considered for optimal operation of fuel cell as well. In this paper a numerical computational methode for simulating entire reactive flow fields including anode and cathode flow has been developed and the effects of different flow direction at parallel flow was studied. Pressure drop along the flow channel and density distribution of reactant and products and water transport, ion conductivity across the membrane and I-V performance are compared in terms of flow directions(co-flow or counter-flow) using above numerical simulation method. The results show that the performance under counter-flow condition is superior to that under co-flow condition due to higher reactant and water transport resulting to higher ion conductivity of membrane.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.6
• /
• pp.78-84
• /
• 2017

Consistent efforts have been made to reduce the weight of automotive parts by using lightweight materials. This has resulted in the replacement of conventional steels in car body structures with high-strength steels, and the current usage rate has reached 50%. This study examines the structural stiffness and energy absorption capability of bumper beams made of high-strength steels. New types of bumper beam cross sections are proposed.The structural stiffness and maximum bending force were computed via finite element analysis as about 25tons and 7.5tons/mm, and there were no significant differences among the proposedcross sections. Dynamic analysis was also carried out to investigate the energy absorption capabilities of the bumper beams, and the effects of materials and thickness reduction were analyzed. High-strength steel can be used to achieve weight reduction with comparable structural performance to conventional bumper beams.

• Journal of the Korean Society for Railway
• /
• v.13 no.4
• /
• pp.404-411
• /
• 2010

Authors conducted a deduction and characteristic calculation of the some parameters using a magnetic equivalent circuit method to verify a basic design result of a rotary-typed small-scaled linear induction motor for a railway transit. In a LIM, it is possible to express the parameters of the magnetic equivalent circuit into a function of the shape of the secondary aluminium plate and the airgap between the LIM primary core and the secondary aluminium plate. It means that the LIM properties can be changed considerably by the shape of the secondary aluminium plate and the airgap between the LIM primary core and the secondary aluminium plate. So, authors analyzed a tendency of changes of the magnetic equivalent circuit parameters and the LIM characteristics by changing of the airgap, the thickness of the secondary aluminium plate and the overhang length and shape of a rotary-typed small-scaled LIM, and accomplished a basic research to develop a real-scaled LIM for a railway transit.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.7
• /
• pp.709-716
• /
• 2013

A fan filter unit (FFU) is a device which supplies clean air from the ceiling in a clean room. With an increase in its size, velocity variation occurs within the exhaust plane and this damage the product quality or productivity. Hence, a guide vane is installed inside the device to enhance the velocity uniformity. Because the vane reduces the flow rate for a given pumping power, an optimum design is required to achieve velocity uniformity while minimizing the flow rate reduction at the same time. To find a geometry that satisfies these requirements, a series of numerical simulations has been conducted while changing the angle and length of the guide vanes. By changing the geometry of the side guide vane, the velocity uniformity increased by 3.7% and the flow rate decreased by 1.5%. For the center guide vane, the velocity uniformity increased by 2.9% and the flow rate decreased by 0.7%.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.3
• /
• pp.70-77
• /
• 2014

In this paper, the development of unique model of the 2.75 inch rocket propulsion system is described. Recently developed korean 2.75 inch rocket propulsion system shows the improvement of a flame stability resulted from a change in the configuration of propellant grain, and of an incidental ignition protection function using the EMI(electromagnetic interference) filter on ignition system. Moreover it is shown that a directional flight stability is improved by increasing the number of fins and changing the nozzle configuration. Static firing test and thermal shock test were conducted for the validation before flight, and flight test of 210 rounds of rockets was conducted to verify the trajectory uniformity. In addition, intellectual property issues can be overcome with the unique korean 2.75 inch rocket motor as well as the performance improvement.

• Journal of the korean Society of Automotive Engineers
• /
• v.18 no.6
• /
• pp.23-32
• /
• 1996

차량에서 엔진은 가장 큰 질량 집중체(concentrated mass)이다. 만약 엔진이 적절하게 구속되지 않거나 절연되어 있지 않으면, 차체에 진동을 일으키는 원인이 된다. 엔진은 다양한 진동 교란을 받는데 엔진 마운트는 이러한 모든 것들을 고립시키는 역할을 해야 하며, 엔진은 정적인 장착 하중에 대한 지지와 전후, 좌우 및 수직 방향의 운동에 대해 적절한 강성을 가져야 한다. 또한 정숙성을 향상시키기 위해서는 엔진 마운트의 재료인 고무의 강성계수를 낮추는 것이 필요한데 이는 일반적으로 내구성의 저하를 가져온다. 따라서 개발과정에서 강성계수를 낮추는 변경을 하면 부품의 내구성을 보정함에 따르는 재평가 또한 필요하게 된다. 엔진 마운트에 쓰이는 고무부품의 해석은 엔진 마운트 시스템에 대한 진동 해석 및 내구수명의 예측과 병행해야 하며, 진동해석으로부터 얻은 하중 지지 능력 등의 모든 요구 특성을 만족하기 위해서는 고무 재료의 특성에 대한 지식, 엔진 마운트의 장착 위치에 대한 결정 능력과 함께 주어진 조건에 대한 형상의 최적 설계 능력 등이 요구된다. 본 연구에서는 기본적인 형상을 파라미터화하여 엔진 마운트의 형상을 최적화 하는 절차를 제안하였다. 현재 승용차에 널리 사용되고 있는 부시형(bush type) 엔진마운트를 적용 모델로 선택하였으며, 엔진 마운트의 기본적인 형상을 몇개의 파라미터를 사용하여 정의하고 설계 사양으로 주어지는 강성값과 각 파라미터들의 조합으로 구성되는 형상이 갖는 강성값의 차이가 최소가 되도록 파라미터 값들을 최적화하였다. 최적화된 파라미터 값들로 구성되는 형상을 내구 성능, 성형성등을 고려하여 최종 형상으로 결정한다. 내구성능의 예측은 금속부품의 내구수명 예측에 널리 이용되고 있는 방법이 방진 고무부품의 경우에도 적용 가능한지를 검토하고, 방진 고무부품에도 일반적으로 적용될수 있는 내구수명 예측방안의 개발 가능성을 타진해 보았다. 본 연구의 목표는 시제품을 제작하기 이전에 설계된 부품에 대한 스프링 상수 및 내구특성을 체계적으로 규명하여 제품 시험의 횟수를 줄이고, 보다 정밀한 제품을 제작할 수 있도록 하기 위한 것이다.

• Journal of the Society of Naval Architects of Korea
• /
• v.32 no.3
• /
• pp.19-28
• /
• 1995

This paper presents hull form design details and performance characteristics of the SWATH ship 'SEON JIN' built as an underwater test support ship. The hull form is developed systematically varing sets of 11 form parameters which define a unique hull under waterline. Using this geometry variation scheme we have generated a number of alternatives and selected the final hull which fulfills the design objectives and matches the design constraints. After selecting the final hull form we have investigated performances thoroughly through model tests, and confirmed through sea trials that the performance goals be achieved.

• Aerospace Engineering and Technology
• /
• v.7 no.2
• /
• pp.88-94
• /
• 2008

In this study, triaxial velocity is analyzed for COMS(Communication, Ocean and Meteorological Satellite) configuration, which is generated when thrusters are used to dump wheel momentum. Since COMS is designed to periodically change the thruster set in order to uniformly decrease the performance of thrusters, triaxial velocity would be different during the change of thruster set. So, the triaxial velocity generated due to the change of thruster set is optimized.